Harman P35i-C Bedienungsanleitung

Harman® • P35i-C Installation Manual_R2 • 2019 -___ • 02/2018390-784i

Installation Manual

Installation and Appliance Setup

INSTALLER: Leave this manual with party responsible for use and operation.

OWNER: Retain this manual for future reference.

To obtain a French translation of this manual, please

contact your dealer or visit www.harmanstoves.com

Pour obtenir une traduction française de ce manuel, s’il

vous plaît contacter votre revendeur ou visitez www.

harmanstoves.com

NOTE

Model(s):

P35i-C Pellet Insert

NOTICE: SAVE THESE INSTRUCTIONS

Please read this entire manual before

installation and use of this pellet fuel-

burning room heater.

Failure to follow these instructions could

result in property damage, bodily injury

or even death.

• Donotstoreorusegasolineorotherammablevapors

and liquids in the vicinity of this or any other appliance.

• Donotoverre-Ifanyexternalpartstartstoglow,you

areoverring.Reducefeedrate.Overringwillvoid

your warranty.

• Comply with all minimum clearances to combustibles

asspecied.Failuretocomplymaycausehousere.

WARNING

Hot glass will cause burns.

• Do not touch glass until it is cooled

• NEVERallowchildrentotouchglass

• Keep children away

• CAREFULLYSUPERVISEchildreninsameroomas

stove.

• Alert children and adults to hazards of high temperatures.

High temperatures may ignite clothing or other

ammable materials.

• Keepclothing,furniture,draperiesandotherammable

materials away.

HOT SURFACES!

Glass and other surfaces are hot during

operation and cool down.

WARNING

Tested and approved for wood pellets only burning of

any other type of fuel voids your warranty. When burning

higher ash content pellets more frequent cleanings may

be required.

CAUTION

Check building codes prior to installation.

• InstallationMUSTcomplywithlocal,regional,stateand

national codes and regulations.

• Contactlocalbuildingorreo󰀩cialsaboutrestrictions

and installation inspection requirements in your area.

CAUTION

Harman® • P35i-C Installation Manual_R2 • 2019 -___ • 02/2028390-784i

= Contains updated information

TABLE OF CONTENTS

Safety Alert Key:

• DANGER! Indicatesahazardoussituationwhich,ifnotavoidedwill result in death or serious injury.

• WARNING!Indicatesahazardoussituationwhich,ifnotavoidedcould result in death or serious injury.

• CAUTION! Indicatesahazardoussituationwhich,ifnotavoided,couldresultinminorormoderateinjury.

• NOTICE:Indicatespracticeswhichmaycausedamagetothestoveortoproperty.

