Harbor Breeze BELLEVUE E-BE44ABZ5C Bedienungsanleitung

E124404

ITEM #0096879

0096950

0096982

0205233

SOS ITEM #0018035

BELLEVUE CEILING FAN

Harbor Breeze® is a registered trademark

Español p. 22

MODEL #E-BE44ABZ5C

E-BE44AN5C

E-BE44MWW5C

E-BE44PPW5C

E-BE44AB5CS

Federal regulations require ceiling fans with light kits manufactured or imported after

January 1, 2009, to limit total wattage consumed by the light kit to 190W. Therefore,

this fan is equipped with a wattage limiting device.

Questions, problems, missing parts? Before returning to your retailer, call or contact our

customer service department at 1-800-527-1292, 8:30 a.m. - 5:00 p.m., CST, Monday - Friday.

ATTACH YOUR RECEIPT HERE

Serial Number Purchase Date

SAFETY INFORMATION

READ AND SAVE THESE INSTRUCTIONS

Please read and understand this entire manual before attempting to assemble, install or operate the

product. If you have any questions regarding the product, please call customer service at

1-800-527-1292, 8:30 a.m. - 5:00 p.m., CST, Monday - Friday.

• Do not discard fan carton or foam inserts. Should this fan need to be returned to the factory for

repairs, it must be shipped in its original packaging to ensure proper protection against damage that

might exceed the initial cause for return.

• Make sure that all electrical connections comply with local codes, ordinances, the National Electrical

Code and ANSI/NFPA 70-1999. Hire a qualified electrician or consult a do-it-yourself wiring handbook

(available at Lowe's) if you are unfamiliar with installing electrical wiring.

• Make sure the installation site you choose allows a minimum clearance of 7 feet from the blades to

the floor and at least 30 in. from the end of the blades to any obstruction.

• After you install the fan, make sure that all connections are secure to prevent the fan from falling.

• The net weight of this fan including the light kit is: 14 lbs. (6.35 kg).

TABLE OF CONTENTS

Safety Information .....................................………………………………………………...…

….....

2 - 3

Product Overview ...........................................................................................................................4

Package Contents .....……………………………………………………………..….

….

.........

......

Hardware Contents ...................................................................................................................

......

Preparation ...............….…………………..……………………….…………….……………….......6

Initial Installation ............….……………..……………………….……….

…..….

.............................7 - 8

Downrod Style Fan Mounting ............................................................................................8 - 10

Closemount Style Fan Mounting

...........................................................................................10 - 11

Wiring .................................……………………........................................…………...........12 - 13

Final Installation ….…………….……………………….…………….……..........

....

….......

14 - 16

Operation Instructions ............................................................……………………

……

….

...........

16 - 18

Care and Maintenance …

….…

…………………………………………………..….......

.....

.......

Troubleshooting .............………...………………………….……………..………....

….......

18 - 19

Warranty ……………………………….…………………………………………..…

….

.........

........

Replacement Parts List ...........................................................................................

.........

......

............

SAFETY INFORMATION

To reduce the risk of fire, electrical shock, or personal injury, mount fan to outlet box

marked "ACCEPTABLE FOR FAN SUPPORT OF 35 LBS (15.9 KG) OR LESS" and use

mounting screws provided with the outlet box. Most outlet boxes commonly used for the

support of lighting fixtures are not acceptable for fan support and may need to be replaced.

Consult a qualified electrician if in doubt.

When mounting fan to a ceiling outlet box, use a METAL octagonal outlet box. Secure the outlet

box directly to the building structure. The outlet box and its support must be able to support the

moving weight of the fan (at least 35 lbs.). Do NOT use a plastic outlet box.

To avoid personal injury, the use of gloves may be necessary while handling fan parts with

sharp edges.

To reduce the risk of fire, electrical shock, or personal injury, wire connectors provided with this

fan are designed to accept only one 12-gauge house wire and two lead wires from the fan. If your

house wire is larger than 12-gauge or there is more than one house wire to connect to the two fan

lead wires, consult an electrician for the proper size wire connectors to use.

