Hama EWS-830 Bedienungsanleitung

RUS

Operating Instructions

Bedienungsanleitung

Mode d‘emploi

Instrucciones de uso

Руководство по эксплуатации

Istruzioni per l‘uso

Οδηγίες χρήσης

Instrukcja obsługi

Návod na použitie

Manual de instruções

EWS-830Weather Station

Wetterstation

123129

SNOOZE/LIGHT

MODE HISTORY

+_CHANNEL

15 1617 18

36 37 38 39

25 26

1234

42 43

GOperating instruction

Controls and Displays

ABase station

1. Atmospheric pressuretrend

2. Weather forecast symbol

3. Risk of frost

4. Atmospheric pressure

5. Atmospheric pressurehistory

6. Room temperature

7. Comfort range

8. Room temperaturetrend

9. Battery symbol (base station)

10. Room humidity

11. Room humidity trend

12. Time

13. Day

14. Month

15. Sunrise

16. Moon phase

17. Town/City

18. Sunset

19. Calendar week

20. Weekday

21. Outdoor humidity trend

22. Outdoor humidity

23. Battery symbol (measuring station)

24. Channel overview

25. Outdoor temperaturetrend

26. Outdoor temperaturealarm

27. Alarm symbol

28. Outdoor temperature

29. Measuring station wireless symbol

30. Channel display

31. Summer time

32. Wireless symbol

33. 12 hour atmospheric pressurehistory

34. SNOOZE/LIGHT button =stops the alarm/activates the backlight (approx. 5seconds)

35. MODE button =settings/conrms the setting/switches the display mode

36. +button =increases the current set value/accessing the saved maximum/minimum values

37. –button =decreases the current set value/toggles between °C and °F/activates/deactivates outdoor

temperaturealarm

38. HISTORY button =for setting the height/ weather forecast/ atmospheric pressureunit/accessing saved air

pressurevalues

39. CHANNEL button =channel selection/manual search for asignal from the measuring station

40. Battery compartment

BMeasuring station

41. Transmission indicator lamp

42. Display

43. CH-/TX button =channel selection

44. Opening for wall mounting

45. °C/°F button =switches between °C and °F

46. Battery compartment

Thank you for choosing aHama product.

Take your time and read the following instructions and information completely.Please keep these instructions

in asafe place for futurereference. If you sell the device, please pass these operating instructions on to the

new owner.

1. Explanation of Warning Symbols and Notes

Warning

This symbol is used to indicate safety instructions or to draw your attention to specic hazards and risks.

Note

This symbol is used to indicate additional information or important notes.

2. Package Contents

•Weather station EWS-830 (base station for indoor/outdoor measuring station)

•2xAAA batteries

•2xAAbatteries

•These operating instructions

3. Safety Instructions

•The product is intended for private, non-commercial use only.

•Donot operate the product outside the power limits given in the specications.

•Donot use the product in moist environments and avoid splashes.

•Donot use the product in the immediate vicinity of heaters or other heat sources or in direct sunlight.

•Donot use the product in areas wherethe use of electronic devices is not permitted.

•Donot place the product near interference elds, metal frames, computers, TVs, etc. Electronic devices and

window frames can negatively affect the product’sfunctionality.

•Donot drop the product and do not expose it to any major shocks.

•Donot open the device or continue to operate it if it becomes damaged.

•Donot attempt to service or repair the product yourself.Leave any and all service work to qualied experts.

•Keep the packaging material out of the reach of children due to the risk of suffocation.

•Dispose of packaging material immediately according to locally applicable regulations.

•Donot modify the product in any way.Doing so voids the warranty.

Warning –Batteries

•Immediately remove and dispose of dead batteries from the product.

•Only use batteries (or rechargeable batteries) that match the specied type.

•Donot mix old and new batteries or batteries of adifferent type or make.

•When inserting batteries, note the correct polarity (+ and -markings) and insert the batteries

accordingly.Failuretodosocould result in the batteries leaking or exploding.