InstallationStandardWorkChecklist....................3

1 Product Specic and Important Safety Information

A. ApplianceCertication ............................4

B. GlassSpecications..............................4

C. MobileHomeApproved ...........................4

D. BTU&E󰀩ciencySpecications ..................... 4

E. Non-CombustibleMaterialsSpecication. . . . . . . . . . . . . . 5

F. CombustibleMaterialsSpecication .................5

G. Electrical Codes ................................. 5

H. California ......................................5

2 Getting Started

A. DesignandInstallationConsiderations ...............6

B. ToolsandSuppliesNeeded ........................7

C. InspectApplianceandComponents..................7

3 Clearances

A. Appliance Dimension Diagram ......................8

B. ClearancestoCombustibles&FloorProtection. . . . . . . . . 9

C. MinimumOpening-Masonry&ManufacturedFireplaces . 9

4 Termination Location and Vent Information

A. Vent Termination Design .........................10

B. Venting&UseofElbows .........................14

C. BatteryBack-upPower. . . . . . . . . . . . . . . . . . . . . . . . . . . 15

D. OutsideAir ....................................16

E. LocatingYourApplianceandChimney...............16

F. Negative Pressure ..............................17

G.AvoidingSmoke&Odors .........................17

H. MobileHomeInstallation .........................19

I. FireSafety ....................................20

J. InspectAppliance&Components .................. 20

5 Appliance Setup

A. UnpackingUnit.................................21

B. ControlBoardInstallation.........................22

C. SecuringMountingFrame ........................22

D. RoutingthePowerCord..........................22

E. InstallingtheVenting ............................23

F. InstallingtheBodyintotheMountingFrame ..........23

G.RoomSensorInstallation .........................23

H. FlameGuideExtension ..........................24

I. FireboxDraftandCombustionFanRPM .............25

6 Reference Materials

A. SafetyReminders...............................26

B. Wiring Diagram.................................27



Harman® • P35i-C Installation Manual_R2 • 2019 -___ • 02/2038390-784i

Installation Standard Work Checklist

ATTENTION INSTALLER:

Follow this Standard Work Checklist

This standard work checklist is to be used by the installer in conjunction with, not instead of, the instructions contained in

this installation manual.

Customer: ________________________________ Date Installed: __________________________

Lot/Address: ________________________________ Location of Stove: __________________________

________________________________ Installer: __________________________

Model: ________________________________ Dealer/Distributer Ph #__________________________

Serial Number: __________________________

WARNING! Risk of Fire or Explosion! Failure to install appliance to these instructions can lead to a re

or explosion.

Appliance Install Section 3 YES IF NO, WHY?

Required non-combustible oor protection ________________________________

Veried clearances to combustible. ________________________________

Unit is Leveled and secured. ________________________________

Venting/Chimney Section 4

Venting Conguration complies to vent diagrams. ________________________________

Venting installed, sealed and secured in place with proper clearances. ________________________________

Exterior wall/roof ashing installed and sealed ________________________________

Terminations installed and sealed. ________________________________

Electrical Section 1

120 VAC unswitched power provided to the appliance. ________________________________

Check outlet with multi-meter for proper voltage. (115-120 VAC) ________________________________

Record voltage reading: ___________

Appliance Setup Section 5

All packaging and protective materials are removed ________________________________

Accessories installed properly ________________________________

Manual bag and all it’s contents are removed from inside the appliance

and given to party responsible for use and operation ________________________________

Started appliance and veried that all motors and blowers operate

as they should. ________________________________

Checked draft using a Manometer. Record readings: __________ ________________________________

Hearth and Home Technologies recommends the following:

Photographing the installation and copying this checklist for your le.

This checklist remain visible at all times on the appliance until the installation is complete.

Comments: Further description of the issues, who is responsible (Installer/Builder/Other Trades, etc.) and corrective action

needed __________________________________________________________________________________________

_________________________________________________________________________________________________

Comments communicated to party responsible____________________ by ________________________ on __________

(Builder / Gen Contractor) (Installer) (Date)

04/17

Harman® • P35i-C Installation Manual_R2 • 2019 -___ • 02/2048390-784i

A. Appliance Certication

B. Glass Specications

This appliance is equipped with 5mm ceramic glass.

Replaceglassonlywith5mmceramicglass.Pleasecontact

your dealer for replacement glass.

C. Mobile Home Approved

This appliance is approved for mobile home installations

when not installed in a sleeping room and when an outside

combustion air inlet is provided.

The appliance must be properly grounded to the frame of

the mobile home using a minimum of 8 AWG copper solid or

stranded, insulated or bare wire or equivalent and use only

listedpelletvent,Class“PL”connectorpipe.

A Harman® OutsideAir Kit must be installed in a mobile

home installation.

NOTE: This installation must conform with local codes.

Intheabsenceoflocalcodesyoumustcomplywiththe

ASTME1509-12,ULC-S628-93& (UM) 84-HUD

MODEL: P35i-CPelletInsert

LABORATORY: OMNI-TestLaboratories,Inc.,PFS-TECO

REPORT NO. 135-S-25-6.2,0135PN025S,F19-531

TYPE: PelletFueledInsert/Supplementary

ForResidentialUse

STANDARD(s): ASTME1509-12(2017),ULC-S628-00,

ASTME2515-11,ASTME2779-10

D. BTU & E󰀩ciency Specications

11 Product Specic and Important Safety Information

The P35i-C Pellet Insert is certied to

comply with 2020 EPA particulate emission

standards.

