Hitachi CP-WU13K Bedienungsanleitung

Projector

CP-WU13K

User Manual

Thank you for purchasing this product. Please

read this manual before you operate your

projector. Save it for future reference.

Warning, Notices and Safety Instructions 4

Notice 4

Description pertaining to FCC Rules Part 15 4

About Waste Electrical and Electronic Equipment 5

Special Care for Laser Beams! 5

Sun light Warning 5

Never look into the projector light source directly 5

Do not turn off the projector by unplugging the power cord. 6

Electric shock 6

Do not overload wall outlets/extension cords 6

Cleaning 6

Dampness, smoke, steam, dust, high temperature and direct

exposure to sunlight 6

Ventilation 7

Filter 7

Intrusion of foreign objects 7

Carrying the projector 7

Please install the projector on an even and stable surface 7

Servicing 7

Changing parts 8

Power cord 8

Notices you should read prior to the installation of the

projector 8

Safety issues related to the lamp 8

Take frequent breaks to let your eyes rest 8

Installation environment for the projector 8

Do not tilt the projector more than 10 degrees. 9

Congurations for projector operation at high altitudes 9

Keep the projector's ventilation inlets and outlets free from

obstructions 9

Protect the projector with care 9

Name and quantity of toxic/hazardous substances/elements

contained in the product 10

Projector parts and functions 11

Front view 11

Bottom view 13

Range of effective remote control signal reception 14

Installing batteries in the remote control 14

Installation the projector. 15

1. Orient the projector towards the screen 15

2. Connect the power cord to the projector 15

3. Connect the projector to your PC and ip the switch

to “I” to turn on the power. 15

4. Remove the lens PU foam on the projector before

starting it up. 15

5. Adjusting the projector's angle 16

6. Adjusting focus and zoom. 16

7. Correcting keystoning caused by projection angle 17

8. Turning off the projector 17

Throw distance 18

Modes of installation 18

Frontal projection - desktop installation 18

Frontal projection - ceiling mode 19

Rear projection - desktop

installation 19

Rear projection - ceiling installation 19

Rear projection - submersive installation 19

Horizontal and vertical lens shift 20

Moving the lens vertically 20

Moving the lens horizontally 20

Connecting the projector to other devices 21

HDMI / DVI connection 21

12V Trigger connection 21

RGB connection 22

COMPONENT connection 23

STEREO DVI Connection 23

Turning on the projector 24

Changing OSD language 24

Adjusting screen orientation 25

Front projection - ceiling mode 25

Rear projection - desktop installation 26

Rear projection - ceiling mode 26

Adjusting the projector lens 26

Remote control 27

OSD Menu Tree 29

INDEX

OSD Description 31

INPUT 31

Input Selection 31

Input Conguration 31

Input Locking 32

Auto Power Off 32

Auto Power ON 32

No Signal 32

Auto Image Adjust 32

IMAGE 33

Contrast 33

Brightness 34

Sharpness 35

Noise Reduction 35

Color Temperature 36

Input Balance 36

Aspect Ratio 37

Timings 38

Auto Image 39

LAYOUT 40

Zoom 40

Main Select 41

PIP Select 41

PIP Position 41

PIP 41

LAMP 42

Mode 42

LAMPS 42

High Altitude Mode 43

Power 43

Lamp1 Status 43

Lamp2 Status 43

Lamp1 Run Time 43

Lamp2 Run Time 43

ALIGNMENT 44

Rear Projection 44

Ceiling Mode 44

Lens Control 44

Dynamic Contrast 44

Gamma 45

Internal Patterns 45

Color Space 45

Lens To Midposition 45

Warp 46

Blanking 47

Edge blend 48

CONTROL 50

IR Address 50

Eco Network Power 50

Network 51

Menu Position 51

Start Up Logo 51

Start Up Chime 51

Button 1~5 51

Trigger1 ~2 52

Auto Source 52

Language 52

SERVICE 53

Service 53

Lamp Hour Reset 53

Blue Only 53

Factory Reset 53

Lamp and Filter Maintenance 54

Lamp replacement 54

Replace the lter 55

Simple troubleshooting and denition of the

LED indicators 57

LED STATUS 58

STAND BY 58

ON 58

ERROR 58

Warning 59

Specications 60

Supported Signal Input Modes 61

SDI formats 62

DVI dual-link for 3D 62

Dimensions 63

Communication settings 64

RS-232 Communication 64

Connection 64

1. Protocol 65

2. Command format 65

3. Response code / Error code 66

RS-232 Communication command table 67

Disclaimer 73

Warranty and after-service 73

Warning, Notices and Safety Instructions

Notice

Please write down your projector model number and serial number and keep the information for

maintenance purposes in the future. Should the equipment be lost or stolen, the information could also

be used for the police report.

