Heat & Glo ST-HVBI-AUB Bedienungsanleitung

Heat & Glo • ST-HVBI-AUB • 2082-980 Rev. B • 3/11

MODELS:

ST-HVBI-AUB

ST-HVBILP-AUB

SAI Global

Ref No GSCS20165

AS 4553:2008

Owner’s Manual

Installation and Operation

• DO NOT USE OR STORE FLAMMABLE

MATERIALS NEAR THIS APPLIANCE.

• DO NOT SPRAYAEROSOLSINTHEVICIN-

ITY OF THIS APPLIANCE WHILE IT IS IN

OPERATION.

• What to do if you smell gas

- DO NOT try to light any appliance.

- DO NOT touch any electrical switch. DO

NOT use any phone in your building.

- Immediately call your gas supplier from a

neighbor’sphone.Follow thegassupplier’s

instructions.

- If you cannot reach your gas supplier, call

the ﬁre department.

• Installation and service must be performed

by a qualiﬁed installer, service agency, or the

gas supplier.

WARNING: If the information in these

instructions is not followed exactly, a ﬁre

or explosion may result causing property

damage, personal injury, or death.

WARNING

This appliance has been supplied with an integral barrier

to prevent direct contact with the ﬁxed glass panel. DO

NOT operate the appliance with the barrier removed.

Contact your dealer or Hearth & Home Technologies if the

barrier is not present or help is needed to properly install one.

HOT SURFACES!

Glassandothersurfacesarehotduring

operation AND cool down.

Hot glass will cause burns.

• DO NOT touch glass until it is cooled

• NEVER allow children to touch glass

• Keep children away

• CAREFULLY SUPERVISE children in same room as

ﬁreplace.

• Alert children and adults to hazards of high temperatures.

High temperatures may ignite clothing or other ﬂammable

materials.

• DO NOT PLACE ARTICLES ON OR AGAINST THIS

APPLIANCE.

• Keep clothing, furniture, draperies and other ﬂammable

materials away.

This is a room sealed appliance and no other ventilation is

required than what is provided.

DO NOT DISCARD THIS MANUAL

NOTICE

• Leave this manual with

party responsible for use

and operation.

DO NOT

DISCARD

• Important operating

and maintenance

instructions included.

• Read,understandand follow

these instructions for safe

installation and operation.

WARNING! DO NOT modify this appliance.

2Heat & Glo • ST-HVBI-AUB • 2082-980 Rev. B • 3/11

IMPORTANT: Read all instructions carefully before starting installation.

Failure to follow these installation instructions may result in a possible ﬁre

hazard and will void the warranty. Save this manual for future reference.

MODEL ST-HVBI-AUB

SAI GLOBALAPPROVED FOR NATURAL

GAS OR PROPANE AS A BALANCED FLUE

HEATER.

Referto theappliance dataplates forgas consump-

tions and pressures.

Installation of this appliance should only be carried

out by an authorized person in accordance with the

manufacturers instructions. All relevant codes and

regulations laid down by the gas ﬁtting authorities,

municipal building regulations, electrical wiring

regulations, and the requirements of the AGA Gas

Installation Code must be observed.

This appliance and its components are tested and

safewhen installed inaccordance withthis Installa-

tion Manual. Report to your dealer any parts dam-

agedinshipment, speciﬁcallycheckglass condition.

The gas logs and ﬂue system components are in

separate packages. Read all instructions before

starting installation and follow these instructions

PLEASE READ THIS MANUAL BEFORE INSTALLING AND

USING THIS APPLIANCE.

carefully during installation to ensure maximum

beneﬁt and safety. Failure to follow them will void

your warranty and may present a ﬁre hazard.

The Heat & Glo warranty will be voided by, and

Heat & Glo disclaims any responsibility for the fol-

lowing actions:

• Installation of any damaged heater or ﬂue

system component

• Modiﬁcation of the heater or balanced ﬂue

system installation other than as instructed by

Heat & Glo.

• Improper positioning of the gas logs or the

glass door

• Installation and/or use of any component part

not manufactured or approved by Heat & Glo,

not withstanding any independent testing

laboratory or other party approval of such

component part or accessory.

Heat & Glo, a brand of Hearth & Home Technologies, Inc.

