Heath Zenith 7309 Bedienungsanleitung
C
H
I
M
E
V
O
L
U
M
E
TUNE–HOLD
1 SECOND.
SYNC–HOLD
3 SECONDS.
RESET–HOLD
10 SECONDS.
Wireless Chime
© 2018 HeathCo LLC
1. Remove orange battery tab from push button.
Remove back of case by pushing in tab on bottom
with a small screwdriver (see Figure 1). Remove
orange battery tab.
2. Install 3 alkaline “C” batteries. Press in latch on
rear of chime and lift off battery cover (see Figure 2).
Install 3 alkaline “C” batteries (not included) into
chime. Make sure batteries are installed according
to the diagram inside the chime (see Figure 3).
Replace battery access door onto back of chime.
3. Test range. Temporarily position chime and push
button where you want them mounted. Press push
button to verify chime and push button work prop-
erly. If chime does not sound, see Troubleshooting.
4. Adjust volume control to desired volume (see
Figure 2).
Figure 1
Figure 2
Figure 3
WARNING:To prevent possible SERIOUS
INJURY or DEATH:
• NEVER allow small children near batteries.
• If battery is swallowed, immediately notify
doctor.
This chime requires 3“C” alkaline batteries (not included). In typical use, alkaline
batteries will last up to one year.
This package includes (Style of push button and chime may vary from illustration):
Model
Wireless
chime Wireless push
button Hardware
pack
7309 ✔ ✔ ✔
7312 ✔✔(x2) ✔
Chime Volume Control
C
H
I
M
E
V
O
L
U
M
E
TUNE– HOLD
1 SECOND.
SYNC– HOLD
3 SECONDS.
RESET–HOLD
10 SECONDS.
2
C
H
I
M
E
V
O
L
U
M
E
TUNE–HOLD
1SECOND.
SYNC–HOLD
3SECONDS.
RESET–HOLD
10SECONDS.
5. Mount push button. Use either screws or double
sided tape to mount push button.
•
Screw Mounting: To mount with screws, remove
back of case by pushing in tab on bottom with a
small screwdriver (see Figure 1). Note: Remove
material in screw holes (if needed) before mounting
with screws. Attach back of case to door jamb or
wall (see Figure 4). Snap front of push button on.
• Tape Mounting: When attaching push button
using double sided tape, make sure the surface
of the door jamb or wall is clean.
6. Mount chime. Determine mounting location.
• Use template on back cover of manual for screw
placement. Mark two hole locations 3-1/8" (8 cm)
apart. Note: Make sure holes are level before
drilling.
• Drill two 7/32" (5.5 mm) diameter pilot holes for
wall anchors and insert anchors.
• Mount keyhole screws to wall leaving about 1/8"
(3 mm) of the screw threads exposed.
•
Using keyholes on back of chime base, hang base
on screws (see Figure 5).
Figure 5
Figure 4
Keyhole Slots
Keyhole Screw (x2)
3
Tune Settings
The chime has different selectable tunes:Ding (one note tune), Ding-Dong (two note
tune), Westminster, or Whittington.The factory setting is for the Westminster tune.
This tune can be changed by following the instructions in the Tune Setting Table.
Note: All chime models are designed to work with up to 5 push buttons (sold
separately). All chimes are designed to play only two different tunes no matter how
many push buttons are used.
C
H
I
M
E
V
O
L
U
M
E
TUNE – HOLD
1 SECOND.
SYNC – HOLD
3 SECONDS.
RESET – HOLD
10 SECONDS.
Tune Setting Table
Inside Push Button
Back of Chime
Jumper Off Jumper On
Push Button Chime Tune
Jumper - ON
(Back Door)
——— Ding
Jumper - OFF
(Front Door)
Press and release button on chime.
Listen for selected tune. Repeat to
select different tune.
Selected Musical
Tune
Tune Selection Guide
Front Door
Ding-Dong
Westminster
Whittington
Back Door
Ding
ON
1 2
CR2032
TYPE “C”
TYPE “C”
1 2 3 4 5 6 7 8
CR2032
ON
1 2
TYPE “C”
TYPE “C”
1 2 3 4 5 6 7 8
4
Troubleshooting
1. PROBLEM: Chime does not sound.
A. POSSIBLE CAUSE: Push button and chime are not synced.
A. CORRECTIVE ACTION: Sync the push button and chime.
• Press and hold the button on the chime until the chime sounds a “Beep-
Beep”.
