Hama EWS-860 Bedienungsanleitung

123125

EWS-860

Weather Station

Wetterstation

RUS

Operating Instructions

Bedienungsanleitung

Mode d‘emploi

Instrucciones de uso

Руководство по эксплуатации

Istruzioni per l‘uso

Instrukcja obsługi

20 23

14 13

GOperating instruction

Controls and Displays

ABase station

1. Atmospheric pressuretrend

2. Weather forecast symbol

3. Measuring station wireless symbol

4. Channel display

5. Outdoor temperaturetrend

6. Outdoor temperature

7. Room temperaturetrend

8. Room temperature

9. Time/date

10. Alarm symbol

11. Weekday /seconds

12. Wireless symbol

13. Time zone

14. Room humidity

15. Room humidity trend

16. Outdoor humidity

17. Outdoor humidity trend

18. button =increasing the current setting /activating/ deactivating manual radio signal

reception /Switches between TIME and temperaturemode

19. button =reducingthe current setting /manually searching for the signal from the

measuring station /Switches between TIME and temperaturemode

20. mode button =settings /conrming the setting /toggling between seconds, weekday

and time zone display /Switches between °C and °F

21. alarm button =display /setting alarm modes

22. channel button =channel selection

23. mem.button =accessing/ resetting the stored maximum/minimum values

24. Battery compartment

BMeasuring station

25. Battery compartment

26. Mounting plate

27. Cut-out for vertical mounting

28. Cut-out for horizontal mounting

29. Clips

Thank you for choosing aHama product.

Take your time and read the following instructions and information completely.Please keep

these instructions in asafe place for futurereference. If you sell the device, please pass these

operating instructions on to the new owner.

1. Explanation of Warning Symbols and Notes

Warning

This symbol is used to indicate safety instructions or to draw your attention to specic

hazards and risks.

Note

This symbol is used to indicate additional information or important notes.

2. Package Contents

•Weather station EWS-860

(base station for indoor/outdoor measuring station)

•Base

•4xAAA batteries

•These operating instructions

3. Safety Instructions

•The product is intended for private, non-commercial use only.

•Do not operate the product outside the power limits given in the specications.

•Do not use the product in moist environments and avoid splashes.

•Do not use the product in the immediate vicinity of heaters or other heat sources or in

direct sunlight.

•Do not use the product in areas wherethe use of electronic devices is not permitted.

•Do not place the product near interference elds, metal frames, computers, TVs, etc.

Electronic devices and window frames can negatively affect the product’sfunctionality.

•Do not drop the product and do not expose it to any major shocks.

•Do not open the device or continue to operate it if it becomes damaged.

•Do not attempt to service or repair the product yourself.Leave any and allservice work to

qualied experts.

•Keep the packaging material out of the reach of children due to the risk of suffocation.

•Dispose of packaging material immediately according to locally applicable regulations.

•Do not modify the product in any way.Doing so voids the warranty.

Warning –Batteries

•Immediately remove and dispose of dead batteries from the product.

•Only use batteries (or rechargeable batteries) that match the specied type.

•Do not mix old and new batteries or batteries of adifferent type or make.

•When inserting batteries, note the correct polarity (+ and -markings) and insert

the batteries accordingly.Failure to do so could result in the batteries leaking or

exploding.

•Do not charge batteries.

•Keep batteries out of the reach of children.

•Do not short circuit the batteries/rechargeable batteries and keep them away from

uncoated metal objects.

4. Getting Started

4.1. Measuring station

•Open the battery compartment (25) and insert two AAA batteries with the correct polarity.

Close the battery compartment.

Note

Beforeuse, ensureyou insert the batteries in the measuring station rst and then in the

base station.

4.2. Base station

•Open the battery compartment (24) and insert two AAA batteries with the correct polarity.

Close the battery compartment.

5. Installation

Note –Installation

•We recommend initially placing the base and measuring stations in the intended

locations without installing them and making all the settings described in

6. Operation –todo.

•Only install the stations once the appropriate settings have been made and astable

wireless connection is established.