•Donot charge batteries.

•Keep batteries out of the reach of children.

•Donot short circuit the batteries/rechargeable batteries and keep them away from uncoated metal

objects.

4. Getting Started

4.1. Measuring station

•Open the battery compartment (46) and insert two AAA batteries with the correct polarity.

•Press the CH-/TX button (43) repeatedly to select the channel the measuring station is to use for

transmission. CH1, CH2 or CH3 is shown on the display.

•Press the °C/°F button (45) to choose between °C and °F for the temperaturedisplay.

•Close the battery compartment.

Note

Beforeuse, ensureyou insert the batteries in the measuring station rst and then in the base station.

4.2. Base station

•Open the battery compartment (40) and insert two AA batteries with the correct polarity.Close the battery

compartment.

5. Installation

Note –Installation

•Werecommend initially placing the base and measuring stations in the intended locations without

installing them and making all the settings described in 6. Operation –todo.

•Only install the stations once the appropriate settings have been made and astable wireless connection

is established.

Note

•The wireless transmission range between the measuring and base stations is up to 30 minopen spaces.

•Beforeinstallation, ensurethat wireless transmission will not be disrupted by interference or obstacles

like buildings, trees, vehicles, high-voltage lines, etc.

•Beforethe nal installation, ensurethat thereissucient reception between the intended installation

locations.

•When installing the measuring station, ensurethat it is protected from direct sunlight and rain.

•The international standardheight for measuring air temperatureis1.25 m(4ft) above ground.

Warning

•Buy special or suitable installation material from aspecialised dealer for wall-mounting.

•Ensurethat no faulty or damaged parts areinstalled.

•Never apply force during installation. This could damage the product.

•Beforeinstallation, ensurethat the chosen wall is suitable for the weight to be mounted, and make sure

that thereare no electrical wires, water,gas or other lines at the installation site on the wall.

5.1. Base station

•Use the base to position the base station on alevel surface.

5.2. Measuring station

•You can also position the measuring station on alevel outdoor surface.

•Werecommend installing the measuring station securely on an outdoor wall using the opening (44).

•Install an anchor,screw,nail, etc. in the wall of your choice.

•Hang up the base/measuring station using the opening intended for this purpose.

6. Operation

Note –Input

Hold down the +button (36) or the –button (37) to select the values faster.

6.1. Initial settings

•After inserting the batteries, avalue indicating the height in metres (4) will ash.

•Set the following information in the order listed:

•height of the location, symbol for the current weather conditions, atmospheric pressureunit (hPa/ inhg)

•Toselect the individual values, press the +button (36) or the –button (37) and conrm each selection by

pressing the HISTORY button (38). .

•The standardsettings areretained if you do not make an entry within 20 seconds. Youcan subsequently

change/reset these values at any time as described in 6.4. Basic and manual settings.

6.2. Connection to the measuring station

•After making initial settings, the base station automatically searches for aconnection to the measuring

station and performs initial setup.

Note

•Initial setup takes approx. 3minutes.

•During connection, the wireless symbol on the measuring station will ash (29).

•Donot press any buttons during setup. Otherwise, values may not be transmitted correctly and thereisa

risk of value errors and inaccuracies.

•The setup process is completed when the indoor (6, 10) and outdoor (22, 28) measurement data is

displayed.

•Ifthe base station still does not receive asignal from the measuring station, press and hold the CHANNEL

button (39)for approx. 3seconds to start the manual search for the signal.

6.3. Selecting the channel/other measuring stations

Note

Youcan install two moremeasuring stations in addition to the included measuring station. Ensurethat the

base and measuring stations areset to the same channel.

Visit www.hama.com for suitable measuring stations.

•Press the CHANNEL button (39)repeatedly to set the channel to that set on the respective measuring

station –see 4.1. Measuring station .1, 2, 3 (30) or Channel overview (24) is displayed.

