HBM C11 Series Bedienungsanleitung

Mounting Instructions | Montageanleitung |

Notice de montage

English Deutsch Français

C11

Hottinger Brüel & Kjaer GmbH

Im Tiefen See 45

D-64293 Darmstadt

Tel. +49 6151 803-0

Fax +49 6151 803-9100

[email protected]

www.hbm.com

Mat.: 7-0111.0008

DVS: A05449_01_Y00_02 HBM: public

06.2021

EHottinger Baldwin Messtechnik

Subject to modifications.

All product descriptions are for general information only.

They are not to be understood as a guarantee of quality or

durability.

Änderungen vorbehalten.

Alle Angaben beschreiben unsere Produkte in allgemeiner

Form. Sie stellen keine Beschaffenheits- oder Haltbarkeits

garantie dar.

Sous réserve de modifications.

Les caractéristiques indiquées ne décrivent nos produits

que sous une forme générale. Elles n'impliquent aucune

garantie de qualité ou de durabilité.

Mounting Instructions | Montageanleitung |

Notice de montage

English Deutsch Français

C11

2A05449_01_Y00_02 HBM: public C11

English

1 Safety instructions 3........................................

2 Markings used 7............................................

2.1 The markings used in this document 7..........................

3 Scope of supply and equipment variants 8...................

4 General instructions for use 9...............................

5 Structure and mode of operation 10...........................

5.1 Transducer 10................................................

5.2 Strain gage covering agent 10..................................

6 Conditions on site 11........................................

6.1 Ambient temperature 11.......................................

6.2 Moisture and corrosion protection 11............................

6.3 Deposits 12..................................................

7 Mechanical installation 13....................................

7.1 Important precautions during installation 13......................

7.2 General installation guidelines 13...............................

8 Electrical connection 15......................................

8.1 EMC protection 16............................................

9 Ordering numbers 17........................................

10 Specifications 18............................................

11 Dimensions in mm 20........................................

Safety instructions

C11 A05449_01_Y00_02 HBM: public 3

1 Safety instructions

Intended use

Force transducers in the C11 series are designed solely for measuring static

and dynamic compressive forces within the load limits stated in the

specifications. Any other use is not the intended use.

To ensure safe operation, it is essential to comply with the regulations in the

mounting instructions, the safety requirements listed below, and the data

specified in the supplied technical data sheets. It is also essential to observe

the applicable legal and safety regulations for the relevant application.

Force transducers are not intended for use as safety components. Please also

refer to the "Additional safety precautions" section. Proper and safe operation

of force transducers requires proper transportation, correct storage, setup and

mounting, and careful operation.

Load-carrying capacity limits

The information in the technical data sheets must be observed when using the

force transducers. The respective specified maximum loads in particular must

never be exceeded. The following limits set out in the technical data sheets

must not be exceeded:

SForce limits

SBreaking forces

SPermissible dynamic loads

STemperature limits

SElectrical load limits

Please note that when several force transducers are interconnected, the load/

force distribution is not always uniform.

Use as machine elements

Force transducers can be used as machine elements. When used in this man

ner, note that to favor greater sensitivity, force transducers were not designed

with the safety factors usual in mechanical engineering. Please refer to the

"Load-carrying capacities" section and to the specifications on page 18.

Safety instructions

4A05449_01_Y00_02 HBM: public C11

Accident prevention

The prevailing accident prevention regulations must be taken into account,

even though the nominal (rated) force values in the destructive range are well

in excess of the full scale value.

Additional safety precautions

Force transducers cannot (as passive transducers) implement any (safety-

relevant) cutoffs. This requires additional components and constructive

measures, for which the installer and operator of the plant is responsible.

In cases where a breakage or malfunction of the force transducer would cause

injury to persons or damage to equipment, the user must take appropriate

additional safety precautions that meet at least the applicable safety and

accident prevention regulations (e.g. automatic emergency shutdown, overload

protection, catch straps or chains, or other fall protection).

The electronic processor that processes the measurement signal should be

designed so that failure of the measurement signal cannot lead to secondary

failures.

General dangers of failing to follow the safety instructions

Force transducers are state-of-the-art and failsafe. Transducers can give rise

to residual dangers if they are mounted, installed, used and operated

inappropriately or by untrained personnel. Every person involved with setting

up, starting up, operating or repairing a force transducer must have read and

understood the mounting instructions and in particular the technical safety

instructions. The force transducers can be damaged or destroyed by non-

designated use of the force transducer or by non-compliance with the mounting

and operating manual, these safety instructions or other applicable safety

regulations (safety and accident prevention regulations of the Employers'

Liability Insurance Association) when using the force transducers. A force

transducer can break, particularly if it is overloaded. The breakage of a force

transducer can cause damage to property or injury to persons in the vicinity of

the force transducer.

