Heath Zenith 5610 Bedienungsanleitung
© 2015 HeathCo LLC
Motion Sensor
Entryway Light
Models 5610/15
The Heath®/Zenith Motion Sensor Entryway Light turns
on up to 60 watts of incandescent light when motion
is detected and then, after a selectable time period,
automatically turns the light off. The built-in photocell
keeps the light off during daylight hours.
Sensor
Entryway Light
Mounting Nut and Stem
2 Wire
Connectors
2 Screws
Mounting Strap and
Grounding Wire
globe
(5615) or jar
(5610)
Requirements
• The Entryway Light requires 120-volts AC.
• If you want to use Manual Override, the light must be
wired through a switch.
•Some codes require installation by a qualified
electrician.
This package includes:
OPERATION
* resets to Auto Mode at dawn.
Note: When first turned on wait about 1 1/2minutes for
the circuitry to calibrate.
MANUAL MODE
ON-TIME
10 5 1 TEST
10 5 1 TEST
ON-TIME
TEST
... back on.
AUTO
1 Second
OFF then...
Put the ON-TIME switch in the
1, 5, or 10 minute position.
Put the ON-TIME switch on the bottom
of the sensor in the TEST position.
Manual mode only works at night
because daylight returns the sensor
to AUTO.
Flip the light switch off for one second
thenbackontotogglebetween AUTO
and MANUAL MODE.
Manual mode works only with the
ON-TIME switch in the 1, 5, or 10
position.
Move ON-TIME Switch to
1, 5, or 10 minutes
Mode Switching Summary
Flip light switch off
for one second then
back on*
MANUAL MODE
AUTO
TEST
* If you get confused while switching modes, turn the
power off for one minute, then back on. After the cali-
bration time the control will be in the AUTO mode.
Mode: On-Time Works: Day Night
Test 5 Seconds x x
Auto 1, 5, or 10 Minutes x
Manual Until Dawn* x
2
ON-TIME
TEST 1 5 10
SENS
MIN MAX
TEST AND ADJUSTMENT
1. Turn on the circuit breaker and light switch.
In the test position shown above, the light will turn
on for 5 seconds each time motion is detected dur-
ing both daylight and darkness.
ON-TIME SENS
Bottom of Sensor
NOTE: Sensor has a 1 1/2minute calibration period
before it will detect motion. When first turned
on, wait 1 1/2minutes.
INSTALLATION
For best performance, mount the fixture about 7 feet
(2.1 m) above the ground.
1. Turn the power to the lighting circuit off at the
fuse or circuit breaker box.
2. Remove the existing light fixture.
3. Install the mounting strap
into the junction box. Ori-
entation of the strap may
be different.
4. Strip about 5/8 in. (15 mm)
insulation off of the existing
junction box wiring.
5. Connectthe white (neutral) junction boxwiretothe
white Entryway Light wire.Twist the wires together
and secure with a wire connector.
6. Connect the green or
bare (ground) mounting
strapwireto a grounded
wire or to a grounded
metal box.
7. Connect the black
(hot) junction box
wiretotheblackEn-
tryway Light wire.
8. Install the mounting stem into the strap so
that it extends out about 3/4 in. (19 mm).
9. Install the fixture over
the mounting stem.
10. Install and tighten the
mounting stem nut.
Holding Screw
for Globe or Jar
11. Caulk the back edge of the light and mounting
surface with silicone weather sealant.
12. Install a 60 Watt maximum light bulb into the lamp
holder. Do not overtighten. Higher wattages will
void warranty.
13. Loosen the front holding screw so the globe or jar
cover can be installed. Secure by tightening the
screw. Do not overtighten.
2. For aiming, turn the SENSITIVITY (SENS) control
to the mid position and the ON-TIME control to the
TEST position.
3
Avoid aiming the control at:
• Objects that changetemperaturerapidly, suchas heat-
ing vents or air conditioners. These heat sources
could cause false triggering.
• Areas where pets or traffic may trigger the control.
•Nearby large, light-colored objects reflecting light
may trigger the shut-off feature. Do not point other
lights at the sensor.
110°
30 ft (9.1m)
The detector is less sensitive to motion directly towards
it and more sensitive to across motion.
7 ft.
(2.1 m)
Maximum Range Maximum
Coverage Angle
3. Rotate the sensor base left
and right to aim the sensor.
Adjust the sensor eye up
and down to obtain desired
coverage range.
4. Walk through the coverage
area noting where you are
whenthe lights turn on.Move
the sensor head up, down,
or sideways to change the
coverage area.
5. SetSENSITIVITYas needed.
Too much sensitivity may
increase false triggering.
6.