7571 215th Street West, Lakeville, MN 55044

Heat & Glo • ST-HVBI-AUB • 2082-980 Rev. B • 3/11

TABLE OF CONTENTS

1.0 INSTALLATION INSTRUCTIONS......................................................................4

1.1 Locating the Heater.....................................................................................5

1.2 Framing the Heater......................................................................................6

1.3 Flue System Approvals and Installations.....................................................9

1.4 Connecting the Gas Supply.........................................................................21

1.5 Ignition System Wiring.................................................................................22

1.6 Blower Wiring ..............................................................................................23

1.7 Mantel Clearances.......................................................................................24

1.8 Log Placement.............................................................................................25

1.9 Installer Testing............................................................................................28

2.0 OPERATING INSTRUCTIONS. .........................................................................28

2.1 Operation Cautions......................................................................................29

2.2 Safety and Lighting Information...................................................................29

2.3 Control Module Operation ...........................................................................31

2.4 Remote Control Operation...........................................................................32

3.0 SERVICING AND MAINTENANCE. ..................................................................38

3.1 Removal of Covers for Servicing.................................................................39

3.2 Removal of Components for Service...........................................................39

3.3 Parts Replacement......................................................................................39

3.4 Adjustments and Replacement Parts..........................................................39

3.5 Maintenance Tasks......................................................................................40

3.6 Troubleshooting...........................................................................................41

4.0 REPLACEMENT PARTS...................................................................................42

Limited Lifetime Warranty...................................................................................45

4Heat & Glo • ST-HVBI-AUB • 2082-980 Rev. B • 3/11

Figure 1. Diagram of the ST-HVBI-AU

1.0 INSTALLATION INSTRUCTIONS

When planning a heater installation, it’s necessary to

determine:

• Where the unit is to be installed.

• The ﬂue system conﬁguration to be used.

• Gas supply piping.

• Electrical wiring.

• Framing and ﬁnishing details.

• Whether optional accessories—devices such as

wall switch, or remote control—are desired.

If the heater is to be installed on carpeting or tile, or on

anycombustible materialother thanwood ﬂooring,the

heater should be installed on a metal or wood panel

that extends the full width and depth of the heater.

32-1/2 in.

(816mm)

36-3/16 in.

(919.3mm)

2-1/4 in.

(58mm)

4-3/4 in.

(121mm)

4-1/2”

(114mm)

4-1/16”

(102mm)

34-3/4 in.

(882mm) 4-1/2”

(114mm)

2-9/16”

(64mm)

24 in.

(610m)

9-11/16”

(245mm)

17-15/16”

(456mm)

42”

(1067mm)

ELECTRICAL

ACCESS

GAS LINE

ACCESS

Ø8”

(202mm)

12”

(306mm) 46-5/8”

(1184mm)

Ø7-7/8”

(202mm)

12”

(306mm)

5-1/4”

(132mm) ½”

(13mm)

FLUE COLLAR

TOP STANDOFFS

FLUE

COLLAR

TOP

LOUVER

ACCESS

DOOR

GAS CONTROLS

& LABELS

GAS LINE

ACCESS ELECTRICAL

ACCESS

Heat & Glo • ST-HVBI-AUB • 2082-980 Rev. B • 3/11

1.1 Locating the Heater

The diagram below shows space and clearance re-

quirements for locating a heater within a room.

Minimum Clearances

from the Heater to Combustible Materials

Figure 2. Heater Dimensions and Locations

Forminimumclearances,see thedirectﬂuetermination

clearance diagrams on pages 6 and 7 in this manual.

Minimum Clearances

from the Flue Pipe to Combustible Materials

* The clearance to the ceiling is measured from

the top of the unit, excluding the standoffs (see

Figures 1 and 2).

Thedistance fromthe unit tocombustible construction

is to be measured from the unit outer wrap surface to

the combustible construction, NOT from the screw

heads that secure the unit together.

mm inches

Glass Sides or Ends..........914 ...................36

Floor ....................................0 ......................0

Rear Flue............................13 ................... 1/2

Metal Sides or Ends ...........13 ................... 1/2

Top......................................64 ..................2-1/2

Ceiling*..............................787 ...................31

mm Inches

Vertical Sections..............25.................1

Horizontal Sections

Top.....................................75.................3

Bottom...............................25.................1

Sides..................................25.................1

At Wall Firestops

Top.....................................64..............2-1/2

Bottom...............................13............... 1/2

Sides..................................25.................1

Clearance Requirements

The top, back, and sides of the heater are deﬁned by

stand-offs.Theminimumclearance to aperpendicular

wall extending past the face of the heater is 25 mm

(1 in.). The metal ends of the heater may NOT be

recessed into combustible construction.

914 mm

GLASS

914 mm

6Heat & Glo • ST-HVBI-AUB • 2082-980 Rev. B • 3/11

A B C D * E *

42-5/8 in. 42-1/2 in. 23 in. 35 in. 53-3/4 in.

(1.21 m) (1.08 m) (584 mm) (889 mm) (1.37 m)

Figure 3. Framing Dimensions

* Note: These dimensions show the center of

the horizontal ﬂue pipe. The center of the

framing hole is one inch (25.4 mm) above

the center of the ﬂue pipe. Framing should

be constructed of 51 mm x 102 mm (2 in. x

4 in.) lumber or heavier.