*Weighted average LHV e󰀩ciency using data collected

during EPA emissions test.

**Weighted average HHV e󰀩ciency using data collected

during EPA emissions test.

***ArangeofBTUoutputsbasedonEPADefaultE󰀩ciency

and the burn rates from the low and high EPA tests.

****Basedonthemaximumfeedrateperhourmultipliedby

approximately8600BTU’swhichistheaverageBTU’sfrom

a pound of pellets.

Thiswoodheaterhasamanufacturer-setminimumlowburn

ratethatmustnotbealtered.Itisagainstfederalregulations

to alter this setting or otherwise operate this wood heater

in a manner inconsistent with operating instructions in this

manual.

This wood heater needs periodic inspection and repair for

properoperation.Itisagainstfederalregulationstooperate

this wood heater in a manner inconsistent with operating

instructions in this manual.

EPA Certication Number:

EPA Certied Emissions: 1.5g/hr

*LHV Tested E󰀩ciency: 74.2%

**HHV Tested E󰀩ciency: 68.2%

***EPA BTU Output: 9,600-28,800

****BTU Input 12,800-38,400

Vent Size: 4Inch

Hopper Capacity: 62 lbs

Fuel Wood Pellet

Note: This installation must conform with local codes.

Intheabsenceoflocalcodesyoumustcomplywiththe

ASTM E 1509-2012, ULC S628-93, (UM) 84-HUD

Note: Hearth&HomeTechnologies,manufacturerofthis

appliance, reserves the right to alter its products, their

specicationsand/orpricewithoutnotice.

Harman® is a registered trademark of Hearth & Home

Technologies.

Note: Somegeneratororbatteryback-upsystemsmay

not be compatible with the micro-processor electronics

on this appliance. Please consult the power supply

manufacturer for compatible systems.

THE STRUCTURAL INTEGRITY OF THE

MANUFACTURED HOME FLOOR, WALL, AND

CEILING/ROOF MUST BE MAINTAINED.

DO NOT INSTALL IN SLEEPING ROOM.

CAUTION

Harman® • P35i-C Installation Manual_R2 • 2019 -___ • 02/2058390-784i

E. Non-Combustible Materials Specication

Materialwhichwillnotigniteandburn.Suchmaterialsare

those consisting entirely of steel, iron, brick, tile, concrete,

slate, glass or plasters, or any combination thereof.

Materials that are reported as passing ASTM E 136,

Standard Test Method for Behavior of Materials in

a Vertical Tube Furnace at 750º C and UL763 shall be

considerednon-combustiblematerials.

F. Combustible Materials Specication

Materials made of or surfaced with wood, compressed

paper,plantbers,plastics,orothermaterialthatcanignite

and burn, whether ame proofed or not, or plastered or

unplastered shall be considered combustible materials.

G. Electrical Codes

120VAC,60Hz,Start5.0Amps,Run4.0Amps

Note: Some generator or battery back-up systems may

not be compatible with the micro-processor electronics

on this appliance. Please consult the power supply

manufacturer for compatible systems.

WARNING! Risk of Fire! Hearth & Home Technologies

disclaims any responsibility for, and the warranty and agency

listing will be voided by the below actions.

DO NOT:

• Install or operate damaged appliance

• Modify appliance

• Install other than as instructed by Hearth & Home

Technologies

• Operate the appliance without fully assembling all

components

• Overre

• Install any component not approved by Hearth & Home

Technologies

• Install parts or components not Listed or approved.

• Disable safety switches

Improper installation, adjustment, alteration, service or

maintenance can cause injury or property damage.

Forassistanceoradditionalinformation,consultaqualied

installer, service agency or your dealer.

NOTE: Hearth & Home Technologies, manufacturer of

this appliance, reserves the right to alter its products, their

specicationsand/orpricewithoutnotice.

Harman® is a registered trademark of Hearth & Home

Technologies.

