HIMO C26 Bedienungsanleitung

E-Bike

Please read the instruction manual carefully before using your bike

Do not use the bike until you know its performance. Please keep the

instruction manual properly

Notes for using

According to the regulations on the implementation of the road traffic safety law of the People's Republic

of China, e-bike rider must be at least 16 years old.

When driving in the non-motorized lane, the maximum speed shall not exceed 15km/h;On roads

without non-motorized lanes, drive on the right side of the roadway.

Don't cause injury by lending your bike to someone who can't handle it.

Passengers or goods shall be carried according to laws and regulations.

Riding in rain and snow, the braking distance will be extended, pay attention to slow down;Avoid

traveling in bad weather such as heavy rain.

Before riding, check the braking system and clean the reflector to avoid blocking.

Obey traffic rules strictly

Safe of using the product

Please strictly abide by the traffic laws and regulations, prepare helmets, protective

equipment and other protective equipment before riding, and pay attention to driving

safety

Do not ride with one hand or two hands away from the handle.

Do not park in building doors, evacuation staircases, walkways, and safety exits.

Do not charge inside residential building and park, should be far from combustible when

charging, please charge according to regulation time, charging time should not be too long.

Correct use and maintenance of batteries, old batteries can not be disassembled without

authorization, should be organized by the professional departments recycling. Know how

to use charger and warning terms, use original charger.

When adjusting the saddle position, be careful not to expose the safety mark line of the

saddle tube.

Preparation before riding

Whether the power circuit and lighting are good.

Whether the front and rear brake lever are

good.

Whether the handlebars and front and

rear wheels are in a tight state.Whether the

tire pressure is normal.

Bike coding position

（The code at the bottom of frame）

Main technical parameters of the bike

Controller Spec.

Under voltage protection

Over current protection

Under the condition of full power, the endurance is 75kg, the temperature is about 25℃, the environment of

flat road is still without wind, and the driving condition is measured at 15km/h uniform speed under the

energy-saving mode. The actual endurance will be different due to factors such as load, temperature, wind

speed, road surface and operating habits.

Front and rear wheel center distance

Max weight

Maximum design speed

Assisting rang

Electric range

Consumes electricity（100KM）

Loading weight

Dimensions (L*W*H)

Battery Spec.

Lithium ion batteryBattery type

Capacity

Voltage

Motor Spec.

Brushless dc motor

Motor type

Rated power

Rated speed

Voltage

Brake sensor

Overspeed alarm

Electrical schematic

Motor

Controller

Booster sensor

Power signal

The cathode

Head light signal

Head light

Knob

Battery

Charger port

5Acharging fuse

30A fuse

Display

Handle signal

The cathode

The signal of handle

The wire for lock of power

Power

Brake signal

Head light signal

Blank

The cathode

Overspeed warning signal

Get to know C26 quickly

(Wiggle the wheels to increase the bottom space for easier battery

installation and removal)

Battery mounting and locking

Battery out

Insert the key to open the battery lock,hold the battery with your hand and push

the safety clasp to remove the battery.(please be sure to hold the battery with

your hand when taking out the battery to avoid the accident of touching the ground)

1.Insert the key to rotate to the open state,put the battery into the

predetermined position of the body,push it upward until the machine

makes a clear sound and the battery is energized.

2.Push the battery safety buckle to the tight position.

3.Turn key to lock and pull out.(the key cannot be pulled out when the battery lock is open).

Security card buckle

Battery lock

Display and riding mode

Display introduction

Speed

Mileage accumulated

(switching)

Subtotal mileage

(switching) Headlight indication

Mode button

Switch button

Power indicator

Gear position indication

(power/medium speed/high speed)

The first default gear is "ECO" assisted cycling mode;

Pedal riding speed reaches 5KM/H;

Electric assist riding

Electric riding

Normal riding

Parking mode

Pedal riding

In the startup state;

Long press 3 seconds to switch

mode to "P",

Open parking mode.

Press the button to switch to the medium speed gear

of"MID" electric cycling mode;This mode can be started

by twisting the crank or the speed exceeds 5km/h.

Press the button to switch to the high-speed gear of

"HIGH" electric cycling mode;This mode can be

started by twisting the crank or the speed exceeds

5km/h.

Long press the button for 3 seconds to start the

electric bike;

Long press the key for 3 seconds to

close the electric bike;

Switch for the headlight

Mileage pattern

Long press button for 3 second to open the headlight

Long press button for 3 second to close the headlight

In the startup state;

Long press the key for 3 seconds to

close the electric bike;

Press button to switched between (TRIP) →

accumulated mileage (ODO)

Battery charging

First plug the power supply pin of the charger into the

charging port ofthe battery, and then plug the power

supply pin into the power supply.

Under charging state, the indicator light of charger is

red,and when fully charged, it is green.

Unplug the power plug after charging.

If the battery is charged in the bike, please turn off

the instrument power.

Daily charge

Soft cap

Charging port

Charger

Indicator light

Power supply pin

Prepare 1 suitable phillips screwdriver, 2 no. 7 batteries.

Remove the rear lamp, unscrew the front panel screw, open the rear housing,

and replace the battery.

Buckle the rear shell, screw well, install it on the fixing plate, and

replace the battery.

Taillight is designed as an independent switch.

Press the switch when using.

Tail light

Rear reflector

Switch

Cross screwdriver

No.7 battery

2 pcs

Battery capacity button

Power indicato

When your battery is in the state of charging or not

charging, press the power display button to display

the current remaining power.

Check battery capacity

Taillight opening and maintenance Change battery

Transmission using

Transmission diagram

When using a speed change system, try not to skip gears, which can easily damage the transmission.It is not possible to change two gears at a time above,

should be a level of adjustment, can better protect the transmission system.

Do not reverse the transmission system when the bike stops running, or when it is going downhill. This will not only be bad for the transmission system, but also may

cause accidents.

If it is their transmission fault, or gear is not accurate situation, will affect the performance of the transmission, at this time should be timely to the professional

bike shop maintenance, in case of aggravation of the fault.

When using the transmission system, also pay attention to the following details

Gear Speed

Slow

Fast

Moderate

Power

Rlax

Moderate

Hard