Hioki 3665-20 Bedienungsanleitung

Network Construction with One Single Instrument

Must-have item for building a 10 GB networks

Wiremap

Cable Length

Direction

Supports shielded cables

Get NVP-Enhanced Measurement Accuracy

Identify Up to 21 Cable Destinations

Detect Split Pairs with Wiring Check

CAT6A

LAN CABLE HiTESTER 3665

Detect the existence of

shields or check for shield integrity.

UnshieldedShielded

Fully Compatible to

CAT6A

LAN Cables

For wiring confirmation and locating broken wires after installation.

Quick PASS/FAIL reading helps you complete your work faster.

Super-

sensitive

Detection

Can you nd split pairs?

Split PairProper Wiring

１１

２２

３３

４４

５５

６６

７７

８８

１１

２２

３３

４４

５５

６６

７７

８８

１１

２２

３３

４４

５５

６６

７７

８８

１

２

３

４

５

６

７

８

LAN cable wires should be connected as shown in the

diagram above, such that Pins 3 and 6 are twisted.

A "Split Pair" is detected when Pins 3 and 6 are not

twisted and paired together as shown above.

FAIL

PASS

Direction (ID No.)

Identify the terminator ID here.

Obtain a record of the entire

length of the cable, or up to the

point where the cable is damaged.

Large PASS/FAIL display, cable type, reason for cable failure and shield condition.

Wiremap (Wiring Status)

Cable Length

Wiremap

Straight Cable Cross Cable

Both straight-through and crossover cables (10/100BASE,

1000BASE-T and 1000BASE-TX) can be checked.

Display Examples

Reversed

Pins 1 and 2 are reversed.

Transposed

Pins 3 and 6 have been

incorrectly paired with Pins

4 and 5.

Open

Pin 1 is open at a distance

7 meters from the LAN

cable tester.

Short

Pins 1 and 2 are shorted at

a distance 10 meters from

the LAN cable tester.

Split Pair

A very common mistake -

twist pairs Pins 3+6, and

Pins 4+5, have been incor-

rectly connected.

Caution!

Just connect a cable, and

press the TEST button

Check all parameters such as wiremap,

direction and cable length at a glance.

Extremely

Intuitive

Wide

LCD

Screen

PASS

FAIL

Cable Length

Direction

Have you ever had trouble

installing additional cables?

Take advantage of the conveniences oered by the tester’s

capabilities to check wiring while confirming multiple cable

destinations.

Up to 21 terminators can be connected (additional terminators

sold separately.) Convenient for conrming the connection desti-

nations of multiple cables.

You will never need to go back and forth

again just to change the terminators.

1 2 3

n Activating the NVP function is as simple as 1-2-3

Prepare a reference cable

using a known length

of the same type as that

to be measured (at least

100-meter length recom-

mended).

Preparation

The HIOKI 3665 can do the job for you properly and

accurately by also detecting split pairs.

To properly check LAN cable wiring,

a tester capable of detecting split pairs is indispensable.

Measure for cable length and detect the location of broken or short-circuited wires.

Locate up to 21 unique cable destinations.

Increased

Precision

Split pairs appear to be properly

connected to the untrained eye,

and cannot be detected with continuity

testing. OK!

How Can Split Pairs Affect the Network?

nCommunication speed can be suppressed - 100BASE signals may reach only 10BASE speeds.

nExcessive communication errors - data transfer may be intermittent or completely inhibited.

nCables miswired in this way are more susceptible to electrical noise.

Increased

Efciency

NVP (Nominal Velocity of Propagation) is the ratio of the speed of a signal in the cable relative to the speed of light

in a vacuum. NVP differs according to the type of cable and the manner in which the wire pairs are twisted, so mea-

surement accuracy can be enhanced by setting the NVP value for the particular type of cable to be measured.

On the Settings screen,

select “Length Adjust”.

Press the TEST button to

measure the (already known)

length of the reference cable.

Calibrate the display to the

measured reference cable.

Setting Finished

The NVP setting is a cable-length compensation function that

enhances the accuracy of cable length measurements.

Accuracy with NVP activated:

n± 4% rdg. ± 1m

(vs.previous HIOKI model: 15% rdg. ±1m)

Measurable cables Twisted-pair cable

100 Ω characteristic impedance, shielded and unshielded, CAT 3, 4, 5, 5e, 6 and 6A

Compatible connectors

RJ-45 plugs

Measurement Items

[Wiremap] Wiring condition and shielding can be confirmed using the HIOKI TERMINATOR 9690

Detectable errors: open, short, reversed, transposed, split pairs and other miswiring

[Cable Length]

Measurable lengths: 2 m to 300 m, 6.6 ft to 984 ft

Measurement accuracy: ±4% rdg. ±1 m, ±4% rdg. ±3.3 ft (condition of regulation: single wire)

Display resolution: 0.1 m

[Destination] Up to 21 cables can be identified using the supplied TERMINATOR 9690 and optional Models 9690-01 to

9690-04 to test multiple cables simultaneously

Display 128 × 64 dot matrix LCD (with backlight)

Functions

Auto Backlight: pressing a button turns the backlight on (it turns off automatically after about 20 seconds)

Beeper: sounds when pressing buttons and when measurement results are displayed

Energy-Saving Mode: enter into energy-saving mode after measurement (and resume when the TEST button is pressed)

