Hayward Sense and Dispense AQL-CHEM Bedienungsanleitung

AQL-CHEM

AQL-CHEM2(-240)

AQL-CHEM3-120/240

Sense & Dispense

Troubleshooting

Guide

Table of Contents

Important safety

instructions Pg. 1

Check System: ‘pH Low’

Pg. 11-13

Important

Information and Compatibility Pg. 2

Check System: ‘pH High’

Pg. 14-17

Maintenance

Pg. 3

Check System: ‘pH

Timeout –Chk

feedr

’Pg. 18-20

Maintenance

: Probe Cleaning Pg. 4

Check System: ‘pH Calibration Error’

Pg. 21

Calibrating the pH Probe (Pro

Logic) Pg. 5

Check System: ‘ORP

Low –Chk

Chlor

.’ Pg. 22-23

Calibrating the pH Probe (Aqua Rite Pro)

Pg. 6

Check System: ‘ORP High

–Chk

Chlor

.’ / ‘Chlor. Off’ Pg. 24-25

Resetting

the ‘pH/ORP Timeout’ Error Pg. 7

Check System: ‘ORP Timeout

–Chlor

Off’

Pg. 26-27

Check System: ‘CSM

Comm Error’ Pg. 8-9

Flow Charts

Pg. 28-33

Check System: ‘pH Probe

Error’ / ‘ORP

Probe Error’

Pg. 10

Sense & Dispense Diagnostics

Page 1

Warning

High Voltage Electrocution Hazard

Hazardous voltage can shock, burn, cause serious injury

and or death. To reduce the risk of electrocution and or

electric shock hazards:

•Only qualified technicians should remove the panel

•Replace damaged wiring immediately

•Insure panel is properly grounded and bonded

Important Information

Page 2

•Sense and Dispense™ is designed for use with the following Goldline Controls:

ProLogic ™(Version 3.0 or greater)

Aqua Plus ™(Version 3.0 or greater)

AquaRite Pro ™

•In all cases, verify that proper water flow is passing through the flow cell.

•Remember to recalibrate the pH probe anytime it has been cleaned or replaced.

•Always measure the complete water chemistry using a third party test kit(s)

capable of testing salt, free chlorine, pH, alkalinity, stabilizer, calcium hardness,

and phosphates.

Recommended probe maintenance schedule:

Probe maintenance indicators:

1. Slow response to water chemistry changes.

2. Increased need to calibrate pH.

3. Inconsistent readings.

Maintenance

Page 3

1. Probes must be clean and free of oils, mineral deposits, and contamination in

order to function properly.

2. Probe tips must be kept wet at all times, if left out of water or storage solution

the probes will dry out and permanent damage will result.

3. Probes must be removed and kept wet during winterization.

4. Replace acid feed tubing annually.

Residential –at least once every three months.

Commercial –every 30 days.

Important Maintenance Information:

Maintenance –Probe Cleaning

Page 4

Step 1

Unscrew & remove the probes from

the flow cell chamber.

Step 2

Step 3

Clean the probe tip and white reference area

with a soft tooth brush and regular

toothpaste or liquid dish washing detergent.

Step 4

Rinse with fresh water, remove and replace

the Teflon tape, & reinstall the probes.

Finally recalibrate the probe (Page 5 for Pro

Logic or Page 6 for Aqua Rite Pro).

Disconnect the probe connectors

from the flow cell.

Note: During the cleaning process it is crucial to keep the tips of both the ORP and pH probes wet. If the probes dry out

they will be incapable of providing an accurate reading.

Calibrating the pH Probe (Pro Logic)

Press the ‘Menu’ button until ‘Maintenance

Menu’ is displayed.

Step 1

Step 2

Press the right arrow button one time and press

the plus (+) button to enter pH calibration.

Step 3

Use the plus (+) or minus (-) keys to increase or

decrease the pH value.

Step 4

Press the right arrow key to show current reading

and new results. Press the right arrow again.

Press the plus (+) key to save the value.

Step 5

Press the right arrow key twice to complete the

calibration.

Step 6

Always verify that the pH probe is clean prior to running the calibration procedure. Also, when testing the pH reading

independently, it is important to obtain test water from the flow cell chamber (where the probes measure the water).

Page 5

Calibrating the pH Probe (Aqua Rite Pro)

Page 6

Press the ‘Settings’ button shown above. The

‘Settings Menu’ will appear.

Press the right arrow button three times and

press the plus (+) button to enter pH

calibration.

