Hirschmann BRS20-0400 Series Bedienungsanleitung
Installation BRS20/30/40/50
Release
02
11/2018
Technical support
https://hirschmann-support.belden.com
User Manual
Installation
Industrial Ethernet BOBCAT Rail Switch
BRS20/30/40/50
11/15/18 Installation BRS20/30/40/50
Release
02
11/2018
The naming of copyrighted trademarks in this manual, even when not specially indicated, should
not be taken to mean that these names may be considered as free in the sense of the trademark
and tradename protection law and hence that they may be freely used by anyone.
© 2018 Hirschmann Automation and Control GmbH
Manuals and software are protected by copyright. All rights reserved. The copying, reproduction,
translation, conversion into any electronic medium or machine scannable form is not permitted,
either in whole or in part. An exception is the preparation of a backup copy of the software for
your own use.
The performance features described here are binding only if they have been expressly agreed
when the contract was made. This document was produced by Hirschmann Automation and
Control GmbH according to the best of the company's knowledge. Hirschmann reserves the right
to change the contents of this document without prior notice. Hirschmann can give no guarantee
in respect of the correctness or accuracy of the information in this document.
Hirschmann can accept no responsibility for damages, resulting from the use of the network
components or the associated operating software. In addition, we refer to the conditions of use
specified in the license contract.
You can get the latest version of this manual on the Internet at the Hirschmann product site
(www.hirschmann.com).
Hirschmann Automation and Control GmbH
Stuttgarter Str. 45-51
72654 Neckartenzlingen
Germany
Installation BRS20/30/40/50
Release
02
11/2018 3
Contents
Safety instructions 6
About this manual 14
Key 15
1 Description 16
1.1 General device description 16
1.2 Device name and product code 18
1.3 Device views 22
1.3.1 Front view 22
1.3.2 Rear view 30
1.4 Power supply 31
1.4.1 Supply voltage with characteristic value T 31
1.4.2 Supply voltage with characteristic value F 31
1.5 Ethernet ports 31
1.5.1 10/100 Mbit/s twisted pair port 31
1.5.2 10/100/1000 Mbit/s twisted pair port 31
1.5.3 100 Mbit/s F/O port 32
1.5.4 100/1000 Mbit/s F/O port 32
1.5.5 100/1000/2500 Mbit/s F/O port 33
1.6 Display elements 34
1.6.1 Device state 34
1.6.2 Port status 35
1.7 Management interfaces 37
1.7.1 Signal contact 37
1.7.2 USB-C interface 38
1.7.3 Digital input 39
2 Installation 40
2.1 Checking the package contents 40
2.2 Installing and grounding the device 40
2.2.1 Installing the device onto the DIN rail 40
2.2.2 Grounding the device 41
2.3 Installing an SFP transceiver (optional) 42
4Installation BRS20/30/40/50
Release
02
11/2018
2.4 Connecting the terminal blocks 42
2.4.1 Power supply 42
2.4.2 Signal contact (optional) 45
2.4.3 Digital input (optional) 46
2.5 Operating the device 47
2.6 Connecting data cables 48
2.7 Filling out the inscription label 48
2.8 Making basic settings 48
3 Monitoring the ambient air temperature 50
4 Maintenance and service 51
5Disassembly 52
5.1 Removing an SFP transceiver (optional) 52
5.2 Removing the device 53
6 Technical data 54
6.1 General data 54
6.2 Supply voltage 54
6.3 Power consumption/power output 56
6.4 Signal contact 56
6.5 Digital input 57
6.6 Climatic conditions during operation 58
6.7 Climatic conditions during storage 58
6.8 Dimension drawings 59
6.9 Stability 61
6.10 Electromagnetic compatibility (EMC) 61
6.11 Network range 63
6.11.1 10/100/1000 Mbit/s twisted pair port 63
6.11.2 Fast Ethernet SFP transceiver 63
6.11.3 Gigabit Ethernet SFP transceiver 65
6.11.4 2.5 Gigabit Ethernet SFP transceiver 67
6.11.5 Bidirectional Fast Ethernet SFP transceiver 67
6.11.6 Bidirectional Gigabit Ethernet SFP transceiver 68
6.12 Derating due to SFP transceiver 69
Installation BRS20/30/40/50
Release
02
11/2018 5
6.12.1 Fast Ethernet SFP transceiver 69
6.12.2 Gigabit Ethernet SFP transceiver 70
6.12.3 2.5 Gigabit Ethernet SFP transceiver 71
6.12.4 Bidirectional Fast Ethernet SFP transceiver 72
6.12.5 Bidirectional Gigabit Ethernet SFP transceiver 72
7 Scope of delivery 73
8 Accessories 74
8.1 General accessories 74
8.2 Fast Ethernet SFP transceiver 74
8.3 Gigabit Ethernet SFP transceiver 75
8.4 2.5 Gigabit Ethernet SFP transceiver 75
8.5 Bidirectional Fast Ethernet SFP transceiver 76
8.6 Bidirectional Gigabit Ethernet SFP transceiver 76
9 Underlying technical standards 77
A Further support 78
6Installation BRS20/30/40/50
Release
02
11/2018
Safety instructions
General safety instructions
You operate this device with electricity. Improper usage of the device
entails the risk of physical injury or significant property damage. The
proper and safe operation of this device depends on proper handling
during transportation, proper storage and installation, and careful
operation and maintenance procedures.
