Heat Controller VMH 09 Bedienungsanleitung

Heat Controller, Inc. • 1900 Wellworth Ave. • Jackson, MI 49203 • (517)787-2100 • www.heatcontroller.com

INSTALLATION

MANUAL

VMH 09/12/18/27/36

Version C

InverterFlex

Ductless Mini-Split Heat Pump

VMH InverterFlex Mini-Split INSTALLATION MANUAL Heat Controller, Inc.

Table of Contents

Safety Precautions

Warnings and Cautions ...........................................................................2

Installation Instructions

Selecting an installation location..............................................................3

Accessories..............................................................................................4

System installation...................................................................................5

Indoor unit installation..............................................................................6

Outdoor unit installation ...........................................................................9

Refrigerant Pipe Connection

Refrigerant pipe connection...................................................................10

Electrical Work

Electrical Work .......................................................................................12

Air Purging

Air purging with vacuum pump...............................................................14

Safety and refrigerant leak check ..........................................................16

Testing the System

Test Run.................................................................................................17

Caution

• Contact an authorized service technician for repair or maintenance of this unit.

• Contact an authorized installer for installation of this unit.

• Installation work must be performed in accordance with local and national electrical

codes and standards by authorized personnel only.

Heat Controller, Inc. INSTALLATION MANUAL VMH InverterFlex Mini-Split

WARNING!

CAUTION!

This symbol indicates the possibility of death or serious injury.

This symbol indicates the possibility of injury or damage to property.

This symbol denotes item that is PROHIBITED from doing.

The items to be followed are classied by the symbols:

1) Do not install without an authorized servicer/installer.

2) Install according to this installation instruction. If installation is defective, it can cause water leakage, or

electrical shock/re.

3) Use the supplied accessories and specied parts for installation.

4) Install the indoor unit on a wall strong enough to hold the unit’s weight. Install the outdoor unit on a

raised concrete pad or blocks to provide a solid, level foundation. In a location with high winds, anchor

the unit and provide an air bafe. In snowy areas (for heat pump models), install the outdoor unit on a

raised platform so that it is higher than drifting snow. Provide snow vents.

5) For electrical work, follow local and national electric codes and these installation instructions. An

independent circuit and single outlet must be used. If electrical circuit capacity is not enough or defects

are found in electrical work, it will cause electrical shock or re.

6) Use the specied cable and connect tightly and clamp the cable so that no external force will stress the

terminal. Loose wiring may cause overheating at the connection points and a possible re hazard.

7) Wiring routing must be properly arranged so that control board cover is xed properly. If control board

cover is not xed perfectly, it will cause overheating at connection point of terminal, re or electrical shock.

8) When charging the unit, take care not to let air/substances other than the specied refrigerant go into

refrigeration cycle. Otherwise, it will cause lower capacity, abnormal high pressure in the refrigeration

cycle, explosion and injury.

9) Do not modify the length of the power supply cord or use an extension cord, and do not share the

single outlet with other electrical appliances. Otherwise, it will cause re or electrical shock.

1) This equipment must be grounded and installed with a ground leakage current breaker. It may cause

electrical shock if grounding work doesn’t comply with local/national electric codes.

2) Do not install the unit at place where leakage of ammable gas may occur. If gas leaks and

accumulates near the unit, it may cause re.

3) Carry out drainage piping as mentioned in installation instructions. If not done correctly, water may

enter the room and damage personal belongings.

WARNING!

CAUTION!

• Read the follow SAFETY PRECAUTIONS carefully before installation.

• Electrical work must be performed by a licensed electrician. Be sure to use the correct rating of the power

cord and main circuit for the model to be installed.

• Incorrect installation due to ignoring the instruction will cause harm or damage.

n The seriousness is classied by the following indications.

VMH InverterFlex Mini-Split INSTALLATION MANUAL Heat Controller, Inc.

1. Wall-mounted type

Selecting installation place

Read completely, then follow step by step.

Indoor unit

• Do not expose the indoor unit to heat or steam.

• Select a place where there are no obstacles in front or

around the unit.

• Make sure that condensation drainage can be conveniently

routed away.

• Do not install near a doorway.

• Ensure that the space on the left and right of the unit is more than 5in.(12cm).

• Use a stud nder to locate studs to prevent unnecessary damage to the wall.