To reduce the risk of fire or electrical shock, do not use the fan with any solid state speed

control device or control fan speed with a full range dimmer switch.

To reduce the risk of fire, electrical shock, or personal injury, do not bend the blade arms when

installing them, balancing the blades, or cleaning the fan. Do not insert objects between the

rotating fan blades.

To reduce the risk of personal injury, use only parts provided with this fan. The use of parts

OTHER than those provided with this fan will void the warranty.

WARNINGS

CAUTIONS

Before proceeding, be sure to shut off electricity at main switch or circuit breaker in order to avoid

electrical shock.

Read all instructions and safety information before installing your new fan. Review the

accompanying assembly diagrams.

Congratulations on your purchase of this Harbor Breeze®

Ceiling Fan! This product has been specifically designed to

give you all the performance you’ll ever need. Harbor Breeze®

is the perfect fusion of smart innovation and beautiful style.

Designed for more than just air movement, our products are

built to function flawlessly... day after day. Expect showroom

quality at an exceptional price with Harbor Breeze® - available

exclusively at Lowe’s.

Determining how you want your ceiling fan to look and operate is an important step prior to

installation. You can save installation time by deciding which options are best suited for your needs

before beginning the steps outlined in this manual.

Your fan can be installed with or without a downrod.

• Downrod-style mounting is best suited for ceilings 8 ft. (2.44 m) high or higher. For taller ceillings

you may want to use a longer downrod (sold separately) than the one provided.

• Angle-style mounting is best suited for angled or vaulted ceilings. A longer downrod is sometimes

necessary to ensure proper blade clearance.

• Closemount-style mounting is more suitable for ceilings lower than 8 ft. (2.44 m) high.

Your fan also has multiple wiring options available, including:

• Fan and light controlled by pull chain.

• Fan controlled by pull chain, light controlled by wall switch.

• Fan and light controlled by two separate wall switches.

Your fan is remote control adaptable (remote control sold separately).

Harbor Breeze® is a registered trademark

PRODUCT OVERVIEW

IMPORTANT REMINDER: You must

use the parts provided with this fan for

proper installation and safety.

PART DESCRIPTION QUANTITY

Pull Chain Extension

L Socket Ring (preassembled) 3

M Motor Screw 10

(preassembled)

Lock Washer 10

(preassembled)

Canopy Mounting Screw 4

(preassembled)

Pin (preassembled) 1

Q Clip (preassembled) 1

Star Washer

(preassembled)

S Fitter Plate Screw 3

(preassembled)

PART DESCRIPTION QUANTITY

Downrod

Canopy 1

Mounting Bracket

Motor Housing

E Yoke Cover

F Light Kit Fitter

Blade

Blade Arm

I Glass Shade 3

Candelabra Base Bulb 3

PACKAGE CONTENTS

HARDWARE CONTENTS (shown actual size)

Fiber

Blade

Washer

Qty. 15

BB CC

Blade

Screw

Qty. 15 E3 Wire

Connector

Qty. 4

Before beginning assembly of product, make sure all parts are present. Compare parts with package

contents list and hardware contents above. If any part is missing or damaged, do not attempt to

assemble, the product. Contact customer service for replacement parts.

Estimated Assembly Time: 120 minutes

Tools Required for Assembly (not included): Electrical Tape, Phillips Screwdriver, Pliers, Safety

Glasses, Stepladder and Wire Strippers

Helpful Tools (not included): AC Tester Light, Tape Measure, Do-It-Yourself-Wiring Handbook

(available at Lowe’s) and Wire Cutters

Bulbs Required (included): 3 candelabra-base 60-watt max. bulbs

DANGER: When using an existing outlet box, make sure the outlet box is securely attached to

the building structure and can support the full weight of the fan. Failure to do this can result in serious

injury or death. The stability of the outlet box is essential in minimizing wobble and noise in the fan

after installation is complete.

CAUTION: Be sure outlet box is properly grounded and that a ground wire (green or bare) is

present.

After opening top of carton, remove mounting hardware package from foam inserts. Remove motor

from packing and place on carpet or on foam to avoid damage to ﬁnish.