Before connecting any cable, read this document, and the safety
instructions and warnings.
Operate the device with undamaged components exclusively.
The device is free of any service components. In case of a damaged
or malfunctioning device, turn off the supply voltage and return the
device to Hirschmann for inspection.
Certified usage
Use the product only for the application cases described in the
Hirschmann product information, including this manual.
Operate the product only according to the technical specifications.
See “Technical data” on page 54.
Connect to the product only components suitable for the requirements
of the specific application case.
WARNING
UNCONTROLLED MACHINE ACTIONS
To avoid uncontrolled machine actions caused by data loss, configure all
the data transmission devices individually.
Before you start any machine which is controlled via data transmission, be
sure to complete the configuration of all data transmission devices.
Failure to follow this instruction can result in death, serious injury, or
equipment damage.
Installation BRS20/30/40/50
Release
02
11/2018 7
Installation site requirements
Install this device solely in a switch cabinet or in an operating site with
restricted access, to which maintenance staff have exclusive access.
When you are selecting the installation location, make sure you
observe the climatic threshold values specified in the technical data.
Use the device in an environment with a maximum pollution degree
that complies with the specifications in the technical data.
See “Technical data” on page 54.
Qualification requirements for personnel
Only allow qualified personnel to work on the device.
Qualified personnel have the following characteristics:
Qualified personnel are properly trained. Training as well as practical
knowledge and experience make up their qualifications. This is the
prerequisite for grounding and labeling circuits, devices, and systems
in accordance with current standards in safety technology.
Qualified personnel are aware of the dangers that exist in their work.
Qualified personnel are familiar with appropriate measures against
these hazards in order to reduce the risk for themselves and others.
Qualified personnel receive training on a regular basis.
Device casing
Only technicians authorized by the manufacturer are permitted to open
the casing.
Shielding ground
The shielding ground of the connectable twisted pair cables is connected
to the ground connection as a conductor.
Beware of possible short circuits when connecting a cable section with
conductive shielding braiding.
WARNING
FIRE HAZARD
Install the device in a fire enclosure as per EN 62368 or EN 60950-1 if you
are connecting it to a power supply >100 W (PS3) or >NEC Class 2.
Failure to follow these instructions can result in death, serious injury,
or equipment damage.
8Installation BRS20/30/40/50
Release
02
11/2018
Grounding the device
The housing is grounded via the separate ground screw on the bottom left
of the front side of the device.
Ground the device before connecting any other cables.
Disconnect the grounding only after disconnecting all other cables.
Requirements for connecting electrical wires
Before connecting the electrical wires, always verify that the
requirements listed are complied with.
Requirements for connecting the signal contact
Before connecting the signal contact, always verify that the requirements
listed are complied with.
Requirements for connecting the supply voltage
Before connecting the supply voltage, always verify that the requirements
listed are complied with.
The following requirements apply without restrictions:
The electrical wires are voltage-free.
The cables used are permitted for the temperature range of the application case.
Relevant for North America:
Exclusively use 60/75 °C (140/167 °F) or 75 °C (167 °F) copper (Cu) wire.
The AC power source is electrically isolated from the ground potential. The power source
is current-limited or there is a fuse in the supply line. Regarding the properties of this fuse:
See “Technical data” on page 54.
The following requirements apply without restrictions:
The connected voltage complies with the requirements for a safety extra-low voltage
(SELV) or ES1 as per IEC/EN 62368-1.
The connected voltage is limited by a current limitation device or a fuse.
Observe the electrical threshold values for the signal contact.
See “Technical data” on page 54.
Prerequisites:
All of the following requirements are complied with:
The supply voltage corresponds to the voltage specified on the type plate of the device.
The power supply complies with the requirements for a safety extra-low voltage (SELV) or
ES1 as per IEC/EN 62368-1.