!WARNING

This product and the fuels used to operate this product

(wood),andtheproductsofcombustionofsuchfuels,can

expose you to chemicals including carbon black, which

isknownto theStateofCalifornia tocausecancer,and

carbonmonoxide,whichisknowtotheStateofCalifornia

to cause birth defects or other reproductive harm. For

more information go to: www.P65Warnings.ca.gov

H. California

Harman® • P35i-C Installation Manual_R2 • 2019 -___ • 02/2068390-784i

Design and Installation Considerations

1. Appliance Location

NOTICE: Check building codes prior to installation.

• InstallationMUSTcomplywithlocal,regional,stateand

national codes and regulations.

• Consult insurance carrier, local building inspector, re

o󰀩cialsorauthoritieshavingjurisdictionoverrestrictions,

installation inspection and permits.

Itisagoodideatoplanyourinstallationonpaper,usingexact

measurementsfor clearances andoor protection, before

actually beginning the installation

Consideration must be given to:

• Safety,convenience,tra󰀩cow

• Placement of the chimney and chimney connector.

• If you are not using an existing chimney, place the

appliance where there will be a clear passage for a

factory-builtlistedchimneythroughtheceilingandroof.

• Installing an optional outside air kit would a󰀨ect the

location of the vent termination.

Suitable replaces for installation:

• MasonryFireplace

• ExistingFactoryBuiltWoodBurningFireplace

• Harman®ZeroClearanceCabinet-Part#1-00-574323

EXCEPTION:Masonryorsteel,includingthedamperplate,

may be removed from the smoke shelf and adjacent damper

frame if necessary to accommodate a chimney liner,

Marginal Location:

• Below peak

Location NOT recommended:

• Not the highest point of the roof

• Wind loading possible

Multi-level Roofs

Windward

Leeward

Recommended:

Outside Air Intake

on windward side

NOT recommended:

Outside Air Intake

on leeward side

Recommended Location:

• Above peak

Recommended:

• Insulated exterior chase

in cooler climates

Recommended Location:

• Above peak

• Inside heated space

Location NOT recommended:

• Too close to tree

• Below adjacent structure

• Lower roof line

• Avoid outside wall

Marginal Location:

• Wind loading possible

Figure 2.1

22 Getting Started

provided that their removal will not weaken the structure of

the replace and chimney, and will not reduce protection

for combustible materials to less than that required by the

National Building Code.

Sincepelletexhaustcancontainash,sootorsparks,you

must consider the location of:

• Windows

• AirIntakes

• Air Conditioner

• Overhangs,so󰀩ts,porchroofs,adjacentwalls

• Landscaping,vegetation

When locating vent and venting termination, vent above

roof line when possible.

Warning! Risk of Fire Damaged parts could impair safe

operation. Do NOT install damaged, incomplete or substitute

components.

NOTICE: Locating the appliance in a location of considerable

air movement can cause intermittent smoke spillage from

appliance. Do not locate appliance near:

• Frequently open doors

• Central heat outlets or returns

Installation and service of this

appliance should be performed by

qualiedpersonnel.Hearth&Home

Technologies recommends HHT

Factory Trained or NFI Certied

professionals.

Harman® • P35i-C Installation Manual_R2 • 2019 -___ • 02/2078390-784i

ReciprocatingSaw

Hammer

PhillipsScrewdriver

TapeMeasure

Level

Non-CombustibleSealant

Material

Gloves

SafetyGlasses

ElectricDrill&Bits

May also need:

VentSupportStraps

Venting Paint

Tools and building supplies normally required

for installation, unless installing into an existing

masonry replace:

B. Tools And Supplies Needed

C. Inspect Appliance and Components

• Carefully remove the appliance and components from the

packaging.

• The vent system components and decorative doors and

fronts may be shipped in separate packages.

•  Ifoptionallogsetispurchased,thelogbracketmustbe

installed prior to installing the log set.

•  Report to your dealer any parts damaged inshipment,

particularly the condition of the glass.

• Read all of the instructions before starting the

installation. Follow these instructions carefully during

the installation to ensure maximum safety and benet.