Set the amount of TIME the
lightsstayonaftermotionisde-
tected (1, 5, or 10 minutes).
SPECIFICATIONS
Range . . . . . . . . . . . . . . Up to 30 ft (9.1 m) [varies with
surrounding temperature].
Sensing Angle . . . . . . . . Up to 110°
Electrical Load. . . . . . . . Up to 60 Watt Maximum In-
candescent
Up to 15 Watt Maximum
CFL
Power Requirements . . . 120 VAC, 60 Hz
Operating Modes. . . . . . TEST, AUTO and MANUAL
OVERRIDE
Time Delay . . . . . . . . . . 1, 5, 10 minutes
Sensitivity . . . . . . . . . . . Adjustable
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1)
this device may not cause harmful interference, and (2)
thisdevicemustacceptanyinterferencereceived,includ-
ing interference that may cause undesired operation.
CAN ICES-3 (B)/NMB-3(B)
Least Sensitive Most Sensitive
Sensor
Motion
Motion
Aim Sensor
Down for Short
Coverage
Aim Sensor
Higher for Long
Coverage
IMPORTANT: Whenusing aCFLbulb,itisrecommend-
ed to use the maximum ON-TIME setting. Frequent
ON/OFF cycling of the bulb will reduce its life.
WARNING: Do not use SBCFL bulb marked
“Not for use in totally enclosed fixtures”.
SYMPTOM
Light will not come
on.
Light comes on
in daylight.
POSSIBLE CAUSE
1. Light switch is turned off.
2. Light bulb is loose or burned
out.
3. Fuse is blown or circuit breaker
is turned off.
4. Daylight turnoff is in effect (re-
check after dark).
5. Incorrect circuit wiring, if this is a
new installation.
6. Re-aim the sensor to cover de-
sired area.
1. Entryway Light may be installed
in a relatively dark location.
2. Entryway Light is in Test. (Set
control switch to an ON-TIME
position).
SYMPTOM
Lightcomeson
fornoapparent
reason.
Light stays on
continuously.
Light flashes
on and off.
POSSIBLE CAUSE
1. Entryway Light may be sensing small
animals or automobile traffic (re-aim
sensor).
2. Sensitivity is set too high. (Reduce
sensitivity).
1. Entryway Light is pointed toward a
heat source like an air vent, dryer
vent,orbrightly-painted heat-reflective
surface. (Reposition sensor).
2. Lightcontrol isinManualMode.(Switch
to Auto.)
1. Heatbeing reflectedfrom otherobjects
may be affecting the sensor. (Reposi-
tion sensor).
2. Entryway Light is in the Test mode and
warming up. (Flashing is normal under
these conditions).
TROUBLESHOOTING GUIDE
Learn more about home shop we have.
Dieses Handbuch passt für folgende Modelle
1
Andere Heath Zenith Zubehör Handbücher
Heath Zenith
Heath Zenith 121AC Bedienungsanleitung
Heath Zenith
Heath Zenith Wireless Push Button Accessory 598-1151-02 Bedienungsanleitung
Heath Zenith
Heath Zenith notifi alert Bedienungsanleitung
Heath Zenith
Heath Zenith Notif Bedienungsanleitung
Heath Zenith
Heath Zenith Decorative Wireless Chime 598-1000-07 Bedienungsanleitung
Heath Zenith
Heath Zenith DualBrite 5716 Bedienungsanleitung
Heath Zenith
Heath Zenith SL-7464-03 Bedienungsanleitung
Heath Zenith
Heath Zenith 5838 Bedienungsanleitung
Heath Zenith
Heath Zenith DUAL BRITE SL-5597 Bedienungsanleitung
Heath Zenith
Heath Zenith Wireless Strobe Chime 6144 Bedienungsanleitung
Heath Zenith
Heath Zenith Secure Home 5215 Bedienungsanleitung
Heath Zenith
Heath Zenith 598-1109-06 Bedienungsanleitung
Heath Zenith
Heath Zenith Replacement Motion Sensor SH-5407 Bedienungsanleitung
Heath Zenith
Heath Zenith Wireless Push Button Accessory 598-1105-05 Bedienungsanleitung
Heath Zenith
Heath Zenith InTune MP3 Door Chime Bedienungsanleitung
Heath Zenith
Heath Zenith 7797 Bedienungsanleitung
Heath Zenith
Heath Zenith 598-1112-04 Bedienungsanleitung
Heath Zenith
Heath Zenith SL-6155 Series Bedienungsanleitung
Heath Zenith
Heath Zenith SL-6153 Bedienungsanleitung
Heath Zenith
Heath Zenith Hardwired Electronic Chime 598-1313-00 Bedienungsanleitung