• The indoor unit should be installed on the wall at a height of 6.5ft.(2m) or more from the oor.

• The indoor unit should be installed allowing a minimum clearance of 6in.(15cm) from the ceiling.

• Any variations in pipe length may require adjustment to refrigerant charge.

• Do not expose unit to direct sunlight. The sun will fade the plastic cabinet and affect its appearance.

Outdoor unit

• If an awning is built over the outdoor unit to prevent

direct sunlight or rain exposure, make sure that heat

radiation from the condenser is not restricted.

• Ensure that the clearance around the back of the unit

is more than 12in.(30cm) and left side is more than

12in.(30cm). The front of the unit should have more

than 79in.(200cm) of clearance and the connection

side (right side) should have more than 24in.(60cm)of

clearance.

• Do not place animals and plants in the path of the air

inlet or outlet.

• Take the air conditioner weight into account and select a place where noise and vibration will not be an issue.

• Select a place so that the warm air and noise from the air conditioner do not disturb neighbors.

Rooftop installation

• If the outdoor unit is installed on a roof structure, be sure to level the unit.

• Ensure the roof structure and anchoring method are adequate for the unit location.

• Consult local codes regarding rooftop mounting.

• If the outdoor unit is installed on roof structures or external walls, this may result in excessive noise and vibra-

tion, and may also be considered a non-serviceable installation.

Heat Controller, Inc. INSTALLATION MANUAL VMH InverterFlex Mini-Split

Accessories

INSTALLATION INSTRUCTIONS

Note: Except the above parts provided, the other parts needed during installation you must

purchase.

Parts you must

purchase

(The minimum pipe

wall-thickness

of 0.7mm is required. )

6.35

9.53

12.7

Self-tapping Screw B ST2.9X10

Remote controller

Installation Plate

Name of Accessories

Self-tapping Screw A ST3.9X25

Seal (See Page 8 for details)

Drain Joint

Connecting

pipe

Assembly

Liquid side

Plastic Expansion Sheath

Number Q ty/one unit

Gas side

9Remote controller holder 1

( 12000Btu/h model)

(See page 8 for details)

Level gauge

Screwdriver

Electric drill,Hole core drill ( 26in.(65mm))

Flaring tool set

Specified torque wrenches: 1.8kgf.m, 4.2kgf.m,

5.5kgf.m, 6.6kgf.m(different depending on model No.)

Spanner (half union)

Hexagonal wrench (1.5in.(4mm))

Gas-leak detector

Tools needed for installation:

Vacuum pump

Gauge manifold

Users manual

Thermometer

Multimeter

Pipe cutter

Measuring tape

Qty/unit

Level gauge

Screwdriver

Electric drill, Hole core drill (o .25in.(65mm))

Flaring tool set

Torque wrench

Spanner (half union)

Hexagonal wrench (1.5in.(4mm))

Gas-leak detector

1/4" (6.35mm)

3/8" (9.53mm) (<12,000 Btu/h model)

1/2" (12.7mm) (≥12,000 Btu/h model)

VMH InverterFlex Mini-Split INSTALLATION MANUAL Heat Controller, Inc.

• Use a stud nder to locate studs to prevent

unnecessary damage to the wall.

• A minimum pipe run of 9.8 ft (3m) is re-

quired to minimize vibration & excessive

noise.

• Two of the “A,” “B” and “C” air ow direc-

tions should be free from obstructions for

the outdoor unit.

CAUTION

Single-Dual Zone

Single-Tri Zone

Single-Quad Zone

Heat Controller, Inc. INSTALLATION MANUAL VMH InverterFlex Mini-Split

Indoor unit installation (wall-mounted type)

1. Installation Plate

A. Mount the installation plate horizontally on struc-

tural parts (studs) of the wall with proper clear-

ance around the installation plate.

B. If the wall is made of brick, concrete or the like,

drill eight (8) 5mm (0.2in.) diameter holes in

the wall.Insert anchor for appropriate mounting

screws.

C. Fit the installation plate on the wall with eight (8)

type “A” screws.

NOTE:

Fit the Installation Plate and drill holes in the wall ac-

cording to the wall structure and corresponding mount-

ing points on the installation plate. The Installation

Plate may be slightly different according to the different

models of indoor unit.