Hearth&HomeTechnologiesdisclaimsanyresponsibility

for, and the warranty will be voided by, the following

actions:

•  Installationanduseofanydamagedapplianceorvent

system component.

•  Modicationoftheapplianceorventsystem.

•  InstallationotherthanasinstructedbyHearth&Home

Technologies.

•  Installation and/or use of any component part not

approvedbyHearth&HomeTechnologies.

Any such action may cause a re hazard.

Risk of Fire, Explosion or Electric Shock!

DO NOT use this appliance if any part has

been under water. Call a qualied service

technician to inspect the appliance and to

replace any part of the control system that

has been under water.

WARNING

RISK OF FIRE OR EXPLOSION! Damaged

parts could impair safe operation. DO NOT

install damaged, incomplete or substitute

components. Keep appliance dry.

Harman® • P35i-C Installation Manual_R2 • 2019 -___ • 02/2088390-784i

33 Clearances

A. Appliance Dimension Diagram

Dimensionsareactualappliancedimensions.Useforreferenceonly.

Figure 3.1

14”

356mm

22”

559mm

8”

203mm

10”

254mm

2”

50mm

Standard Surround

#1-00-774221

Oversized Surround

#1-00-774250

A40"(1016mm) 46"(1168mm)

B31"(787mm) 34"(864mm)

24”

610mm

23-3/4”

603mm

19-1/2” (495mm)

Hopper

23-1/2” (597mm)

Hopper

9-1/4” (235mm)

Glass

Harman® • P35i-C Installation Manual_R2 • 2019 -___ • 02/2098390-784i

When selecting a location for the appliance it is important to

considertherequiredclearancestowalls(seeFigure3.2).

WARNING! Risk of Fire or Burns! Provide adequate

clearance around air openings and for service access. Due

to high temperatures, the appliance should be located out of

tracandawayfromfurnitureanddraperies.

NOTICE: IllustrationsreecttypicalinstallationsandareFOR

DESIGNPURPOSESONLY.Illustrations/diagramsarenot

drawn to scale. Actual installation may vary due to individual

design preference.

B. Clearances to Combustibles & Floor Protection

*Floorprotectionmustbeusedfromhearthopeningto6"(152mm)infrontofdoorglassand6"(152mm)toeachside

ofthestovebodyOR8”(203mm)tosidestoprotectcombustiblesfromhotashes.Aminimumsizewillbe8-7/8"deep

by24-5/8"wideandbemadeofanon-combustiblematerialormeetULapproval.

Figure 3.2

Location Inches Millimeters

FMinimumWidth 24 609

GMinimumDepth 14-1/2 368

HMinimumHeight#1-70-774235 23-1/2 597

HMinimumHeight#1-70-774195 19-1/2 495

C. Minimum Opening - Masonry and Manufactured Fireplaces

Mantel

Side Wall

Face Trim

Location Inches Millimeters

AInserttocombustiblesidewall 13 330

BSurroundtoptofacetrim 0 0

CSurroundsidetofacetrim 1 25

DInserttopto(max)12"mantel 12 305

EDoor opening to front 6 152

FDoor opening to side 6 152

Harman® • P35i-C Installation Manual_R2 • 2019 -___ • 02/2010 8390-784i

44 Termination Location and Vent Information

A. Venting Termination Design #1 Installing into an existing replace chimney

Thismethodprovidesexcellentventingwith100%outsideair

whichisthemoste󰀩cientoperationofthisunit.Thismethod

also provides natural draft in the event of a power failure.

A4”stainlesssteelexpipeisneededfortheuepipe,and3"

aluminumorStainlessSteelFlexPipeisusedfortheintake.

CHIMNEY CONNECTOR PIPE MAY NOT PASS

THROUGH CONCEALED SPACES INCLUDING AN

ATTIC, ROOF SPACE, CLOSET, FLOOR OR CEILING.

Heightofexistinghearth

#2 Installing into an existing replace chimney

Thismethodprovidesexcellentventingfornormaloperation.

This method also provides natural draft in the event of a

power failure.

A cap should be installed on the chimney to keep out rain.