The power supply has an easily accessible disconnecting device (for example a switch or
a plug). This disconnecting device is clearly identified. So in the case of an emergency, it is
clear which disconnecting device belongs to which power supply cable.
The wire diameter of the power supply cable is at least 0.75 mm² (North America: AWG18)
on the supply voltage input.
The cross-section of the ground conductor is the same size as or bigger than the cross-
section of the power supply cables.
The following requirements apply alternatively:
Relevant when the device is supplied via 1 voltage input:
Installation BRS20/30/40/50
Release
02
11/2018 9
Supply voltage
The supply voltage is connected to the device casing through protective
elements exclusively.
LED or laser components
LED or LASER components according to IEC 60825-1 (2014):
CLASS 1 LASER PRODUCT
CLASS 1 LED PRODUCT
National and international safety regulations
Verify that the electrical installation meets local or nationally applicable
safety regulations.
All of the following requirements are complied with:
Supply with DC voltage:
A fuse suitable for DC voltage is located in the positive conductor of
the power supply.
The negative conductor is on ground potential.
Regarding the properties of this fuse:
See “Technical data” on page 54.
Device variants
featuring supply
voltage with
characteristic value F
Supply with AC voltage:
The AC power source is electrically isolated from the ground
potential. The power source is current-limited or there is a fuse in the
supply line. Regarding the properties of this fuse:
See “Technical data” on page 54.
Relevant when the device is supplied via 2 voltage inputs:
All of the following requirements are complied with:
Supply with DC voltage:
A fuse suitable for DC voltage is located at both voltage inputs in the
positive conductor of the power supply.
The negative conductor is on ground potential at both voltage inputs.
Regarding the properties of this fuse:
See “Technical data” on page 54.
Device variants
featuring supply
voltage with
characteristic value F
Supply with AC voltage:
The AC power source is electrically isolated from the ground
potential. The power source is current-limited or there is a fuse in the
supply line. Regarding the properties of this fuse:
See “Technical data” on page 54.
Prerequisites:
10 Installation BRS20/30/40/50
Release
02
11/2018
Relevant for use in explosion hazard areas (Hazardous
Locations, Class I, Division 2)
2UGLQDU\/RFDWLRQ
1RQ+D]DUGRXV$UHD
1RQ([SORVLYH$WPRVSKHUH
([SORVLYH$WPRVSKHUH
&ODVV, LYLVLRQ*URXSV$
%&
+D]DUGRXV/RFDWLRQ
7HPSHUDWXUH&RGH7
$PELHQW7HPSHUDWXUHUDWLQJ
&DSDFLW\&D&L&&DEOH,QGXFWLYLW\/D/L/&DEOH
:$51,1*
/Dí/L&DEOH/
&DEOH/
&Dí&L&DEOH&
&DEOH&
Dieses Handbuch passt für folgende Modelle
16
Inhaltsverzeichnis
Andere Hirschmann Schalten Handbücher
Hirschmann
Hirschmann GRS103 Series Bedienungsanleitung
Hirschmann
Hirschmann SPIDER 5TX Handbuch
Hirschmann
Hirschmann OCTOPUS 8M Series Bedienungsanleitung
Hirschmann
Hirschmann GigaLION-24TP Bedienungsanleitung
Hirschmann
Hirschmann ETHERNET IP67 Bedienungs- und Montageanleitung
Hirschmann
Hirschmann MACH1000 Series Bedienungsanleitung
Hirschmann
Hirschmann PowerLION-24TP Bedienungsanleitung
Hirschmann
Hirschmann OCTOPUS OS20 Bedienungsanleitung
Hirschmann
Hirschmann GREYHOUND GRS1020 Bedienungsanleitung
Hirschmann
Hirschmann MACH 3001 Handbuch
Hirschmann
Hirschmann OCTOPUS 8TX-EEC Bedienungsanleitung
Hirschmann
Hirschmann MAR1042 Bedienungsanleitung
Hirschmann
Hirschmann RS20 series Bedienungsanleitung
Hirschmann
Hirschmann RS20 series Bedienungsanleitung
Hirschmann
Hirschmann PowerMICE Bedienungsanleitung
Hirschmann
Hirschmann MACH1040 Bedienungsanleitung
Hirschmann
Hirschmann 943 686-003 Bedienungsanleitung
Hirschmann
Hirschmann MSM20 Bedienungsanleitung
Hirschmann
Hirschmann RSPE 30 Bedienungsanleitung
Hirschmann
Hirschmann RS20 series Bedienungsanleitung