CAUTION: Carefully check all screws, bolts and nuts on fan motor assembly to ensure that they

are secured.

PREPARATION

INITIAL INSTALLATION

Turn off circuit breakers and wall switch to the fan

supply line leads. (Fig. 1)

DANGER: Failure to disconnect power supply

prior to installation may result in serious injury or

death.

Check to make sure blades (G) are at least 30 in.

from any obstruction. Check downrod (A) length to

ensure blades (G) are at least 7 ft. above the floor.

(Fig. 3)

OFF

Determine mounting method to use. (Fig. 2)

A. Downrod mount (normal or angled ceiling)

B. Closemount (normal ceiling only)

Important:If using the angle mount, check to

make sure the ceiling angle is not steeper than 19°.

7 ft.

min.

30 in.

min.

INITIAL INSTALLATION

DOWNROD STYLE FAN MOUNTING

Remove pin (P) and clip (Q) from downrod (A).

(Fig. 1A)

Partially loosen set screws in motor housing yoke

at top of motor housing (D). (Fig. 1B)

*Helpful Hint: Downrod style mounting is best

suited for ceilings 8 ft. (2.44 m) high or higher. For

taller ceilings you may want to use a longer

downrod (sold separately) than the one provided.

Angle style mounting is best suited for angled or

vaulted ceilings. A longer downrod is sometimes

necessary to ensure proper blade clearance.

Set

Screw

Secure mounting bracket (C) to outlet box using

screws, spring washers, and flat washers

provided with the outlet box. (Fig. 4)

*NOTE:It is very important that you use the

proper hardware when installing the mounting

bracket (C) as this will support the fan.

IMPORTANT: If using the angle mount, make

sure open end of mounting bracket (C) is installed

facing the higher point of the ceiling.

4. 4

Remove motor screws (M) and lock washers (N)

from underside of motor housing (D). Note: Use

opening in fitter plate for easy access to motor

screws (M). [If there are plastic motor blocks

installed with the motor screws (M) and lock

washers (N), discard the plastic motor blocks.]

(Fig. 5)

Follow mounting instructions on pages 8 - 10 for

“Downrod Style Fan Mounting” or proceed to

pages 10 and 11 for “Closemount Style Fan

Mounting”, depending on mounting method (A or

B) chosen in Step 2 on previous page.

1A 1B

Fitter

Plate

DOWNROD STYLE FAN MOUNTING

Depending on the length of downrod (A) you use,

you may need to cut the lead wires back to

simplify the wiring. If you decide to cut back the

lead wires, it is suggested that you do so in the

following manner:

Take the lead wires and make sure that you

have pulled them all the way through the top of

the downrod (A). Start at the TOP of the ball on

the downrod (A) and measure 8 in. of lead wire,

and then cut the excess wire off with wire cutters.

(Fig. 4)

Note: If you do not cut back the lead wires,

Steps 4 and 5 are not necessary and you may

proceed to Step 6 instead.

Ball

Insert downrod (A) through canopy (B) and yoke

cover (E). Thread wires from motor housing (D)

through downrod (A). (Fig. 2)

2. 2

Slip downrod (A) into motor housing yoke, align

holes and re-install pin (P) and clip (Q).

Re-tighten set screws in motor housing yoke

and then tighten nuts. Slide yoke cover (E) down

until it rests on top of motor housing (D). (Fig. 3)

CLOSEMOUNT STYLE FAN MOUNTING

Remove canopy cover from bottom of canopy (B).

[Note: It may be necessary to use the handle end

of a screwdriver to remove the canopy cover by

tapping on the canopy cover from the inside of the

canopy.] (Fig. 1)

*Helpful Hint: Close style mounting is more

suitable for ceilings lower than 8 ft. (2.44 m) high.

The downrod (A), hanging ball, yoke cover (E), and

canopy cover are not used in this type of

installation.

Install ball end of downrod (A) into mounting

bracket (C) opening. Align slot in ball with tab

in mounting bracket (C). (Fig. 6)

DANGER: Failure to align slot in ball with

tab may result in serious injury or death.

Continue to “Wiring” instructions on page 12.

