Harman Accentra 52i Bedienungsanleitung

Accentra 52i Pellet Insert Zero Clearance Cabinet

Part #1-00-574323

R:\Todd\Instruction Sheets_3-89-574323_RevF

www.harmanstoves.com

Accentra 52i Pellet Insert ZC Cabinet

Accentra 52i Pellet Insert Mounting Frame

Accentra 52i Pellet Insert

Accentra 52i Pellet Insert Zero Clearance Cabinet

Part #1-00-574323

Contents of Kit;

Cabinet components-

1- Top Panel

1- Bottom Panel

2- Side Panels

1- Rear Panel

32- #10 X 3/4” Tek Screws (Self-Tapping)

4- 1/4-20 x 5/8 Thread Cutters

Tools Needed;

Cordless Drill or Screw gun

5/16” Driver Bit

3/8” Driver Bit

CAUTION! Use care when installing Tek screws,

do not strip the holes.

• Beginwiththebottompanellyingatontheooror

workbench. Place it with the writing facing upward

as shown.

• Standasidepaneluptotherightorleftsideofthe

bottom. Notice the bend at the rear of the cabinet

will make the corner and at the front it will be bent

outward to make the facing ange. Line up the

holes and secure the side panel to the bottom with

(3) Tek screws. Repeat for the opposite side. Figure

NOTE: Only install 3 Tek screws.

• Thetoppanelcannowbeputintoplace,withthe

bend going out over the side panels. Align the holes

and secure with (6) Tek screws. Figure 2.

• Standtherearpaneluptotherearofthecabinet

making sure the holes on the edge of the panel

line up with the holes from the side panels and top.

Secure the rear panel to the outside of the cabinet

using the remaining (20) Tek screws. Figure 3.

Figure 1 Figure 2

Figure 3

1/4-20 x 5/8

Thread Cutters

Accentra 52i Pellet Insert Zero Clearance Cabinet

Part #1-00-574323

11 13/16

27 3/8

16 3/4

27 13/16

5 1/25 1/2

16 13/16

29 1/2

29 1/16

31 7/16

28 1/8

16 13/16

Notice the thickness of the ZC



NOTE: When Fiberglass insulation is placed directly on top of the ZC

Cabinetitshouldnottouchthepipe.Theouterringknockoutoftheuepipe

opening is designed to install a standard 6” sheetmetal starter collar and

a short length of pipe to keep the insulation from touching the vent pipe.







   



Accentra 52i Pellet Insert Zero Clearance Cabinet

Part #1-00-574323

TheangesARENOTdesignedtosupporttheweightofthecabinet

andtheAccentraInsert.Theyareonlytosecurecabinettothewall

framing. Adequate framing under the hearth and ZC cabinet MUST

be provided.

Thenishedfaceofthereplacefacade

“MUST” be ush with the ZC Cabinet

front face when completed.

NOTE: See the following pages

for rough-in instructions for other

facing materials.

ZCCabinetrough-inanges

Accentra 52i Pellet Insert Zero Clearance Cabinet

Part #1-00-574323

CautionshouldbetakenNOTTOHAVEastudwithin5”ofthecenterline

oftheuepipe.(UsePLVentPipeONLY)

ThisshouldallowroomforanyPLVentcertiedwallpassthrough.

The nished face of the replace facade, “MUST” be ush with the ZC

Cabinet front face when completed.

NOTE: See following pages for rough-in

instructions for other facing materials.

NOTE: When berglass insulation is

placeddirectlyontopoftheZCCabinet

it should not touch the vent pipe. The

outer ring knock out of the ue pipe

opening is designed to install a standard

6” sheet metal starter collar and a short

length of pipe to keep the insulation from

touching the vent pipe.

Accentra 52i Pellet Insert Zero Clearance Cabinet

Part #1-00-574323

28-3/16”

29-9/16”





Accentra 52i Pellet Insert Zero Clearance Cabinet

Part #1-00-574323

Flue Pipe Rough-in Support Kit #1-00-574246

Harman® Vent Pipe Stub for 3” PL Vent Pipe #1-00-674039

Harman® Vent Pipe Stub for 4” PL Vent Pipe #1-00-574034

Drill #10x3/4 Tek Screws

Precut Alignment Hole

(4) 1/4-20 x 5/8 thread cutters

hold the starter collar into

place until the Accentra 52i

mounting frame is installed.

Drill #10x3/4 Tek Screws

Pre-cut alignment holes for the outside air rough-in.

A second rough-in support #1-00-574246 is used for the outside air rough in. The 3” flex pipe starter stub

is part of kit #1-00-674039.

Accentra 52i Pellet Insert Zero Clearance Cabinet

Part #1-00-574323

There are 4 holes located in the bottom of the

cabinet that match the holes in the mounting

frame of the insert. They are to be used to

secure the insert mounting frame into the

cabinet after rough-in has been complete.