•The base station now shows the data measured (22, 28) on the selected measuring station (30).

•Select Channel overview (24) to show the measurement values of the individual measuring stations/

channels consecutively for 5seconds each.

6.4. Basic and manual settings

Automatic setting using the DCF signal

•After the rst time the base station is switched on and successful transmission is established between the

base station and the measuring station, the clock will automatically search for aDCF signal. During the

search, the wireless symbol (32) willash.

Display Searching for the DCF signal

Display ashing Active

Displayed continuously Successful –signal is being received

Not displayed Deactivated

•Ifthe station still does not receive asignal, press and hold the +button (27) )and the –button (28) for

approx. 3seconds to start the manual search for the DCF signal. The wireless symbol (5) will start to ash.

Note –Time settings

•The search process takes about 7minutes. If the search fails, it ends and is repeated at the next clock

hour.The wireless symbol (32) will go out.

•Inthe meantime you can, however,set the time and the date manually.

•The clock automatically continues to search for the DCF signal on adaily basis (between 1:00 a.m. and

3:00 a.m.). If the signal is received successfully,the manually-set time and date areoverwritten.

Note –Summer time

•The clock automatically switches to summer time. S(31) appears on the display as long as summer time

is activated.

•Press and hold the +button (36) and the –button (37) again for approx. 3seconds to stop the manual

search.

(Manual) settings

•Press and hold the +button (36) and the –button (37) for approx. 3seconds to stop the search for the

DCF signal. The wireless symbol (32) goes out and you can set the time manually.

•Press and hold the MODE button (35) for approx. 3seconds to make the following settings one after the

other:

•Year (12)

•Month (14)

•Day (13)

•Time zone (12)

•Weekday (20)

•12/24 hour format (12)

•Hours (12)

•Minutes (12)

•Town/City (17)

•Toselect the individual values, press the +button (36) or the –button (37) and conrm each selection by

pressing the MODE button (35).

•Ifyou do not make an entry for 20 seconds, you automatically exit setup mode.

Note –Time zone

•The DCF signal can be received over long distances, but always transmits the current Central European

Time in Germany.Make sureyou account for the time difference in countries with another time zone.

•Ifyou areinMoscow,the time is 3hours later than in Germany.This means that you should set +3 for

the time zone. The clock then automatically sets the time to 3hours after the DCF signal received or

relative to the manually set time.

Note –Weekday

Youcan choose from German (GE), English (EN), Danish (DA), Dutch (DU), Italian (IT), Spanish (SP) or

French (FR) for the weekday display.

Note –Town/City

The sunrise (15) and sunset (18) entry depends on the location. Forthis, select one of the 150 towns/cities

from the list at the end of these operating instructions.

Celsius /Fahrenheit

•Press the –button (37) to switch between °C and °F for the temperaturedisplay.

Alarm

•Repeatedly press the MODE button (35) to access alarm mode 1or2.

•A1orA2isdisplayed accordingly in the seconds display.

•Press and hold the MODE button (35) for approx. 3seconds to set the signal time of the alarm displayed.

The hours display begins to ash.

•Press the +button (36) or the –button (37) to select the hour for the alarm time and conrm your selection

by pressing the MODE button (35). The minutes display begins to ash.

•Repeat the process to set the minutes for the alarm time.

•Press the MODE button (35) repeatedly to also set the other alarm mode or return to the time display (12).

•Ifyou do not make an entry for 20 seconds, you automatically exit setup mode.

Note –Alarm

•When activated, alarm mode 1only triggers an alarm signal on weekdays (Monday to Friday).

•When activated, alarm mode 2only triggers an alarm signal on Saturday and Sunday.

•Inalarm mode 1or2,press the –button (37) to activate/deactivate the corresponding alarm and conrm

your entry by pressing the MODE button (35).

The alarm symbol (27) will appear/not appear.

•Ifthe alarm is triggered, the alarm symbol (27) will begin to ash and an alarm signal willsound.

