Hioki RM3542 Bedienungsanleitung

Thank you for purchasing the HIOKI RM3542/3542-01 Resistance HiTester. This guide describes basic screen operations

and comparator setting procedures. Before using the instrument the first time, please read the operating manual.

RM3542, RM3542-01

RESISTANCE HiTESTER

Operation Guide

November 2009 Edition 1 RM3542A983-00 09-11H Printed in Japan

Select and change display screens and settings

omparator Results

(

COMP indicator LEDs)

iMeasured Value is

above Upper limit

NPass (meets criteria)

oMeasured Value is

below Lower limit

Numerical value

entry and related

settings

Absolute or relative value

ower On/Off

•

Unlit: power off

(while power is not supplied)

•

Red light: power off

(while power is supplied)

•

Green light: power on

Measurement cable jacks

Decision criteria

Measurement decision criteria settings

(Comparator function)

REF% Decide by reference value and tolerance (%)

ABS Decide by specified threshold values

Measurement Screen

(MISC MEAS MEAS SETTINGS)

Measurement Settings

DELAY1 Adjust the delay from probing to trigger input

DELAY2 Adjust measurement object electrical response

INT(FAST/ MED/ SLOW) Make fine adjustment to integration time

CONT CHECK Contact check threshold settings

CONT IMP Contact Improver function settings

VOLT MONITOR Voltage level monitor function settings

CURRENT MODE Current mode setting (CONT/ PULSE)

(MISC DATA DATA SETTINGS)

Data Settings

AUTO MEMORY Turn Auto-Memory on/off

STATISTICS Statistical calculation on/off

DATA OUT Automatically output measured value

(MISC SYSTEM SYSTEM) System Settings

SET MONITOR Turn two-instrument setting comparison on/off

PROBE CHECK Turn probe short-circuit detection on/off

RETRY Retry function on/off

TRIG EDGE (External I/O) Set trigger rising/falling edge

EOM (External I/O) Set EOM (end-of-measurement) signal

INTERFACE Communications interface settings

LOW POWER Low-power resistance component measurement on/off

JUDGE BEEP Comparator beeper settings

KEY BEEP Key beeper on/off

CLOCK(Y-M-D) Set internal clock

LINE FREQ Set power source frequency

CONTRAST Adjust screen contrast

BACKLIGHT Adjust screen backlight

RESET Initialize

ADJUST Instrument Adjustment

Basic Settings Screen

Detailed Settings

Screens

TRG Change trigger source (INT/EXT)

RANGE Change range (100mΩto 100MΩ)

SPEED Change measurement speed (FAST/MED/

SLOW)

0ADJ Turn zero-adjust on/off

COMP Turn comparator on/off

LOCK Enable/disable key lock (OFF/FULL/MENU)

Measurementscreenoperationsare

shown on the back of this sheet.

Screen Organization

Setting screen

Set reference value

(example 10.5Ω)

Change

sign:

Return to

Measurement

screen

Set upper tolerance

(example +4.5%)

Set lower tolerance

(example -4.5%)

Decide According to

Reference Value and Tolerance

When setting the upper tolerance, the

lower tolerance is automatically set to

its negative equivalent. Change the

setting as needed.

Select item

Cancel:

Setting Comparator Decision Criteria for Measured Values

REF% Mode

Change

numerical value:

Return to

Measurement

screen

Decide According to

Upper/Lower Thresholds

Set upper thresholds

(example 150mΩ)

Set lower thresholds

(example 50mΩ)

Setting screen Select item

Change

numerical value: Cancel:

ABS Mode

+OvrRng

-OvrRng

Contact Check Fault

Indicates possible contact fault or broken

cable.

Voltage Level Monitor Fault

Probe contact may be unstable, or electri-

cal noise ingress may be present.

No Measurement Data

No measurement value is present imme-

diately after power on or after changing

range. Errors with other causes can pre-

vent display of measured values.