2. Drill a hole in the wall

A. Determine hole positions according to the dia-

gram detailed in Fig.5. Drill one (1) hole ( 3in.

(65mm)) slanting slightly toward the outdoors,

as shown in Fig. 6.

B. Always use wall hole conduit when drilling metal

grid, metal plate or the like.

3. Connective Pipe and Drainage Installation

A. Run the drain hose sloping downward. Do not

install the drain hose as illustrated in Fig.7.

Model A in. (mm) B in. (mm)

<12,000 Btu/h

28 (710) 10 (250)

30 (750) 10 (250)

31 (780) 11 (270)

≥12,000 Btu/h

32 (790) 10 (265)

31 (780) 11 (270)

32 (815) 11 (280)

VMH InverterFlex Mini-Split INSTALLATION MANUAL Heat Controller, Inc.

INSTALLATION INSTRUCTIONS

1. For the left-hand and right-hand piping,

remove the pipe cover from the side

panel.

2. For the rear-right-hand and rear-left-hand

piping, install the piping as shown in Fig.9.

Bend the connective pipe to be laid at 4in.(43mm)

height or less from the wall.

3. Fix the end of the connective pipe. (Refer

to Tightening Connection in REFRIGERANT

PIPING CONNECTION)

Connective pipe installation

2. When connecting extension drain hose,

insulate the connecting part of extension

drain hose with a shield pipe, do not let

the drain hose slack.

Right-hand piping

Left-hand piping

Rear-right piping

Rear-left piping

Indoor unit outline

Connective pipe

Fig.8

Fig.9

Fig.10

4. Piping and wrapping

Bundle the tubing, connecting cable, and drain

hose with tape securely, evenly as shown in

Fig.11.

Because the condensed water from rear of the

indoor unit is gathered in ponding box and is

piped out of room. Do not put anything else in

the box.

Indoor unit

Connective

pipe

Pipe room

Ponding box

Wrapping belt

Connective

cable

Drain hose

Fig.11

Connect the indoor unit first, then the

outdoor unit.

Do not allow the piping to let out from

the back of the indoor unit.

Be careful not to let the drain hose slack.

Heat insulated both of the auxiliary piping.

Be sure that the drain hose is located at

the lowest side of the bundle. Locating

at the upper side can cause drain pan

to overflow inside the unit.

Never intercross nor intertwist the power

wire with any other wiring.

Run the drain hose sloped downward to

drain out the condensed water smoothly.

CAUTION

• Connect the indoor unit rst, then the outdoor

unit.

• Do not allow the piping to let out from the back

of the indoor unit.

• Be careful not to let the drain hose slack.

• Heat insulate both of the auxiliary piping.

• Be sure that the drain hose is located at the low-

est side of the bundle. Locating at the upper side

can cause drain pan to overow inside the unit.

• Never intercross nor intertwine the power wire

with any other wiring.

• Run the drain hose sloped downward to drain

out the condensed water smoothly.

Wall Cap

Heat Controller, Inc. INSTALLATION MANUAL VMH InverterFlex Mini-Split

1. Pass the piping through the hole in the wall.

2. Put the upper claw at the back of the indoor

unit on the upper hook of the installation

plate, move the indoor unit from side to

side to see that it is securely fastened (see

Fig.12).

3. Separate the bottom of the indoor unit from

the wall by inserting spacer, etc., between

the indoor unit and the wall. Remove spacer

after piping is complete.

4. Push the lower part of the indoor unit up on

the wall, then move the indoor unit from side

to side, up and down to check if it is secure.

4. Indoor unit installation

Spacer

VMH InverterFlex Mini-Split INSTALLATION MANUAL Heat Controller, Inc.

Outdoor Unit Installation

Outdoor installation precaution

• Install the outdoor unit on a rigid base to prevent

increasing noise level and vibration.

• Determine the air outlet direction where the

discharged air is not blocked. If the installation

place is exposed to strong winds, ensure the unit

is lengthwise along the wall or provide a suitable

air bafe.

• If suspending the unit, follow the bracket manu-

facturer’s instructions.

• Use a raised concrete pad or concrete blocks to

provide a solid, level surface. Securely anchor the

unit down with bolts.

• Be sure there are no obstacles which block radiat-

ing air.