Model number:

Serial number:

Please check the accessories that come with the projector with the following list. Should you nd any

missing accessory, contact your dealer immediately.

1. AC Power Cord US 110V*1

2. AC Power Cord US 200V*1

3. AC Power Cord EU*1

4. Remote control *1

5. AA battery *2

6. CD-ROM *1

7. Printed Manual *1

8. EAC Document *1

9. EU Recycle Sheet *1

10. WEEE Manual *1

11. RS232 cable(cross) *1

Description pertaining to FCC Rules Part 15

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two

conditions: (1) this device may not cause harmful interference, and (2) this device must accept any

interference received, including interference that may cause undesired operation.

This device has been tested and found to comply with the limits for a Class A digital device, pursuant

to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against

harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy. If not installed and used in

accordance with the instructions, may cause harmful interference to radio or television reception.

However, there is no guarantee that interference will not occur in a particular installation. If this

equipment does cause interference to radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged to try to correct the interference by one or

the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment in to an outlet on a circuit different from that to which the receiver is

connected.

• Consult the dealer or an experienced radio/TV technician for help.

Warning, Notices and Safety Instructions

CAUTION:

Changes or modications not expressly approved by the manufacturer void the user’s authority to

operate the equipment.

This Class A digital apparatus meets all requirements of the Canadian ICES-003 Standards.

Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.

About Waste Electrical and Electronic Equipment

The mark is in compliance with the Waste Electrical and Electronic Equipment Directive

2002/96/EC (WEEE).The mark indicates the requirement NOT to dispose the equipment including

any spent or discarded batteries or accumulators as unsorted municipal waste, but use the return and

collection systems available. If the batteries or accumulators included with this equipment, display the

chemical symbol Hg, Cd, or Pb, then it means that the battery has a heavy metal content of more than

0.0005% Mercury or more than, 0.002% Cadmium, or more than 0.004% Lead.

This is a Class A product. In a domestic environment this product may cause radio interference in which case the user

may be required to take adequate measures

The lamp(s) in this product contain mercury. This product could contain other electronic wastes

that might be hazardous if not handled properly. Please consult your local/state/federal regulations

regarding disposal or recycling.

Hg For more information, please contact Electronic Industries Alliance (WWW.EIAE.ORG).

For information on proper lamp handling, visit WWW.LAMPRECYCLE.ORG.

Special Care for Laser Beams!

Special care should be considered when DLP projectors and high power laser equipment are used in

the same room as.

Direct or indirect hit of a laser beam on to the projector lens can severely damage the Digital Mirror

Devices (DMD™).

Sun light Warning

Avoid using the CP-WU13K in direct sun light.

Sun light on the projector lens can severely damage the Digital Mirror Devices (DMD™).

Never look into the projector light source directly

This equipment contains a high brightness light source and a portion of the

light emitted by the projector is ultraviolet light. Never look into the projector

light source directly and pay special attention to prevent children from

looking into the projector light source as it can damage their eyes.

AVOID EYE CONTACT TO THE LIGHT

Warning, Notices and Safety Instructions

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

The lightning flash with an arrowhead within a triangle

is intended to tell the user that inside this product

may cause risk of electrical shock to persons.

The exclamation point within a triangle is intended to tell

the user that important operating and/or servicing instructions

are included in the technical documentation for this equipment.

CAUTION / TO REDUCE THE RISK OF ELECTRIC SHOCK

DO NOT REMOVE COVER(OR BACK)

NO USER-SERVICEABLE PARTS INSIDE

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL

Do not turn off the projector by unplugging the power cord.

Under normal operations, be sure to use the SOFT POWER button to turn off the projector. And as

such, avoid shutting off AC power to turn off the projector since it could lead to lamp malfunctioning

or damage.

Electric shock

To protect your projector, avoid turning on the projector during lightning storms and unplug it from

the wall outlet. This will prevent sudden electrical surges caused by the lightning from damaging the

projector.

Do not overload wall outlets/extension cords

Pay attention to the current load of the outlet you are using, be it wall outlet or extension cord outlet to

prevent re or electric shock.

Cleaning

When cleaning the projector, be sure to unplug it from the wall outlet to prevent electric shock.

Do not use liquid or aerosol cleaners. Use a dry/damp cloth with excessive moisture removed for

cleaning. Be sure to use cleaning cloth designed to clean monitors for the projector to prevent damages

to the projector casing due to abrasion.

Dampness, smoke, steam, dust, high temperature and direct exposure

to sunlight

Do not operate the projector in environments where it could be expose to dampness, smoke, steam,

dust, high temperature or direct sunlight. For example: bathroom, kitchen, adjacent to washing

machine, damp basement rooms, electric heaters or similar environments. Keeping or operating the

projector in the above-mentioned environment could lead to discoloration, mold formation, grease or

damages to the projector.