Measurement Fault (Error) Indicators

Measurement Screen Indicators

Trigger Source

INT: Internal trigger

EXT: External trigger

Measurement

range Measurement speed

Appears only when OVC is enabled

(OVC: Offset Voltage Compensation)

Appears only when the Low-Power

Resistance function is enabled

Key-Lock State

F.LOCK: Changes to settings are disabled

M.LOCK: All except comparator settings are disabled

Zero-adjust (ON)

Remote control

C.E. Hi

C.E. Lo

C.E. Volt

- - - - - - -

Cancel key-lock

(hold 1s)

PRINT Prints measured value

(Enabled when PRINT is selected as the INTERFACE

setting on the SYSTEM screen) PRINT Prints statistical data

(Enabled when PRINT is selected as the INTER-

FACE setting on the SYSTEM screen)

STAT Displays statistical calculation results

(Enabled when ON is selected as the STATISTICS set-

ting on the DATA screen) UNDO Deletes the previously stored measurement

and calculation result (only the most recent

measurement can be deleted)

NUMBER

Sets the number of measurements for Auto-Memo-

ry mode

(Enabled when ON is selected as the AUTO MEMORY

setting on the DATA screen)

ALLCLR Deletes all memories and calculations

Enable local

control

Tenkey Input Enabled

Change Settings

Out of Range (over- or under-range)

The measured value is above or below

the measurement range, or open device.

Andere Handbücher für RM3542

Dieses Handbuch passt für folgende Modelle

Andere Hioki Prüfgeräte Handbücher

Hioki

Hioki IR4056 Bedienungsanleitung

Hioki

Hioki 3805-50 Bedienungsanleitung

Hioki

Hioki 7016 Bedienungsanleitung

Hioki

Hioki TS2400 Bedienungsanleitung

Hioki

Hioki 3281 Bedienungsanleitung

Hioki

Hioki 3550 Bedienungsanleitung

Hioki

Hioki 3169-20 Bedienungsanleitung

Hioki

Hioki IR4051 Bedienungsanleitung

Hioki

Hioki 3143 Bedienungsanleitung

Hioki

Hioki FT3405 Bedienungsanleitung

Hioki

Hioki ST5520-01 Bedienungsanleitung

Hioki

Hioki 3560 Bedienungsanleitung

Hioki

Hioki MEMORY HiCORDER 8855 Gebrauchsanweisung

Hioki

Hioki RM3542 Bedienungsanleitung

Hioki

Hioki 3665-20 Bedienungsanleitung

Hioki

Hioki 3444 Bedienungsanleitung

Hioki

Hioki FT6031-03 Bedienungsanleitung

Hioki

Hioki 3522-50 Bedienungsanleitung

Hioki

Hioki 3665-20 Bedienungsanleitung

Hioki

Hioki ST5680 Bedienungsanleitung

Hioki

Hioki 3454-11 Bedienungsanleitung

Hioki

Hioki 3118 Bedienungsanleitung

Hioki

Hioki RM3543 Bedienungsanleitung

Hioki

Hioki BT3554 Bedienungsanleitung

Beliebte Prüfgeräte Handbücher anderer Marken

SMART

SMART KANAAD SBT XTREME 3G Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies BERT Serial Bedienungsanleitung

Agilent Technologies

Agilent Technologies N3280A Bedienungsanleitung

Lifeloc

Lifeloc R.A.D.A.R. Bedienungsanleitung

Fluke

Fluke T5-600 Bedienungs- und Montageanleitung

Mercury

Mercury TSL01 Bedienungsanleitung

MAHA

MAHA MBT Series Bedienungsanleitung

Fuji Electric

Fuji Electric P-61 Bedienungsanleitung

ETC

ETC SealerAtor Bedienungsanleitung

Skyfine

Skyfine ETHYWAY V2 Bedienungsanleitung

Appion

Appion G5 Twin Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 8159-0112A Bedienungsanleitung

BW Technologies

BW Technologies MicroDock II Bedienungsanleitung

Sun Nuclear

Sun Nuclear 1027 Bedienungsanleitung

Biomark

Biomark HPR LITE READER Bedienungsanleitung

Ashcroft

Ashcroft ATE-100 Bedienungsanleitung

Rohde & Schwarz

Rohde & Schwarz RTA4000 Bedienungsanleitung

Ritmix

Ritmix RAT-701 Bedienungsanleitung