Use the plus (+) or minus (-) keys to increase

or decrease the pH value.

Press the right arrow key to show current

reading and new results. Press the right arrow

again.

Press the plus (+) key to save the value.

Press the right arrow key twice to complete

the calibration.

Step 1

Step 2

Step 3

Step 4

Step 5

Step 6

Always verify that the pH probe is clean prior to running the calibration procedure. Also, when testing the pH reading

independently, it is important to obtain test water from the flow cell chamber (where the probes measure the water).

Resetting the pH/ORP Timeout Error

Page 7

ProLogic Aqua Rite Pro

Press the ‘Menu’ button until the ‘Default Menu’ appears.

Press the right arrow button until the ‘pH/ORP Timeout –

Chk Feedr’ appears.

Press the plus button (+) to clear the error.

Press the ‘Info’ button shown above. The ‘Info

Menu’ will appear.

Press the right arrow button until the ‘pH/ORP

Timeout –Chk Feedr’ appears.

Press the plus button (+) to clear the error.

Step 1

Step 2

Step 3

Step 1

Step 2

Step 3

If not connected, plug in and reboot the system. If

connected or error does not go away, power unit

up and go to step C.

Check System Light On

CSM Comm Error

‘CSM Comm Error’ (Chemistry Sensing Module) will appear with the sensing module is not communicating with

the main circuit board.

With the power off, verify the CSM

cable is plugged in.

Step B

Verify the CSM cable is not cut,

kinked or damaged in any way.

Step A

If the cable is damaged then it will need to be

replaced. If the cable does not have any

damage, go to step B.

Page 8

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Hayward Beleuchtungsausrüstung Handbücher

Hayward

Hayward Paramount MDX-R3 Programmierhandbuch

Hayward

Hayward Pro Logic Bedienungsanleitung

Hayward

Hayward VR1000 Bedienungsanleitung

Hayward

Hayward OmniLogic Bedienungsanleitung

Hayward

Hayward SP1091LX Bedienungsanleitung

Hayward

Hayward OmniHub Bedienungsanleitung

Hayward

Hayward KingRay Bedienungsanleitung

Hayward

Hayward Stainless Steel Niches Bedienungsanleitung

Hayward

Hayward Pro Logic Bedienungsanleitung

Hayward

Hayward Pool pH Bedienungsanleitung

Hayward

Hayward Jiffy Niche Bedienungsanleitung

Hayward

Hayward TriStar VS 900 Omni Bedienungsanleitung

Hayward

Hayward Goldline Controls Sense and Dispense Total Pool Chemistry... Bedienungsanleitung

Hayward

Hayward CL220BR series Bedienungsanleitung

Hayward

Hayward AQL-CHEM4-ACID Bedienungsanleitung

Hayward

Hayward CL100 Bedienungsanleitung

Hayward

Hayward WFBRNDBRS Bedienungsanleitung

Hayward

Hayward AquaRite + Bedienungsanleitung

Hayward

Hayward ProLogic Bedienungsanleitung

Hayward

Hayward 3478 PLDBL3 Bedienungsanleitung

Hayward

Hayward OmniLogic Bedienungsanleitung

Hayward

Hayward Vistapool Handbuch

Hayward

Hayward Salt & Swim Datenblatt

Hayward

Hayward OmniPL HLBPRO4SW Bedienungsanleitung

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken

Brizo

Brizo 8SP-MU-4 Bedienungsanleitung

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Bedienungsanleitung

IKEA

IKEA BJÖRKSPIREA Bedienungsanleitung

Laserworld

Laserworld Evolution Series ES-400RGB Bedienungsanleitung

EuroLite

EuroLite LED B-40 Bedienungsanleitung

Qazqa

Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung

Commercial Electric

Commercial Electric 54568141 Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING 304 Series Bedienungsanleitung

Goobay

Goobay 49867 Bedienungsanleitung

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Bedienungsanleitung

Alkalite

Alkalite Krypton KT-81 Bedienungsanleitung

Clas Ohlson

Clas Ohlson GU10 Bedienungsanleitung

DTS

DTS DELTA 10 F Bedienungsanleitung

ring

ring Solar Steplight Bedienungsanleitung

One Stop Gardens

One Stop Gardens 57696 Montageanleitung

SIREM

SIREM Swimeo A2 Bedienungsanleitung

Silvair

Silvair MESH-CEDRP Bedienungsanleitung

S&P

S&P PCRL80 Bedienungsanleitung