Harman P35I Bedienungsanleitung

13-90-774256_R4 • 03/21

P35i Zero Clearance Cabinet Instructions

Part #1-00-774257

Assembly Instructions:

Contents of Kit;

(1) Top Panel

(1) Bottom Panel

(2) Side Panels

(1) Rear Panel

(1) Flue Pipe Insulation Wrap

(2) Wire Wraps

(48) #8 X 1/2” Tek Screws (Self-Tapping)

Dimensions

7-5/16”

(186mm)

Ø 3-7/8”

98mm

16-15/16”

(430mm)

24-3/4”

(629mm)

5-1/4”

(133mm)

28-1/16”

(714mm)

Ø 6-1/16”

156mm

26-1/2”

(673mm)

8-1/4”

(210mm)

7-7/8”

(200mm)

24-3/4”

(629mm)

1”

(25mm)

Tools Needed;

Cordless Drill or Screw gun

1/4” Driver Bit

Small pair of “C clamp” locking

pliers are helpful.

23-90-774256_R4 • 03/21

• Begin with the bottom panel lying at on the oor or

workbench. Place it with the writing facing upward.

Figure 1.

Use care when installing tek screws, do not strip the

holes.

CAUTION

• Stand the other side panel up to the left side of the

bottom, with the electrical box knockout at the bottom

rear corner, and secure it the same way.

• The top panel can now be placed onto the sides, with the

bend going out over the outside of the side panels. Align

the holes and secure with tek screws. Figure 3.

Figure 1 - View of the bottom panel

• Stand a side panel up to the right side of the bottom,

with the (un-used) electrical box knockout in the top rear

location. Notice the bend at the rear of the cabinet will

make the corner and at the front it will be bent outward to

makethefacingange.Lineuptheholesandsecurethe

side panel to the bottom with screws. Figure 2.

Figure 2 - View of the side panel

• Stand the rear panel up to the rear of the cabinet, be

sure the arrow is pointing upward. Secure the rear panel

to the outside of the cabinet. Figure 4.

Figure 4 - View of the rear panel

Figure 3 - View of the top panel

Bend on top goes outside

the side panels.

ZC Box Assembly

33-90-774256_R4 • 03/21

Electrical Installation (If Needed)

A knockout is provided in the left rear corner of the zero

clearance cabinet to install an electrical outlet (not supplied)

if desired. Be sure to ground the receptacle to the zero

clearance cabinet if installed. Figure 8.

Flue Rough-In Support Kit

Flue rough-in support #1-00-774283 installs in the zero

clearancecabinetandprovidesauestubmountingsurface

which will be in the exact position of the stub when it is on

the insert mounting frame. Figure 9.

If you have not yet purchased the insert, order stub kit #

1-00-674040. This kit includes a 4” pipe stub, gasket and

mountingbolts.Ifyoudohavetheinsert,removetheue

stub from the mounting frame. Install the exhaust stub onto

the support using the bolts and nuts from the support kit.

Install with bolts passing upward, through the support plate

andtheangenutsonthetop.Ifinstallingtheoutsideairkit,

install the stub from the kit onto the left side of the support.

It is not necessary to install the gaskets on the support

plate, however you will need them for nal attachment.

Next, using 8 tek screws, install the rough in support into

the cabinet. You can now run your venting and air intake

and permanently attach them to their respective stubs. Be

sure to properly secure both, the venting and the outside air

pipe, so that they cannot move when you remove the rough-

in support. When all of the construction is completed, and

you are ready to install the insert, remove the support plate,

leaving the stubs in place. Install the insert mounting frame

and bolt the stub(s) and gasket(s) to the frame.

IMPORTANT! Install the stub gasket between the stub

and the mounting frame.

Figure 9

Figure 8

Electrical Knockouts

43-90-774256_R4 • 03/21

Framing

• Theangearoundthefrontofthecabinetmustmateuptothenishedface.Usetheholesintheangetosecurethe

cabinet. Alternately, extra mounting holes can be drilled through the cabinet where desired. Figure 5.

Framing and other combustible

materials are permitted to touch the

outside walls of the cabinet.

Top View

ThisFlangeMUSTbeFlushwith

Finished Facing.

Follow vent manufacturers

guidelines and maintain proper

clearance to combustibles.

Figure 5

• Whendeterminingthedepthinyourframingdimensions,thethicknessofthenishmaterialandanybackersmustbe

taken into consideration. Figure 6.

• Todeterminetheproperoorprotection,thehearthmustextendaminimum;15-1/4”(US)or27-1/4”/692mm(CAN)

fromthenishedwallface.

NOTE: Combustible materials may contact any exterior surface of the cabinet.

Side View

Consider the wall nish material

thickness when planning the depth

of your framing. The image at right

shows adequate space for 1/2”

drywall.

1/2” space (Example)

ThisFlangeMUSTbe

Flush with Finished Facing.