DOWNROD STYLE FAN MOUNTING

If you decided to cut back the lead wires in Step

4, strip 1/2 in. of insulation from end of white

wire. Twist stripped ends of each strand of wire

within the insulation with pliers. (Fig. 5) Repeat

Step 5 for black, blue (if applicable) and green

wires.

Hanging

Ball Slot

Tab

Canopy

Cover

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Harbor Breeze Lüfter Handbücher

Harbor Breeze

Harbor Breeze NAVIN 41555 Bedienungsanleitung

Harbor Breeze

Harbor Breeze BELLHAVEN II E-BLHII52VPW5C4S Bedienungsanleitung

Harbor Breeze

Harbor Breeze TG44BNK3D1RC Bedienungsanleitung

Harbor Breeze

Harbor Breeze LARALYN LRN32 Bedienungsanleitung

Harbor Breeze

Harbor Breeze E-BDB52ABZC5BC4N Bedienungsanleitung

Harbor Breeze

Harbor Breeze Santa Ana LP8294LBN Bedienungsanleitung

Harbor Breeze

Harbor Breeze CENTREVILLE 40117 Bedienungsanleitung

Harbor Breeze

Harbor Breeze CHESHIRE II CSD52FBZ5C4S Bedienungsanleitung

Harbor Breeze

Harbor Breeze CE-JP13EB6RC Bedienungsanleitung

Harbor Breeze

Harbor Breeze BTH44ABZC5C Bedienungsanleitung

Harbor Breeze

Harbor Breeze BUILDER'S SERIES 40698 Bedienungsanleitung

Harbor Breeze

Harbor Breeze 42612 Bedienungsanleitung

Harbor Breeze

Harbor Breeze RLC52WW5C1R Bedienungsanleitung

Harbor Breeze

Harbor Breeze WINDRISE E-TLEII44BNK5C1 Bedienungsanleitung

Harbor Breeze

Harbor Breeze 873 Bedienungsanleitung

Harbor Breeze

Harbor Breeze CLASSIC STYLE 00819 Bedienungsanleitung

Harbor Breeze

Harbor Breeze CPW1413 Bedienungsanleitung

Harbor Breeze

Harbor Breeze STONECROFT 41946 Bedienungsanleitung

Harbor Breeze

Harbor Breeze BDB52ABZC5P Bedienungsanleitung

Harbor Breeze

Harbor Breeze Casual-3-2011 Bedienungsanleitung

Harbor Breeze

Harbor Breeze Calera Bedienungsanleitung

Harbor Breeze

Harbor Breeze 00892 Bedienungsanleitung

Harbor Breeze

Harbor Breeze BOD52MW3 Bedienungsanleitung

Harbor Breeze

Harbor Breeze MONTCLAIR E-CM54RBZ5CRCI Bedienungsanleitung

Beliebte Lüfter Handbücher anderer Marken

ELTA FANS

ELTA FANS H03VV-F Bedienungsanleitung

Hunter

Hunter 20714 Gebrauchsanweisung

Emerson

Emerson CARRERA VERANDA CF542ORB00 Bedienungsanleitung

Hunter

Hunter Caraway Gebrauchsanweisung

Panasonic

Panasonic FV-15NLFS1 Bedienungsanleitung

Kompernass

Kompernass KH 1150 Bedienungsanleitung

VES

VES FALA100/12V/TR Bedienungsanleitung

Vertiv

Vertiv Liebert DCD Bedienungsanleitung

Westinghouse

Westinghouse GFP Series Bedienungsanleitung

Venmar

Venmar KUBIX HRV PLUS Series Bedienungsanleitung

Maico

Maico ECR 31 Bedienungsanleitung

Sonnenkonig

Sonnenkonig Dinky Bedienungsanleitung

S&P

S&P ECOWATT HXBR Bedienungsanleitung

Wider

Wider IMP03369BH Bedienungsanleitung

Panasonic

Panasonic F-60DHN Bedienungsanleitung

Hinkley

Hinkley HIGHLAND Bedienungsanleitung

Broan

Broan 766BN Bedienungsanleitung

Premium

Premium PFS16022 Montageanleitung