There are 4 cabinet mounting holes in

thebottomthatgoallthewaythrough

the base of the cabinet. These holes

allow the installer to secure the

cabinet to the hearth sub framing.

    



   







Accin 52i Mounting Frame

Accentra 52i Pellet Insert Zero Clearance Cabinet

Part #1-00-574323

3”

12”

36”

12”

Min

MinimumFlueConguration.

3”or4”PLVentPipe

Clearancetoshrubbery,grass,

oranyothertypeplant

Minimumclearanceof ue

outlet to ground level

Excessivemulchandorothertypesofcombustible

bedding should be kept to a minimum directly

beneaththeueoutletarea.

Combustible materials are allowed to

touch the outside of the ZC Cabinet.

PLVentmanufactureswall

pass-through.

NOTE: When berglass insulation is placed

directlyontopoftheZCCabinetitshouldnottouch

theventpipe.Theouterringknockoutoftheue

pipe opening is designed to install a standard 6”

sheetmetal starter collar and a short length of pipe

to keep the insulation from touching the vent pipe.

Thenished face ofthe replace

facade,MUSTbeushwiththeZC

Cabinet front face when complete.

Rough-In Support Kit

Harman®#1-00-574246

Finishedoorprotection

Because of the weight of the Accentra 52i, if raised hearth

is framed, heavier framing and support should be utilized.

Suggested minimum of 2X6’s in 12” centers under the ZC

Cabinet and the hearth in front of the Cabinet.

Accentra 52i Pellet Insert Zero Clearance Cabinet

Part #1-00-574323

3" MIN.

Flashing

Storm Collar 12" MIN.

No insullation or other

combustible materials

are allowed within 3” of

the PL Vent Pipe.

Unless specified by the

pipe manufacturer

PL Vent manufacturer’s firestop

space and support

VentingclearancesforinroominstallationoftheZeroClearanceCabinet.

NOTE:

•IllustrationsreecttypicalinstallationsandareFORDESIGNPURPOSESONLY.

•Illustrations/diagramsarenotdrawntoscale.

•Actualinstallationmayvaryduetoindividualdesign.

NOTE:

InCanada,wherepassagethroughawallorpartitionofcombustibleconstruction

isdesired,theinstallationshallconformtoCAN/CSA-B365.

Andere Handbücher für Accentra 52i

Andere Harman Kamin im Innenbereich Handbücher

Harman

Harman 300i Bedienungsanleitung

Harman

Harman Accentra 52i Pellet Insert Bedienungsanleitung

Harman

Harman Accentra Pellet Insert Montageanleitung

Harman

Harman Accentra Montageanleitung

Harman

Harman TL 2.6 Bedienungsanleitung

Harman

Harman The Serenity III HB 38 DV Montageanleitung

Harman

Harman 300i Montageanleitung

Harman

Harman TL 2.6 Bedienungsanleitung

Harman

Harman Magnafire Series Coal StovesMark I Bedienungsanleitung

Harman

Harman P35I Bedienungsanleitung

Harman

Harman Accentra52i-TC Bedienungsanleitung

Harman

Harman P35i-C Bedienungsanleitung

Harman

Harman P35I Sicherheitsleitfaden

Harman

Harman Accentra Pellet Insert Montageanleitung

Harman

Harman 300i Montageanleitung

Harman

Harman TL2.0 Bedienungsanleitung

Harman

Harman Accentra Pellet Insert Montageanleitung

Harman

Harman Magnafire Elite Coal Montageanleitung

Harman

Harman Accentra 52i Bedienungsanleitung

Harman

Harman P35I Bedienungsanleitung

Harman

Harman Accentra52i-TC Bedienungsanleitung

Beliebte Kamin im Innenbereich Handbücher anderer Marken

Brigantia

Brigantia 35-DVRS31N-2 Betriebsanleitung

Nordpeis

Nordpeis Bergen Bedienungsanleitung

Superior

Superior BCT2536TMN Bedienungsanleitung

Quadra-Fire

Quadra-Fire 5100I-GD-B Bedienungsanleitung

Renaissance

Renaissance RUMFORD 1000 Bedienungsanleitung

Lacunza

Lacunza IV-800 Bedienungsanleitung

Baxi

Baxi 940 Gebrauchsanweisung

Dru

Dru Maestro 60/2 Tall RCH Bedienungsanleitung

Diamond Fireglass

Diamond Fireglass SS-O22 Bedienungsanleitung

HearthStone

HearthStone Windsor Bay 8830 Programmierhandbuch

Napoleon

Napoleon ASCENT B42 Bedienungsanleitung

Enviro

Enviro E33GI Bedienungsanleitung

Smeg

Smeg L30 FABE Montageanleitung

KEDDY

KEDDY K700 Bedienungsanleitung

Godin

Godin 3451 Bedienungsanleitung

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Bedienungsanleitung

Desa

Desa CCFPDFT Bedienungsanleitung

Miles Industries

Miles Industries Vogue 1300IRN Handbuch