Figure 6

Framing leveling

bolts will fit here

Insert Mounting Frames securing holes

Mounting Frame Securing Points - Once framing

is complete secure the mounting frame into the ZC

box using 2” sheet metal screws proper installation.

Figure 5.

53-90-774256_R4 • 03/21

Raised Hearth Installation

Whenconstructingwitharaisedhearth,besuretobuildinsupportforthecabinet.Thisoormaterialcanbeusedunderthe

cabinet only, or it can be applied onto the hearth as well. The image at right shows 3/4” plywood extending onto the hearth.

Notice the support members at the front and rear of the cabinet.

Thehearthnishmaterialcannotexceed1/4”abovethetopedgeofthecabinetbase.Seedetailbelow.Alsoremember,the

hearthneedstoextendtoprovidethepropercombustibleoorprotection.Figure7.

3/4” plywood decking

Support

Members

1/2” Finish Material

(Example)

Mantel must be a minimum of

12 inches above the cabinet top.

It is recommended to install 3/4”

plywood under the entire cabinet,

as a minimum for support.

Hearth nish material should be ush

with, or no more than 1/4” higher than the

top edge of the cabinet base. Exceeding

this height will prevent proper installation.

Ceramic Tile

(Example Only)

Figure 7

Framing leveling

bolts will fit here

Insert Mounting Frames securing holes

Mounting Frame Securing Points - Once framing

is complete secure the mounting frame into the ZC

box using 2” sheet metal screws proper installation.

Figure 5.

63-90-774256_R4 • 03/21

Venting

Follow vent manufacturers guidelines and maintain proper clearance to combustibles.

You must use a minimum 12” vertical section

ofventpipeattachedtotheuestub.

Vent pipe within cabinet must be wrapped with the

included insulation to prevent overheating of motors and

components. Secure the insulation with the wire wraps.

Must use an approved wall pass-through or thimble where

venting penetrates an external wall.

Start the insulation with this point in the rear

oftheuestub.Theinsulationwillwraptwo

times around the pipe. Secure it in place

with the two pieces of wire supplied.

Andere Handbücher für P35I

Dieses Handbuch passt für folgende Modelle

Andere Harman Pelletofen Handbücher

Harman

Harman XXV Freestanding Pellet Stove Bedienungsanleitung

Harman

Harman Absolute43 Bedienungsanleitung

Harman

Harman Advance Pellet Stove Montageanleitung

Harman

Harman P43 Montageanleitung

Harman

Harman XXV Montageanleitung

Harman

Harman PP38+ Montageanleitung

Harman

Harman Advance Pellet Stove Betriebsanleitung

Harman

Harman P68 Bedienungsanleitung

Harman

Harman Advance Freestanding Pellet Stove Bedienungsanleitung

Harman

Harman XXV Bedienungsanleitung

Harman

Harman P35I Bedienungsanleitung

Harman

Harman P43 Bedienungsanleitung

Harman

Harman P43 Bedienungsanleitung

Harman

Harman Accentra Freestanding Pellet Stove Montageanleitung

Harman

Harman XXV Pellet Stove Montageanleitung

Harman

Harman P68 Bedienungsanleitung

Harman

Harman PELLET P61A Montageanleitung

Harman

Harman XXV Montageanleitung

Harman

Harman The Accentra Pellet Stove Montageanleitung

Harman

Harman P43 Montageanleitung

Harman

Harman PC45 Montageanleitung

Harman

Harman Accentra 52i Pellet Insert Bedienungsanleitung

Harman

Harman XXV Montageanleitung

Harman

Harman P43 Bedienungsanleitung

Beliebte Pelletofen Handbücher anderer Marken

SMG

SMG Comfort Bilt HP50GC Bedienungsanleitung

Quadra-Fire

Quadra-Fire MTVI-E2-MBK Bedienungsanleitung

Quadra-Fire

Quadra-Fire MTV-E2-CSB Bedienungsanleitung

Palazzetti

Palazzetti JP Series Installationsanleitung

Travis Industries

Travis Industries Avalon 900 PS Bedienungsanleitung

Flame

Flame FP-45 Bedienungsanleitung

Astra

Astra P-7 Bedienungsanleitung

Heatilator

Heatilator ECO-ADV-PS35 Bedienungsanleitung

Cadel

Cadel aquos 24 h2O Bedienungsanleitung

vicenza

vicenza V4.5 Bedienungsanleitung

MCZ

MCZ VIVO 90 COMFORT AIR 9 M1 Technisches Handbuch

Quadra-Fire

Quadra-Fire 1000 Gold Betriebsanleitung

Ferroli

Ferroli GEMMA Bedienungsanleitung

pleasant hearth

pleasant hearth PH35PS Series Bedienungsanleitung

Quadra-Fire

Quadra-Fire CB1200M-MBK Bedienungsanleitung

England's Stove Works

England's Stove Works 25-EP Bedienungsanleitung

Avalon

Avalon Astoria Bedienungsanleitung

Spartherm

Spartherm Mellino Kurzanleitung