•Press any button (except the SNOOZE/LIGHT button (34) to stop the alarm. Otherwise, it will stop

automatically after 2minutes.

•Ifyou press the SNOOZE/LIGHT button (34) during the alarm, the alarm is interrupted for 5minutes and

then goes off again. The alarm symbol (27) will ash.

Height/weather forecast/atmospheric pressure unit

•Press and hold the HISTORY button (39) for approx. 3seconds to make the following settings one after

the other:

height of the location, symbol for the current weather conditions, atmospheric pressureunit (hPa/ inhg)

•Toselect the individual values, press the +button (36) or the –button (37) and conrm each selection by

pressing the HISTORY button (38).

Note

•The height at the current location and the current weather form the basis for calculating the atmospheric

pressureand the weather forecast.

•Ifyou should not know the values for these variables, you can nd further information in the Internet,

from the local meteorological oce, on the radio, etc.

•Werecommend that you adapt these values to your location to increase the accuracy of the weather

forecast.

•Aheight of 590 mand slightly cloudy weather areused as standard.

Andere Handbücher für EWS-830

Inhaltsverzeichnis

Andere Hama Wetterstation Handbücher

Hama

Hama EWS Intro Bedienungsanleitung

Hama

Hama EWS-110 Bedienungsanleitung

Hama

Hama TH500 Bedienungsanleitung

Hama

Hama 00186310 Bedienungsanleitung

Hama

Hama EWS-2050 Bedienungsanleitung

Hama

Hama Premium 00186380 Bedienungsanleitung

Hama

Hama EWS-500 Bedienungsanleitung

Hama

Hama EWS-810 Bedienungsanleitung

Hama

Hama i@Sky Bedienungsanleitung

Hama

Hama EWS-3100 Bedienungsanleitung

Hama

Hama Color 00185861 Bedienungsanleitung

Hama

Hama EWS-751 Bedienungsanleitung

Hama

Hama EWS-Trio Bedienungsanleitung

Hama

Hama TH-100 Bedienungsanleitung

Hama

Hama EWS-151 Bedienungsanleitung

Hama

Hama EWS-850 Bedienungsanleitung

Hama

Hama EWS-830 Bedienungsanleitung

Hama

Hama TH50 Bedienungsanleitung

Hama

Hama EWS-Trio Bedienungsanleitung

Hama

Hama TS-200 Bedienungsanleitung

Hama

Hama EWS-890 Bedienungsanleitung

Hama

Hama EWS-152 Bedienungsanleitung

Hama

Hama WFC-970 Bedienungsanleitung

Hama

Hama 99123148 WS-710 Bedienungsanleitung

Beliebte Wetterstation Handbücher anderer Marken

Auriol

Auriol AHFL 433 A1 Bedienungsanleitung

Hyundai

Hyundai WS 2202 Bedienungsanleitung

NexSens

NexSens G2-HYDROMET Bedienungsanleitung

IROX

IROX HBVR761 UV-X Bedienungsanleitung

La Crosse Technology

La Crosse Technology C86371 Bedienungsanleitung

ADE

ADE WS 1711 Bedienungsanleitung

Auriol

Auriol z29592 Bedienungsanleitung

Auriol

Auriol 296289 Bedienungsanleitung

Hyundai

Hyundai WS 2266 Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-2210 Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-811561 Bedienungsanleitung

Ventus

Ventus W177 Bedienungsanleitung

National Geographic

National Geographic VA Colour RC Bedienungsanleitung

Levenhuk

Levenhuk Discovery Report WA40 Bedienungsanleitung

Instant Transmission

Instant Transmission MA 10410 Bedienungsanleitung

Lutron Electronics

Lutron Electronics PHB-318 Bedienungsanleitung

WAREMA

WAREMA EWFS Weather station eco Bedienungsanleitung

TFA

TFA 30.3013.IT Bedienungsanleitung