Note

•The wireless transmission range between the measuring and base stations is up to 30

minopen spaces.

•Beforeinstallation, ensurethat wireless transmission will not be disrupted by

interference or obstacles like buildings, trees, vehicles, high-voltage lines, etc.

•Beforethe nal installation, ensurethat thereissucient reception between the

intended installation locations.

•When installing the measuring station, ensurethat it is protected from direct sunlight

and rain.

•The international standardheight for measuring air temperatureis1.25 m(4ft) above

ground.

Warning

•Buy special or suitable installation material from aspecialised dealer for wall-mounting.

•Ensurethat no faulty or damaged parts areinstalled.

•Never apply force during installation. This could damage the product.

•Beforeinstallation, ensurethat the chosen wall is suitable for the weight to be

mounted, and make surethat thereare no electrical wires, water,gas or other lines at

the installation site on the wall.

5.1. Base station

•Use the base to position the base station on alevel surface. (C)

5.2. Measuring station

•Youcan fasten the measuring station horizontally or vertically to an outer wall using a

mounting plate (26).

•If you want to mount the measuring station horizontally,use rawl plugs, screws, etc. to

fasten the mounting plate (26) using the central cut-out (28) to the wall intended for

installation.

•If you want to mount the measuring station vertically,use rawl plugs, screws, etc. in the

wall intended for installation and hang the mounting plate (26) using cut-out (27).

•Gently push the measuring station until you hear alatching sound (“click”) as it engages

with the clips (29).

6. Operation

Note –Input

Hold down the -button (18) or the -button (19) to select the values faster.

6.1. Connection to the measuring station

•After you insert the batteries, the base station automatically searches for aconnection to

the measuring station and performs initial setup.

Note

•Initial setup takes approx. 3minutes.

•During connection, the wireless symbol on the measuring station will ash (3).

•Do not press any buttons during setup. Otherwise, values may not be transmitted

correctly and thereisarisk of value errors and inaccuracies.

•The setup process is completed when the indoor (18, 14) and outdoor (6, 16)

measurement data is displayed.

•If the base station still does not receive asignal from the measuring station, press and hold

the -button (19) for approx. 3seconds to start the manual search for the signal.

Display Search for asignal from the measuring station

Display ashing Active

Displayed continuously Successful –signal is being received

Displayed continuously Inactive –nosignal reception for >1hour

6.2. Selecting the channel/other measuring stations

Note

•Youcan install two moremeasuring stations in addition to the included measuring

station. Ensurethat the base and measuring stations areset to the same channel.

Visit www.hama.com for suitable measuring stations.

•The transmission channel on the supplied measuring station cannot be changed/set

(CH1).

•Press the channel button (22) repeatedly to set the channel to that set on the respective

measuring station. CH1,CH2 or CH3 (4) is displayed.

•Select CH1 if you areonly using the measuring station supplied.

•The base station now shows the data measured (16, 6) on the selected measuring station

(4).

•Press and hold the channel button (22) to select the channel scan. The symbol and

measurement values of the individual measuring stations/channels (4) aredisplayed

consecutively for 5seconds each.

6.3. Basic and manual settings

Automatic setting using the DCF signal

After the rst time the base station is switched on and successful transmission is established

between the base station and the measuring station, the clock will automatically search for a

DCF signal. During the search, the wireless symbol (12) will ash.

Display Searching for the DCF signal

Display ashing

Active

Displayed continuously

Inactive –nosignal reception in the last 24

hours

Displayed continuously Successful –signal is being received

Displayedcontinuously

Successful –strong signal

•If the station still does not receive asignal, press and hold the –button (18) for approx.

3seconds to start the manual search for the DCF signal. The wireless symbol (12) will start

to ash.

Note –Time settings

•The search process takes about 3-10 minutes. If the search fails, it ends and is repeated

at the next clock hour.

•In the meantime you can, however,set the time and the date manually.

•The clock automatically continues to search for the DCF signal on adaily basis (00:00

a.m., 03:00 a.m., 06:00 a.m., 12:00 p.m.). If the signal is received successfully,the

manually-set time and date areoverwritten.