1.2. Framing the Heater

Framing can be built before or after the heater is set

in place. Framing should be positioned to accommo-

date wall coverings and heater facing material. The

diagram below shows framing reference dimensions.

CAUTION: MEASURE HEATER DIMENSIONS AND

VERIFY FRAMING METHODS AND WALL COVER-

ING DETAILS, BEFORE FRAMING CONSTRUC-

TION BEGINS.

WARNING: FRAMING DIMENSIONS AS-

SUME USE OF 1/2 INCH (12.7 MM) (THICK

WALL COVERING MATERIALS ON EXTE-

RIOROFFRAMINGONLYANDNOSHEET-

ROCK ON INTERIOR OF FRAMING.

Heat & Glo • ST-HVBI-AUB • 2082-980 Rev. B • 3/11

NOTES: 1. All distances are measured vertically or horizontally along the wall to a point

in line with the nearest part of the terminal.

2. Prohibited area below electricity meter or fuse box extends to ground level.

3. See clause 5.13.6.6 for restrictions on a ﬂue terminal under a roofed area.

4. See Appendix J, Figure J1(a) and J2(a) for clearances required from a ﬂue

terminal to a LP Gas cylinder. A ﬂue terminal is considered to be a source of ignition.

MINIMUM CLEARANCES REQUIRED FOR BALANCED FLUE TERMINALS

OR THE FLUE TERMINALS OF OUTDOOR APPLIANCES

Figure 4

a - Below eaves, balconies or other projections: MIN. CLEARANCE (mm)

Appliances up to 50 MJ/h input..............................................................................................300

Appliances over 50 MJ/h input...............................................................................................500

b - From the ground or above a balcony.........................................................................................300

c - From a return wall or external corner.........................................................................................500

d - From a gas meter (M)..............................................................................................................1000

e - From an electricity meter or fuse box (P)...................................................................................500

f - From a drain or soil pipe............................................................................................................150

g - Horizontally from any building structure (unless appliance approved

for closer installation) or obstruction facing a terminal...............................................................500

h - From any other ﬂue terminal, cowl, or combustion air intake ....................................................500

j - Horizontally from an openable window, door, non-mechanical air inlet, or any other opening into a

building, with the exception ofsub-ﬂoor ventilation:

Appliances up to 150 MJ/h input............................................................................................500

Appliances over 150 MJ/h input...........................................................................................1500

k - From a mechanical air inlet, including a spa blower...............................................................1500

n - Vertically below an openable window, non-mechanical air

inlet or any other opening into a building, with the exception of............................See table below

T= Flue terminal M= Gas meter Shading indicates prohibited

I= Mechanical air inlet P= Electricity meter or fuse box areas for ﬂue terminals

openable

window

door

kdb

See note 2

See note 3

CLEARANCE 'n' (mm)

Space Heaters All other appliances

Up to 50 MJ/h input Up to 50 MJ/h input Over 50 MJ/h input and

Up to 150 MJ/h input Over 150 MJ/h input

150 500 1000 1500

8Heat & Glo • ST-HVBI-AUB • 2082-980 Rev. B • 3/11

NOTE: PIPES OVERLAP 32 mm (1-1/4 in.) AT EACH JOINT.

Figure 5. DVP-Series Direct Flue Component Speciﬁcations (127 mm (5 in.) inner pipe / 203 mm (8 in.) outer pipe)

DVP90ST

320 mm

286 mm

185 mm

32 mm

18 mm

218 mm

DVP36

DVP48

1219 mm

610 mm

914 mm

102 mm

152 mm

DVP4

DVP6

305 mm

DVP12

51 mm MIN.

DVP12A

310 mm MAX.

DVP24

251 mm 45

261 mm

DVP45

362 mm

Heat & Glo • ST-HVBI-AUB • 2082-980 Rev. B • 3/11

Figure 6. Flue System Components and Termination Kits

1.3 Flue System Approvals and Installation

A. Flue System Approvals

These models are approved to use DVP series direct

ﬂue pipe components and terminations (see Figures 5

and6).Approvedﬂue systemcomponents arelabeled

for identiﬁcation. This pipe is tested and listed as an

approved component of the heater. The pipe is tested

to be run inside an enclosed wall. There is no require-

ment for inspection openings at each joint within the

wall.Thereis no requiredpitch forhorizontal ﬂue runs.

NO OTHERFLUEING SYSTEMSOR COMPONENTS

MAY BE USED.

Detailedinstallation instructionsareincluded witheach

ﬂue termination kit and should be used in conjunction

with this Installers Guide.

Theﬂameandemberappearancemayvarybasedonthe

type of fuel burned and the ﬂueing conﬁguration used.