• Press the push button within 30 seconds. The chime will sound a “Beep-
Beep” tone to indicate the push button is synced.
• Press the push button to ensure operation.
B. POSSIBLE CAUSE: Batteries not installed correctly.
B. CORRECTIVE ACTION: Make sure batteries are installed according to the
diagram inside the push button and chime.
C. POSSIBLE CAUSE: Batteries are dead.
C. CORRECTIVE ACTION: Check charge of push button and chime batteries
and replace if necessary.
2. PROBLEM: Batteries seem okay, but the chime does not work after installation.
A. POSSIBLE CAUSE: Chime or push button is mounted on metal or near metal
studs. Note: Metal reduces transmission range.
A. CORRECTIVE ACTION: Use 1/4 in. to 1/2 in. (6 to 13 mm) wood shims to
move chime or push button away from metal surface.
B. POSSIBLE CAUSE: Chime is mounted near concrete floor or wall. Note:
Concrete may reduce range.
B. CORRECTIVE ACTION: Move chime away from concrete surface.
C. POSSIBLE CAUSE: Chime and push button are installed too far apart.
C. CORRECTIVE ACTION: Locate chime closer to push button.
5
3. PROBLEM: Chime sounds when not intended (false triggers).
POSSIBLE CAUSE: Chime is receiving interference from another wireless
device.
CORRECTIVE ACTION: Reset chime and push button.
• Remove push button battery. Wait 30 seconds.
• Press and hold the push button for 10 to 15 seconds within 60 seconds
after installing battery into the push button.
• Press and hold the button on the chime until the chime sounds a “Beep-
Beep-Beep-Beep”.
• To re-sync the push button and chime, press and hold the button on the
chime until the chime sounds a “Beep-Beep”.
• Press the push button within 30 seconds. The chime will sound a “Beep-
Beep” tone to indicate the push button is synced.
• Press the push button to ensure operation.
Note: The push button and chime come synced from the factory. The range of the
wireless chime can vary with location, temperature, and battery condition.
C
H
I
M
E
V
O
L
U
M
E
TUNE – HOLD
1 SECOND.
SYNC – HOLD
3 SECONDS.
RESET – HOLD
10 SECONDS.
C
H
I
M
E
V
O
L
U
M
E
TUNE – HOLD
1 SECOND.
SYNC – HOLD
3 SECONDS.
RESET – HOLD
10 SECONDS.
Learn more about home shop we have.
Dieses Handbuch passt für folgende Modelle
2
Inhaltsverzeichnis
Andere Heath Zenith Zubehör Handbücher
Heath Zenith
Heath Zenith 6168 Bedienungsanleitung
Heath Zenith
Heath Zenith 5867 Service-Handbuch
Heath Zenith
Heath Zenith Hardwired Electronic Chime 598-1113-05 Bedienungsanleitung
Heath Zenith
Heath Zenith Replacement Motion Sensor SH-5407 Bedienungsanleitung
Heath Zenith
Heath Zenith 598-1109-06 Bedienungsanleitung
Heath Zenith
Heath Zenith Wireless Mechanical Battery Operated Chime... Bedienungsanleitung
Heath Zenith
Heath Zenith Notifi Elite Bedienungsanleitung
Heath Zenith
Heath Zenith 6180 Series Bedienungsanleitung
Heath Zenith
Heath Zenith Notifi elite Bedienungsanleitung
Heath Zenith
Heath Zenith Wireless Push Button Accessory 598-1105-06 Bedienungsanleitung
Heath Zenith
Heath Zenith HZ-1802-BK-A Bedienungsanleitung
Heath Zenith
Heath Zenith Wireless Push Button Accessory 598-1105-05 Bedienungsanleitung
Heath Zenith
Heath Zenith DUAL BRITE SL-5597 Bedienungsanleitung
Heath Zenith
Heath Zenith Secure Home 5215 Bedienungsanleitung
Heath Zenith
Heath Zenith Wireless Chime 6153/62/71/72 Bedienungsanleitung
Heath Zenith
Heath Zenith Wireless Christmas Chime 598-1127-03 Bedienungsanleitung
Heath Zenith
Heath Zenith 7311 Bedienungsanleitung
Heath Zenith
Heath Zenith 5316 Bedienungsanleitung
Heath Zenith
Heath Zenith Single Entrance Chime 23/M Bedienungsanleitung
Heath Zenith
Heath Zenith Hardwired Electronic Chime 598-1313-00 Bedienungsanleitung