Combustion air is provided from the living area and enters the

feed system from around the wing and stove body spaces.

The chimney top must be capped to

prevent rain and/or snow from entering

the chimney.

See Figure 4.8, for information on the

optional Harman®Adjustable Stainless

SteelIntakeExtension.

The damper area must be sealed with a

steel plate and it is recommended that

Kaowoll, mineral wool, or an equivalent

non-combustible insulation be placed

on top of the sealed area to reduce the

possibility of condensation. Insulation

alone should not be used to seal the

damper opening. For quick and easy

installation, purchase the steel Harman

BlockO󰀨Plate,1-00-25625.

The chimney top must be capped to

prevent rain and/or snow from entering

the chimney.

The damper area must be sealed with a

steel plate and it is recommended that

Kaowoll, mineral wool, or an equivalent

non-combustible insulation be placed

on top of the sealed area to reduce the

possibility of condensation. Insulation

alone should not be used to seal the

damper opening. For quick and easy

installation, purchase the steel Harman

BlockO󰀨Plate,1-00-25625.

Figure 4.1

Figure 4.2

DO NOT REMOVE BRICKS OR MORTAR FROM THE

EXISTING FIREPLACE.

DO NOT REMOVE BRICKS OR MORTAR FROM THE

EXISTING FIREPLACE.

WARNING

Andere Handbücher für P35i-C

Inhaltsverzeichnis

Andere Harman Kamin im Innenbereich Handbücher

Harman

Harman 300i Montageanleitung

Harman

Harman TL2.0 Bedienungsanleitung

Harman

Harman P35I Sicherheitsleitfaden

Harman

Harman P35I Bedienungsanleitung

Harman

Harman Accentra Pellet Insert Montageanleitung

Harman

Harman 300i Montageanleitung

Harman

Harman TL 2.6 Bedienungsanleitung

Harman

Harman The Serenity III HB 38 DV Montageanleitung

Harman

Harman Accentra 52i Bedienungsanleitung

Harman

Harman Magnafire Elite Coal Montageanleitung

Harman

Harman Accentra Montageanleitung

Harman

Harman Accentra 52i Pellet Insert Bedienungsanleitung

Harman

Harman Accentra52i-TC Bedienungsanleitung

Harman

Harman 300i Bedienungsanleitung

Harman

Harman TL 2.6 Bedienungsanleitung

Harman

Harman Accentra52i-TC Bedienungsanleitung

Harman

Harman P35I Bedienungsanleitung

Harman

Harman Accentra Pellet Insert Montageanleitung

Harman

Harman Magnafire Series Coal StovesMark I Bedienungsanleitung

Harman

Harman Accentra Pellet Insert Montageanleitung

Harman

Harman Accentra 52i Bedienungsanleitung

Beliebte Kamin im Innenbereich Handbücher anderer Marken

Brigantia

Brigantia 35-DVRS31N-2 Betriebsanleitung

Nordpeis

Nordpeis Bergen Bedienungsanleitung

Superior

Superior BCT2536TMN Bedienungsanleitung

Quadra-Fire

Quadra-Fire 5100I-GD-B Bedienungsanleitung

Renaissance

Renaissance RUMFORD 1000 Bedienungsanleitung

Lacunza

Lacunza IV-800 Bedienungsanleitung

Baxi

Baxi 940 Gebrauchsanweisung

Dru

Dru Maestro 60/2 Tall RCH Bedienungsanleitung

Diamond Fireglass

Diamond Fireglass SS-O22 Bedienungsanleitung

HearthStone

HearthStone Windsor Bay 8830 Programmierhandbuch

Napoleon

Napoleon ASCENT B42 Bedienungsanleitung

Enviro

Enviro E33GI Bedienungsanleitung

Smeg

Smeg L30 FABE Montageanleitung

KEDDY

KEDDY K700 Bedienungsanleitung

Godin

Godin 3451 Bedienungsanleitung

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Bedienungsanleitung

Desa

Desa CCFPDFT Bedienungsanleitung

Miles Industries

Miles Industries Vogue 1300IRN Handbuch