Warning, Notices and Safety Instructions

Ventilation

The projector case is designed with slots and openings to remove the heat inside the projector so that it

will not overheat and damage the components. Be sure to operate the projector in an environment with

ideal ventilation and don't operate it on a sofa, rug or other closed-in environments that could obstruct

ventilation.

Filter

Make sure to clean or replace the lter when it is required to keep the air intake clear of dust, and

prevent possible over temperature issue of the projector due to the clog of lter. Please refer to Page 55

for details of lter replacement procedure.

Intrusion of foreign objects

Be sure to keep all foreign objects away from entering the projector because it could be exposed to

hazardous voltages and cause parts to short circuit. This could in turn lead to re hazard or electric

shock. Examples of foreign objects include: cockroach, screws, liquid and so forth.

In addition, never spill liquid into the projector.

Carrying the projector

When moving the projector on a cart, be sure to handle the cart with care

as abrupt stops, jolts of excessive force or uneven ground could lead the projector to topple.

Please install the projector on an even and stable surface

Avoid placing the projector on unstable cart, tripod, table and so forth to prevent the projector from

falling, becoming damaged or causing injuries.

Servicing

Should you encounter problem with the projector, please seek assistance from your local dealer or

qualied service personnel. Do not attempt to service the projector yourself so that you would not be

exposed to high voltage or other potential hazards.

Should you encounter any of the following situation, please unplug your projector from the wall outlet

and contact a qualied service personnel for assistance:

• Damaged power cord or power plug.

• If a foreign object has fallen into the projector or if you have spilled water or other liquid into the

projector.

• If the projector has been dropped accidentally or damaged.

• If you experience noticeably poor performance or malfunctioning with the projector despite having

followed instructions for normal operation.

Warning, Notices and Safety Instructions

Changing parts

Should any part of the projector be damaged, check with your servicing personnel that only

manufacturer certied parts were used for replacement. Used of non-certied parts may result in

damages to the projector or hazards such as re or electric shock. After changing parts, be sure to

remind the servicing personnel to perform safety inspections to ensure that the projector operates

nor mally.

Power cord

Don't place the projector where the cord can be walked on. This may result in fraying or damage to

the power cord, especially at the plug and the point of connection between the power cord and the

projector.

Please use the power cord that comes with the projector or the type of power cord specied for

the projector (refer to the descriptions printed on the power cord). If you are not sure of the power

available at the region you are in, consult your local power company to prevent damages to the

projector due to the use of wrong power cord or potential re hazards due to current overload.

Depending on the country and region you are in, the voltage and type of socket of the wall outlet may

be different from the projector. If you are unable to t the power plug into the wall outlet, contact your

local dealer and do not remove the extra pin on the power plug to forcibly t it to the socket at the risk

of your own safety.

Notices you should read prior to the installation of the projector

Safety issues related to the lamp

The lamp used in this projector contains mercury. Should the lamp be broken, please be careful when

handling the glass shards and keep the surrounding environment well ventilated. Be sure to wear a

mask that offers adequate protection before cleaning up to prevent inhaling mercury vapor that could

cause bodily harm. For instructions on lamp replacement, refer to " Page 7 : Lamp replacement ".

Take frequent breaks to let your eyes rest

Prolonged viewing of the projector screen could strain your eyes. Please be sure to rest your eyes

adequately.

Installation environment for the projector

You should avoid installing the projector at place of excessive dampness, dust or smoke. If installation

in such environment is unavoidable, be sure to have the interior of the projector

cleaned routinely to prolong the projector's lifecycle. Cleaning of the projector's interior should only be

performed by qualied service personnel dispatched by your local dealer and you should not attempt

to clean the inside of the projector by yourself.

If other light source is directly projected onto the projector screen, the color of the image from the

projector will appear to be pale and the image quality will be lower. In addition, your eyes would be

more prone to fatigue. Therefore, it is recommended that the projector be installed in places without

direct exposure to sunlight or other sources of intense light.

The ideal operating temperature range for the projector is between 0°C ~ 40°C (32°F ~ 104°F)

The ideal storage temperature range for the projector is between -20ºC ~ 60°C (-4°F ~ 140°F)

Warning, Notices and Safety Instructions

Do not tilt the projector more than 10 degrees.

The maximum tilt angle for the projector is 10 degrees.

When the projector is tilted more than 10 degrees, it will shorten the life of the projector lamp and

may lead to other unpredictable damages.

Can’t >10°

Congurations for projector operation at high altitudes

When operating the projector at higher altitudes, be sure to manually set the fan mode to "High" or

it could shorten the life of the optical system in the projector. High altitude is dened as places being

1500 meters (4900 feet) or higher.

