HBM BN100A Bedienungsanleitung

Operating Manual | Bedienungsanleitung

English Deutsch

BN100A

Hottinger Baldwin Messtechnik GmbH

Im Tiefen See 45

D-64239 Darmstadt

Tel. +49 6151 803-0

Fax +49 6151 803-9100

[email protected]

www.hbm.com

Mat.: 7-2002.0083

DVS: A0643-6.1 HBM: public

05.2017

EHottinger Baldwin Messtechnik GmbH.

Subject to modifications.

All product descriptions are for general information only.

They are not to be understood as a guarantee of quality or

durability.

Änderungen vorbehalten.

Alle Angaben beschreiben unsere Produkte in allgemeiner

Form. Sie stellen keine Beschaffenheits- oder Haltbarkeits

garantie dar.

Operating Manual | Bedienungsanleitung

English Deutsch

BN100A

2A0643-6.1 HBM: public BN100A

English

1 Safety instructions 3........................................

2 Introduction 8..............................................

2.1 List of components and accessories supplied 8..................

2.2 General 8...................................................

3 Connection 10...............................................

4 Calibration 13...............................................

4.1 Calibration of a measuring chain 13.............................

5 Specifications 15............................................

Safety instructions

BN100A A0643-6.1 HBM: public 3

1 Safety instructions

Use in accordance with the regulations

The BN100A may be connected - instead of a strain

gauge‐based transducer and for the purpose of calibra

tion - only to measuring devices that work with a carrier

frequency of 225 Hz.

Use for any additional purpose shall be deemed to be not

in accordance with the regulations.

In the interests of safety, the instrument should only be

used as described in the Operating Manual. It is also es

sential to observe the appropriate legal and safety regula

tions for the application concerned during use. The same

applies to the use of accessories.

General dangers of failing to follow the safety in

structions

The BN100A corresponds to the state of the art and is

safe to operate. The instrument can give rise to residual

dangers if it is inappropriately installed and operated by

untrained personnel.

Everyone involved with the installation, commissioning or

maintenance of the instrument must have read and un

derstood the Operating Manual and in particular the tech

nical safety instructions.

Conditions on site

Protect the device from direct contact with water (IP20).

It is safe to operate the unit up to an altitude of 2000 m.

Safety instructions

4A0643-6.1 HBM: public BN100A

Install the BN100A so that it can be disconnected from

the mains at any time without difficulty. Make sure that

the mains plug is accessible.

Maintenance and cleaning

The BN100A module is maintenance‐free. Please note

the following points when cleaning the housing:

- Before cleaning, disconnect the devices from the power

supply.

- Clean the housing with a soft, slightly damp (not wet!)

cloth. You should never use solvent, since this could

damage the labelling on the front panel and the display.

- When cleaning, ensure that no liquid gets into the

device or connections.

Residual dangers

The scope of supply and list of components provided with

the BN100A cover only part of the scope of measurement

technology. In addition, equipment planners, installers

and operators should plan, implement and respond to the

safety engineering considerations of measurement tech

nology in such a way as to minimise residual dangers.

Prevailing regulations must be complied with at all times.

There must be reference to the residual dangers connec

ted with measurement technology.

Any risk of residual dangers when working with the

BN100A is pointed out in this manual by means of the

following symbols:

Safety instructions

BN100A A0643-6.1 HBM: public 5

WARNING

Type of danger

Consequences of non-compliance

Averting the danger

SWarning sign:

draws your attention to the danger

SSignal word:

indicates the severity of the danger (see table below)

SType of danger:

mentions the type or source of the danger

SConsequences:

describes the consequences of non-compliance

SDefense:

indicates how the danger can be avoided/bypassed

Danger class according to ANSI

Warning sign, signal word Significance

WARNING This marking warns of a potentially dangerous

situation in which failure to comply with safety

requirements can result in death or serious physical

injury.

Safety instructions

6A0643-6.1 HBM: public BN100A

CAUTION This marking warns of a potentially dangerous

situation in which failure to comply with safety

requirements can result in slight or moderate physical

injury.

Note This marking draws your attention to a situation in

which failure to comply with safety requirements

could lead to damage to property.

On the module

Meaning: Take details in the operating manual into

account

Meaning: CE mark

The CE mark enables the manufacturer to guarantee that

the product complies with the requirements of the relev

ant EC guidelines (the declaration of conformity is avail

able at http://www.hbm.com/HBMdoc).

Working safely

Error messages should only be acknowledged if the

cause of the error is removed and no further danger ex

ists.

The instrument complies with the safety requirements of

DIN EN 61010, Part 1 (VDE 0411, Part 1); Protection

Class I.

To ensure adequate immunity from interference, use only

Greenline shielded ducting (see HBM offprint ”Greenline

shielding design, EMC‐compliant measuring cable;

G36.35.0).

Safety instructions

BN100A A0643-6.1 HBM: public 7

Conversions and modifications

The BN100A module must not be modified from the

design or safety engineering point of view except with our

express agreement. Any modification shall exclude all

liability on our part for any damage resulting therefrom.

In particular, any repair or soldering work on mother

boards is prohibited. When exchanging any modules,

only original HBM parts must be used. Repairs to the unit

may only be carried out by HBM.

Qualified personnel

This instrument is only to be installed and used by quali

fied personnel strictly in accordance with the specifica

tions and with the safety rules and regulations which fol

low. It is also essential to comply with the appropriate

legal and safety regulations for the application concerned

during use. The same applies to the use of accessories.

Qualified personnel means persons entrusted with the

installation, assembly, commissioning and operation of

the product who possess the appropriate qualifications

for their function.

Maintenance and repair work on an open device with the

power on must only be carried out by trained personnel

who are aware of the dangers involved.

Inhaltsverzeichnis

Sprachen:

Beliebte Wandler Handbücher anderer Marken

Camille Bauer

Camille Bauer SINEAX F534 Bedienungsanleitung

Trane

Trane KIT 16724 Montageanleitung

Lumel

Lumel P18 Bedienungsanleitung

B&C Speakers

B&C Speakers DE75PTN Bedienungsanleitung

MAMAC SYSTEMS

MAMAC SYSTEMS PR-243 Handbuch

Mianyang Weibo Electronic

Mianyang Weibo Electronic WB Series Bedienungsanleitung

ProMinent

ProMinent Dulcometer DMT Bedienungsanleitung

MKS

MKS MicroPirani 925 Series Anleitung zur Verwendung

WIKA

WIKA WU-20 Bedienungsanleitung

Alcatel Vacuum Technology

Alcatel Vacuum Technology BARATRON 622A Bedienungsanleitung

Camille Bauer

Camille Bauer SIRAX CH-5610 Bedienungsanleitung

WIKA

WIKA F2802 Bedienungsanleitung

Veris Industries

Veris Industries PW Series Bedienungsanleitung

Simrad

Simrad ES120-7C - REV D Benutzerhandbuch

Airmar

Airmar M260 Bedienungsanleitung

Spirax Sarco

Spirax Sarco ITV1030 Bedienungsanleitung

halstrup-walcher

halstrup-walcher PU10 Bedienungsanleitung

Balluff

Balluff BTL5-P Bedienungsanleitung