If force transducers are not used as intended, or if the safety instructions or

specifications in the mounting and operating instructions are ignored, it is also

possible that a force transducer may fail or malfunction, with the result that

Safety instructions

C11 A05449_01_Y00_02 HBM: public 5

persons may be injured or property damaged (due to the loads acting on or

being monitored by the force transducer).

The scope of supply and performance of the transducer covers only a small

area of force measurement technology, as measurements with (resistive) strain

gage sensors presuppose the use of electronic signal processing. Equipment

planners, installers and operators should always plan, implement and respond

to the safety engineering considerations of force measurement technology in

such a way as to minimize residual dangers. Pertinent national and local

regulations must be complied with.

Conversions and modifications

The design or safety engineering of the transducer must not be modified with

out our express permission. Any modification shall exclude all liability on our

part for any damage resulting therefrom.

Maintenance

The force transducers of the C11 series are maintenance free. We recommend

to calibrate the force transducer at regular intervals.

Disposal

In accordance with national and local environmental protection and material

recovery and recycling regulations, old transducers that can no longer be used

must be disposed of separately and not with normal household garbage.

If you require more information about disposal, please contact your local

authorities or the dealer from whom you purchased the product.

Qualified personnel

Qualified personnel means persons entrusted with installing, mounting, starting

up and operating the product who possess the appropriate qualifications for

their work.

This includes people who meet at least one of these three requirements:

SKnowledge of the safety concepts of automation technology is a require

ment and as project personnel, you must be familiar with these concepts.

Safety instructions

6A05449_01_Y00_02 HBM: public C11

SAs automation plant operating personnel, you have been instructed how to

handle the machinery. You are familiar with the operation of the equipment

and technologies described in this documentation.

SAs commissioning engineers or service engineers, you have successfully

completed the training to repair the automation systems. Moreover, you are

authorized to start up, ground and label circuits and equipment in

accordance with safety engineering standards.

During use, compliance with the legal and safety requirements for the relevant

application is also essential. The same applies to the use of accessories.

The force transducer may only be installed by qualified personnel, strictly in

accordance with the specifications and with the safety requirements and

regulations.

Markings used

C11 A05449_01_Y00_02 HBM: public 7

2 Markings used

2.1 The markings used in this document

Important instructions for your safety are highlighted. It is essential to follow

these instructions to prevent accidents and damage to property.

Symbol Meaning

WARNING This marking warns of a potentially dangerous situa

tion in which failure to comply with safety require

ments may result in death or serious physical injury.

CAUTION This marking warns of a potentially dangerous

situation in which failure to comply with safety

requirements may result in minor to moderate

physical injury.

Notice This marking draws your attention to a situation in

which failure to comply with safety requirements may

result in damage to property.

Important

This marking draws your attention to important

information about the product or about handling the

product.

Tip

This marking indicates tips for use or other

information that is useful to you.

Information

This marking draws your attention to information

about the product or about handling the product.

Emphasis

See …

Italics are used to emphasize and highlight text and

identify references to chapters, diagrams, or external

documents and files.

Scope of supply and equipment variants

8A05449_01_Y00_02 HBM: public C11

3 Scope of supply and equipment variants

SC11 force transducer

SC11 installation instructions

STest record

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Beliebte Wandler Handbücher anderer Marken

Camille Bauer

Camille Bauer SINEAX F534 Bedienungsanleitung

Trane

Trane KIT 16724 Montageanleitung

Lumel

Lumel P18 Bedienungsanleitung

B&C Speakers

B&C Speakers DE75PTN Bedienungsanleitung

MAMAC SYSTEMS

MAMAC SYSTEMS PR-243 Handbuch

Mianyang Weibo Electronic

Mianyang Weibo Electronic WB Series Bedienungsanleitung

ProMinent

ProMinent Dulcometer DMT Bedienungsanleitung

MKS

MKS MicroPirani 925 Series Anleitung zur Verwendung

WIKA

WIKA WU-20 Bedienungsanleitung

Alcatel Vacuum Technology

Alcatel Vacuum Technology BARATRON 622A Bedienungsanleitung

Camille Bauer

Camille Bauer SIRAX CH-5610 Bedienungsanleitung

WIKA

WIKA F2802 Bedienungsanleitung

Veris Industries

Veris Industries PW Series Bedienungsanleitung

Simrad

Simrad ES120-7C - REV D Benutzerhandbuch

Airmar

Airmar M260 Bedienungsanleitung

Spirax Sarco

Spirax Sarco ITV1030 Bedienungsanleitung

halstrup-walcher

halstrup-walcher PU10 Bedienungsanleitung

Balluff

Balluff BTL5-P Bedienungsanleitung