•Press and hold the –button (18) again for approx. 3seconds to stop the manual search.

Manually setting the date/time

Note –TIME mode

•Press the button (18) or the button (19) repeatedly until the symbol starts

ashing in the display.

Note –Time and time zone

•In TIME mode, press the mode button (20) repeatedly to toggle between the following

different displays:

•Time with seconds display,time with weekday display,time adjusted according to time

zone with weekday display,time adjusted according to time zone with seconds display,

date

•The time zone symbol (13) is displayed when the time has been adjusted according to

the time zone.

•Press and hold the -button (18) for approx. 3seconds to stop the search for the DCF

signal. The wireless symbol (12) goes out and you can set the time manually.

•In TIME mode, repeatedly press the mode button (20) until the time zone symbol (13) is

no longer displayed.

•Press and hold the mode button (20) for approx. 3seconds to make the following settings

one after the other:

•Weekday (11)

•Year (9)

•Month (9)

•Day (9)

•D/M –M/D (9) display

•12/24 hour format (9)

•Hours (9)

•Minutes (9)

•To select the individual values, press the -button (18) or the -button (19) and conrm

each selection by pressing the mode button (20).

•If you do not make an entry for 2minutes, you automatically exit the setup mode.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Hama Wetterstation Handbücher

Hama

Hama EWS-1000 Bedienungsanleitung

Hama

Hama 00075297 Bedienungsanleitung

Hama

Hama TH500 Bedienungsanleitung

Hama

Hama 186421 Bedienungsanleitung

Hama

Hama 00092659 EWS-165 Bedienungsanleitung

Hama

Hama EWS Intro Bedienungsanleitung

Hama

Hama EWS-890 Bedienungsanleitung

Hama

Hama EWS-700 Bedienungsanleitung

Hama

Hama EWS-900 Bedienungsanleitung

Hama

Hama 00136263 EWS-3300 Bedienungsanleitung

Hama

Hama EWS-830 Bedienungsanleitung

Hama

Hama Black Line Plus Bedienungsanleitung

Hama

Hama EWS-420 Bedienungsanleitung

Hama

Hama EWS-880 Bedienungsanleitung

Hama

Hama EWS-720 Bedienungsanleitung

Hama

Hama EWS-180 Bedienungsanleitung

Hama

Hama Color Edge 00136294 Bedienungsanleitung

Hama

Hama TH500 Bedienungsanleitung

Hama

Hama EWS-280 Bedienungsanleitung

Hama

Hama EWS-380 Bedienungsanleitung

Hama

Hama TH-200 Bedienungsanleitung

Hama

Hama EWS-100 Bedienungsanleitung

Hama

Hama EWS-751 Bedienungsanleitung

Hama

Hama EWS-400 Bedienungsanleitung

Beliebte Wetterstation Handbücher anderer Marken

Auriol

Auriol AHFL 433 A1 Bedienungsanleitung

Hyundai

Hyundai WS 2202 Bedienungsanleitung

NexSens

NexSens G2-HYDROMET Bedienungsanleitung

IROX

IROX HBVR761 UV-X Bedienungsanleitung

La Crosse Technology

La Crosse Technology C86371 Bedienungsanleitung

ADE

ADE WS 1711 Bedienungsanleitung

Auriol

Auriol z29592 Bedienungsanleitung

Auriol

Auriol 296289 Bedienungsanleitung

Hyundai

Hyundai WS 2266 Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-2210 Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-811561 Bedienungsanleitung

Ventus

Ventus W177 Bedienungsanleitung

National Geographic

National Geographic VA Colour RC Bedienungsanleitung

Levenhuk

Levenhuk Discovery Report WA40 Bedienungsanleitung

Instant Transmission

Instant Transmission MA 10410 Bedienungsanleitung

Lutron Electronics

Lutron Electronics PHB-318 Bedienungsanleitung

WAREMA

WAREMA EWFS Weather station eco Bedienungsanleitung

TFA

TFA 30.3013.IT Bedienungsanleitung