• In a snowy area, install the outdoor unit on a raised

platform that is higher than drifting snow.

Anchoring outdoor unit

Anchor the outdoor unit with 5/16" (8mm) or 3/8"

(10mm) bolt and nut tightly and horizontally on a

concrete or rigid mount.

Outdoor unit dimensions

WxHxD in. (mm)

Mounting Dimensions

A in. (mm) B in. (mm)

29.9 x 23.2 x 11.2 (760 x 590 x 285) 20.9 (530) 11.4 (290)

33.3 x 27.4 x 13.2 (845 x 695 x 335) 22 (560) 13.2 (335)

35.2 x 33.9 x 13.0 (895 x 860 x 330) 23.2 (590) 13.1 (333)

39.0 x 38.0 x 14.0 (990 x 965 x 355) 24.5 (623) 14.4 (366)

Fig. 45

Andere Handbücher für VMH 09

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Heat Controller Wärmepumpe Handbücher

Heat Controller

Heat Controller HKV Betriebsanleitung

Heat Controller

Heat Controller TPR Series Leitfaden

Heat Controller

Heat Controller HRE1318/1360-1A Bedienungsanleitung

Heat Controller

Heat Controller HP Series Gebrauchsanweisung

Heat Controller

Heat Controller RPHE-093G Series Bedienungsanleitung

Heat Controller

Heat Controller SMH 24 Bedienungsanleitung

Heat Controller

Heat Controller B-DVH09SD-0 Bedienungsanleitung

Heat Controller

Heat Controller HBH/V Compact Gebrauchsanweisung

Heat Controller

Heat Controller SMA Series Bedienungsanleitung

Heat Controller

Heat Controller HEV Series Leitfaden

Heat Controller

Heat Controller VMH30SB-1 Bedienungsanleitung

Heat Controller

Heat Controller TPRG Series Bedienungsanleitung

Heat Controller

Heat Controller H 006 Bedienungsanleitung

Heat Controller

Heat Controller SMA 09 Bedienungsanleitung

Heat Controller

Heat Controller AS-W093E7Y0 Bedienungsanleitung

Heat Controller

Heat Controller VMH 09 Handbuch

Heat Controller

Heat Controller VMH C Series Bedienungsanleitung

Heat Controller

Heat Controller DMH18DB-1 Bedienungsanleitung

Heat Controller

Heat Controller TGC Series Bedienungsanleitung

Heat Controller

Heat Controller VMH09SC-1 Bedienungsanleitung

Heat Controller

Heat Controller Geothermal Bedienungsanleitung

Heat Controller

Heat Controller HEV Series Gebrauchsanweisung

Heat Controller

Heat Controller VMH 36 Series Gebrauchsanweisung

Heat Controller

Heat Controller VMH 09 Bedienungsanleitung

Beliebte Wärmepumpe Handbücher anderer Marken

MICROWELL

MICROWELL HP 1000 GREEN Bedienungsanleitung

Sanyo

Sanyo SAP120FCH Bedienungsanleitung

Daikin

Daikin EHYHBH05AA Bedienungsanleitung

Panasonic

Panasonic WH-SDF03E3E5 Leitfaden

Bryant

Bryant 544B Bedienungsanleitung

Airxcel

Airxcel 45000 Series Handbuch

Mitsubishi Electric

Mitsubishi Electric PUZ-SWM60VAA Bedienungsanleitung

Dimplex

Dimplex LI 16I-TUR Benutzerhandbuch

Carrier

Carrier WSHP Open v3 Kurzanleitung zur Einrichtung

TGM

TGM CTV14CN018A Bedienungsanleitung

Carrier

Carrier 38MGQ Series Bedienungsanleitung

Kokido

Kokido K2O K880BX/EU Fehlerbehebungshandbuch

Viessmann

Viessmann VITOCAL 300-G PRO Type BW 2150 Kurzanleitung

Carrier

Carrier 48EZN Bedienungsanleitung

Viessmann

Viessmann KWT Vitocal 350-G Pro Series Betriebsanleitung

Ariston

Ariston NIMBUS Bedienungsanleitung

Weishaupt

Weishaupt WWP L 7 Benutzerhandbuch

GE Zoneline AZ85H09EAC Bedienungsanleitung