Please refer to " Page 43 : High Altitude Mode ".

Keep the projector's ventilation inlets and outlets free from obstructions

Be sure to keep objects for no less than 30cm away from the ventilation inlets and outlets of the

projector and note the direction of air ow at the designated spot of installation. Do not let the hot air

released from the outlet ow back to the inlet as it will prevent proper cooling and lead to damage of

the projector's internal structure.

In the event of high temperature due to malfunctioning of the internal cooling fan caused by clogging at the

ventilation inlets and outlets, the projector will activate its automatic protection mode and shutdown. When

this happens, it does not necessary mean that the equipment is malfunctioning. Try to unplug the power cord

from the wall outlet and wait for approximately 15 minutes before operating the projector again (remember

to remove the objects that have caused poor ventilation so that the projector will not go into the protection

mode again). Please refer to " Page 58 : LED STATUS ".

Description: The regulation of temperature inside the projector by the cooling fan is automatic. And as such,

the sound of cooling fan changing its operating speed does not imply that a problem has occurred with the

projector.

Protect the projector with care

When placing the projector at a high position, be sure to secure the projector rmly so that it would

not fall and cause injuries. Take care to protect the projector's lens from collision, abrasion or other

damages. Be sure to close the lens cover or cover the projector with a dust cover if you need to store

the projector or if it will not be used for an extended time.

Warning, Notices and Safety Instructions

Name and quantity of toxic/hazardous substances/elements contained

in the product

Andere Handbücher für CP-WU13K

Inhaltsverzeichnis

Andere Hitachi Projektor Handbücher

Hitachi

Hitachi Performa CP-RS55 Bedienungsanleitung

Hitachi

Hitachi CP-X3010Z series Bedienungsanleitung

Hitachi

Hitachi CP-X450 series Bedienungsanleitung

Hitachi

Hitachi CP-X10000 Series Bedienungsanleitung

Hitachi

Hitachi LP-WU6600 Bedienungsanleitung

Hitachi

Hitachi CP-X2 series Leitfaden

Hitachi

Hitachi CP-RX70(M1-20EN) Bedienungsanleitung

Hitachi

Hitachi MP-EU5002 Bedienungsanleitung

Hitachi

Hitachi PJ1065 Bedienungsanleitung

Hitachi

Hitachi CP-X2530WN Bedienungsanleitung

Hitachi

Hitachi CP-CW251WN Bedienungsanleitung

Hitachi

Hitachi EDS-3170A Bedienungsanleitung

Hitachi

Hitachi CP-D10 Series Bedienungsanleitung

Hitachi

Hitachi CP-S420WA Bedienungsanleitung

Hitachi

Hitachi CPX870D Bedienungsanleitung

Hitachi

Hitachi CP-X8150 Bedienungsanleitung

Hitachi

Hitachi CPX7 Bedienungsanleitung

Hitachi

Hitachi CP-DH300 Bedienungsanleitung

Hitachi

Hitachi ED-S3350 and Technisches Dokument

Hitachi

Hitachi CP-X1250J Bedienungsanleitung

Hitachi

Hitachi CPX305 - XGA LCD Projector Montage- und Wartungsanleitung

Hitachi

Hitachi CP-S235 Konfigurationshandbuch

Hitachi

Hitachi PJTX10WAU Bedienungsanleitung

Hitachi

Hitachi CP-WX11000 Bedienungsanleitung

Beliebte Projektor Handbücher anderer Marken

iEmmet

iEmmet MP-312 Bedienungsanleitung

Epson

Epson VS400 Bedienungsanleitung

Sony

Sony VPL-HS10 Marketing Specifications & Features Bedienungsanleitung

Sony

Sony VPL-HW65ES Service-Handbuch

Toshiba

Toshiba TLP-791U Bedienungsanleitung

Philips

Philips LC1341 Referenzhandbuch

Panasonic

Panasonic PTL735NTU - LCD PROJECTOR-NETWORK IB Bedienungsanleitung

NEC

NEC NP600S EDU Bedienungsanleitung

BenQ

BenQ SH753P Bedienungsanleitung

Eiki

Eiki EK-623U series Bedienungsanleitung

Epson

Epson PowerLite Pro Cinema 6020UB Bedienungsanleitung

Epson

Epson PowerLite Home Cinema 705HD Bedienungsanleitung

Christie

Christie LHD700 Bedienungsanleitung

Navitar

Navitar FX Bedienungsanleitung

InFocus

InFocus LitePro 560 Bedienungsanleitung

Sony

Sony SRX-R815P Bedienungsanleitung

Vivitar

Vivitar DP1500 X Bedienungsanleitung

Acer

Acer C20 Series Bedienungsanleitung