Identifying Flue Components

The ﬂue systems installed on this gas heater may

include one, two, or three 90° elbow assemblies. The

relationships of vertical rise to horizontal run in ﬂue

conﬁgurations using 90° elbows MUST BE strictly

adhered to. The rise to run relationships are shown in

theﬂueing drawings andtables. Referto the diagrams

on the next several pages.

This model has a 45° elbow built into it. It may be posi-

tionedtoﬂueeither horizontalorvertical. Dependingon

theinstallation,decide whichdirectiontheelbow should

befacing. Remove the8 screws fromthe corner cover

plate. Position the 45º elbow as desired and replace

the corner cover plate with the 8 screws.

HORIZONTAL TERMINATION

WALL FIRESTOPS

90º ELBOW

VERTICAL

TERMINATION

STORM COLLAR

ROOF FLASHING

PIPE LENGTH

CEILING FIRESTOP

TERMINATION KITS

DVP-TRAP2 DVP-TVHW

10 Heat & Glo • ST-HVBI-AUB • 2082-980 Rev. B • 3/11

Figure 7

STRAIGHT OUT

HORIZONTAL FLUEING

Max. Run

610 mm (24 in.)

Figure 8

TERMINATION CAP

STRAIGHT UP

VERTICAL FLUEING

V (FT.)

12.2 M MAX. (40 ft.)

Andere Handbücher für ST-HVBI-AUB

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Heat & Glo Kamin im Innenbereich Handbücher

Heat & Glo

Heat & Glo MEZZO-1000-AU Bedienungsanleitung

Heat & Glo

Heat & Glo SL-36-Ultimate Bedienungsanleitung

Heat & Glo

Heat & Glo SL-550TRS-E Bedienungsanleitung

Heat & Glo

Heat & Glo NORTHSTAR-BK Bedienungsanleitung

Heat & Glo

Heat & Glo Wood Burning Fireplace HST-42D Bedienungsanleitung

Heat & Glo

Heat & Glo FOUNDATION FDN-4-PIER Bedienungsanleitung

Heat & Glo

Heat & Glo SOHO24B Bedienungsanleitung

Heat & Glo

Heat & Glo 6000GBV-IPI Bedienungsanleitung

Heat & Glo

Heat & Glo Soho-N-AU Montageanleitung

Heat & Glo

Heat & Glo Pier-HVB-IPI Bedienungsanleitung

Heat & Glo

Heat & Glo TRUE-36G-IFT Bedienungsanleitung

Heat & Glo

Heat & Glo COSMO32-IFT-B Bedienungsanleitung

Heat & Glo

Heat & Glo FOUNDATION Series Bedienungsanleitung

Heat & Glo

Heat & Glo SL-550TV-D Bedienungsanleitung

Heat & Glo

Heat & Glo TRUE-36S-IFT Bedienungsanleitung

Heat & Glo

Heat & Glo Bravo Bedienungsanleitung

Heat & Glo

Heat & Glo EXCLAIM-50 Bedienungsanleitung

Heat & Glo

Heat & Glo 6000GBV Bedienungsanleitung

Heat & Glo

Heat & Glo GRL-700-AU Bedienungsanleitung

Heat & Glo

Heat & Glo SL-350TRSI-AUE Bedienungsanleitung

Heat & Glo

Heat & Glo TRUE-36G-IFT Bedienungsanleitung

Heat & Glo

Heat & Glo SL-550F-LP Bedienungsanleitung

Heat & Glo

Heat & Glo EXCLAIM-36 Bedienungsanleitung

Heat & Glo

Heat & Glo Rutherford-42 Bedienungsanleitung

Beliebte Kamin im Innenbereich Handbücher anderer Marken

Brigantia

Brigantia 35-DVRS31N-2 Betriebsanleitung

Nordpeis

Nordpeis Bergen Bedienungsanleitung

Superior

Superior BCT2536TMN Bedienungsanleitung

Quadra-Fire

Quadra-Fire 5100I-GD-B Bedienungsanleitung

Renaissance

Renaissance RUMFORD 1000 Bedienungsanleitung

Lacunza

Lacunza IV-800 Bedienungsanleitung

Baxi

Baxi 940 Gebrauchsanweisung

Dru

Dru Maestro 60/2 Tall RCH Bedienungsanleitung

Diamond Fireglass

Diamond Fireglass SS-O22 Bedienungsanleitung

HearthStone

HearthStone Windsor Bay 8830 Programmierhandbuch

Napoleon

Napoleon ASCENT B42 Bedienungsanleitung

Enviro

Enviro E33GI Bedienungsanleitung

Smeg

Smeg L30 FABE Montageanleitung

KEDDY

KEDDY K700 Bedienungsanleitung

Godin

Godin 3451 Bedienungsanleitung

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Bedienungsanleitung

Desa

Desa CCFPDFT Bedienungsanleitung

Miles Industries

Miles Industries Vogue 1300IRN Handbuch