Hexagon TESA Compact Series Bedienungsanleitung
INSTRUCTIONS
MODE D’EMPLOI
BEDIENUNGSANLEITUNG
MANUALE D’USO
INSTRUCCIONES DE USO
E
S
D
F
I
DIALTRONIC COMPACT
3
Installing and replacing the battery
(or Power cable)
Mise en place et remplacement de la
batterie (ou câble Power)
Einbau und Austausch der Batterie
(oder Power Kabel)
Installazione e sostituzione della batteria
(o del cavo Power)
Colocación y sustitución de la batería
(o cable Power)
Battery / batterie / Batterie / batteria / batería: lithium 3V, type CR2032
E
4
E
5
Description
1. Button
2. Clamping Ø8 or 3/8”
3. Lifting cap (depends on version)
4. Measuring insert Ø3/ M2.5 or 4-48-UNF
5. Slot for battery or Power Cable
6. Dovetail xing
7. Measurement units (mm/ INCH)
8. +/ - Indicator
9. Low battery
10. Keypad lock
11. 6-digit display
12. Send data
Key function
Short press <1s
Prolonged press
Release
E
6
1 . Operating features of the instrument
PRESET - Main function: Preset recall (default value 0.000)
DATA - Data transmission
Main function of the preset recall can be attributed to the sending of data by using the FUNC menu (see chap. 3).
- Preset value
Preset value other than 0.000 can be set using RS232.
- Personalising the functions
It is possible to activate or de-activate certain functions of the instrument via RS232 (see chap. 6).
- Data transmission parameters
4800 Baud connection, 7 bits, even parity, 2 stop bits.
2. Start
Press button to start.
E
mm IN
mmmm
mm
mm
mm
mm
mmmm
mmmm
7
3. Instrument functions
Long press on button gives access to the menus.
Preset (default function) or Data
Data or Preset
Main function selection (Preset/Data)
E
mm IN
mmmm
mm
mm
mm
mm
mmmm
mmmm
8
4. Switching o
The dial gauge goes automatically into stand-by if not used for 10 minutes. the value of the origin is retained by the sensor,
and the instrument automatically restarts with any movement of the measurement probe, button action or RS232 command.
The instrument can be switched o completely for a long period of non-use, but this will necessitate a zero reset on restart
(the origin will be lost): prolonged press (>6 s) on button until OFF is displayed.
Units selection (mm or Inch) &
measurement direction (positive or
negative sense)
Switching o
E
9
5. Re-initialising the instrument
All settings (unit and measuring direction) will remain after a battery change. The initial instrument settings can be restored
at any time by a prolonged press (>12 s) on button until the message is displayed.
6. Personalising the instrument
Access to the functions of your instrument can be personalised, for more information see manufacturer’s website (requires
you to connect your instrument via a Power RS / USB cable).
It is possible to activate or deactivate the required functions
7. Connecting the instrument
The instrument can be connected to a peripheral via a power (RS or USB) cable. See page 3 for connecting the Power
cable.
Measured values can be transmitted and the instrument driven using predened retro-commands (see chap. 8 for a list of
the main commands).
E
10
8. List of the main commands
Selection and conguration Interrogation
CHA+ / CHA Change measurement direction ? Current value?
FCTxxx Assign «favorite» function CHA? Measurement direction?
MM / IN Change measurement unit BAT? Battery status?
KEY0 / KEY1 Lock / unlock keypad (BAT1 = OK, BAT0 = low battery)
PRE [+/-]xxx.xxx Modify preset value KEY? Keypad locked?
LCAL dd.mm.yy Modify last calibration date FCT? Main function active?
NCAL dd.mm.yy Modify next calibration date UNI? Measurement unit active?
OUT / OUT1 Activate / de-activate contin. data transmission PRE? Preset value?
SET Zero reset LCAL? Date of last calibration?
UNI1 / UNI0 Activate / de-activate change of units NCAL? Date of next calibration?
RES2 / RES3 Change of résolution SET? Main instrument parameters?
OFF Switch-o (wake up using a button or RS) ID? Instrument identication code?
RST Re-initialisation of the instrument RES? Resolution value?
SBY Put instrument in Stand by SN? Instrument serial code?
VER? Version No. and date of rmware?
Dieses Handbuch passt für folgende Modelle
4
Inhaltsverzeichnis
Sprachen:
Andere Hexagon Messgerät Handbücher
Hexagon
Hexagon Aptiv ESR 2.5 Bedienungsanleitung
Hexagon
Hexagon TP-R-400 Bedienungsanleitung
Hexagon
Hexagon TESA RUGOSURF 10G Bedienungsanleitung
Hexagon
Hexagon TESA INOTEST Bedienungsanleitung
Hexagon
Hexagon Leica Nova TS60 Bedienungsanleitung
Hexagon
Hexagon TESA FMS Series Bedienungsanleitung
Hexagon
Hexagon TESA IMICRO Bedienungsanleitung
Hexagon
Hexagon GeoMax ZEL400HV Bedienungsanleitung
Hexagon
Hexagon TESA ALESOMETRE Bedienungsanleitung
Hexagon
Hexagon DIGICO 200 Bedienungsanleitung