Auto Power Save: the 3665 turns off automatically about 10 minutes after the last button press

Battery Check: Battery indicator blinks when voltage falls below 2.4 V

Unit Switch: Select between meters or feet

Compliance Standards Safety Standard: EN61010 Pollution Level 2

EMC Standard: EN61326

Allowable Input 3.3 V peak (between RJ-45 pins)

Operating Temperature & Humidity

0 to 40 °C, 80% RH or less, non-condensating

Storage Temperature & Humidity

–10 to 50 °C, 80% RH or less, non-condensating

Power supply LR6 (AA) alkaline batteries × 2

Maximum Power Consumption

1.4 VA

Operating Time Approx. 50 hours (measuring once per minute)

Dimensions and mass Approx. 85 mm (3.35 in) W × 130 mm (5.12 in) H × 33 mm (1.30 in) D, approx. 160 g (5.6 oz)

nSpecifications (Accuracy guaranteed for 1 year) @ 23 ±5 °C, 80% RH or less, non-condensating, with battery indicator unlit

TERMINATOR 9690-01 (IDs 1 to 5)

TERMINATOR 9690-02 (IDs 6 to 10)

TERMINATOR 9690-03 (IDs 11 to 15)

TERMINATOR 9690-04 (IDs 16 to 20)

CARRYING CASE 9249 (stores the 3665 and 9690 together)

nOptions

CARRYING CASE 9249

(for storing everything together)

nSupplied Accessories

TERMINATOR 9690

CARRYING CASE

(Stores the HiTESTER 3665 and TERMINATORs 9690)

CARRYING CASETERMINATOR 9690

TERMINATOR 9690-01

Model : LAN CABLE HiTESTER 3665

Model No. (Order Code)

(Note)

3665-20 (English model)

Accessories: Terminator 9690 ×1, Carrying case ×1, LR6 (AA) alkaline

battery ×2, Instruction manual ×1

HEADQUARTERS

81 Koizumi,

Ueda, Nagano 386-1192 Japan

https://www.hioki.com/

All information correct as of Mar. 4, 2022. Contents are subject to change without notice. 3665E7-23B Printed in Japan

DISTRIBUTED BY

Note: Company names and product names appearing in this brochure are trademarks or registered trademarks of various companies.

Andere Handbücher für 3665-20

Dieses Handbuch passt für folgende Modelle

Andere Hioki Prüfgeräte Handbücher

Hioki

Hioki 3281 Bedienungsanleitung

Hioki

Hioki RM3543 Bedienungsanleitung

Hioki

Hioki BT3563A Bedienungsanleitung

Hioki

Hioki 3143 Bedienungsanleitung

Hioki

Hioki 3030-10 Bedienungsanleitung

Hioki

Hioki 3455 Bedienungsanleitung

Hioki

Hioki 3455 Bedienungsanleitung

Hioki

Hioki 3290-10 Bedienungsanleitung

Hioki

Hioki FT6031 Bedienungsanleitung

Hioki

Hioki 9455 Bedienungsanleitung

Hioki

Hioki 3454-11 Bedienungsanleitung

Hioki

Hioki SM7810 Bedienungsanleitung

Hioki

Hioki FT3405 Bedienungsanleitung

Hioki

Hioki IM9201 Bedienungsanleitung

Hioki

Hioki ST5680 Benutzerhandbuch

Hioki

Hioki 3555 Bedienungsanleitung

Hioki

Hioki MR8827 Bedienungsanleitung

Hioki

Hioki MO HiTESTER 3452 Bedienungsanleitung

Hioki

Hioki 3169-21 Gebrauchsanweisung

Hioki

Hioki 3158 Bedienungsanleitung

Hioki

Hioki Power HiTester 3193 Bedienungsanleitung

Hioki

Hioki 3144-20 Bedienungsanleitung

Hioki

Hioki FT6031-03 Bedienungsanleitung

Hioki

Hioki ST5680 Bedienungsanleitung

Beliebte Prüfgeräte Handbücher anderer Marken

SMART

SMART KANAAD SBT XTREME 3G Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies BERT Serial Bedienungsanleitung

Agilent Technologies

Agilent Technologies N3280A Bedienungsanleitung

Lifeloc

Lifeloc R.A.D.A.R. Bedienungsanleitung

Fluke

Fluke T5-600 Bedienungs- und Montageanleitung

Mercury

Mercury TSL01 Bedienungsanleitung

MAHA

MAHA MBT Series Bedienungsanleitung

Fuji Electric

Fuji Electric P-61 Bedienungsanleitung

ETC

ETC SealerAtor Bedienungsanleitung

Skyfine

Skyfine ETHYWAY V2 Bedienungsanleitung

Appion

Appion G5 Twin Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 8159-0112A Bedienungsanleitung

BW Technologies

BW Technologies MicroDock II Bedienungsanleitung

Sun Nuclear

Sun Nuclear 1027 Bedienungsanleitung

Biomark

Biomark HPR LITE READER Bedienungsanleitung

Ashcroft

Ashcroft ATE-100 Bedienungsanleitung

Rohde & Schwarz

Rohde & Schwarz RTA4000 Bedienungsanleitung

Ritmix

Ritmix RAT-701 Bedienungsanleitung