Hobie Pasific Bedienungsanleitung
1
ASSEMBLY MANUAL
Last up-date : December 2003
2
List of parts....................................................................3
Hull assembly................................................................6
Trampoline ....................................................................7
Rudder installation.........................................................9
Mast set up..................................................................10
Spreader bars..............................................................11
Preparation for mast raising........................................12
Stepping the mast .......................................................13
Trapeze assembly.......................................................14
Mainsail.......................................................................15
Cunningham/Righting line...........................................16
Jib sail .........................................................................17
Jib sheet system..........................................................18
Mainsheet system .......................................................19
Spinnaker Kit...............................................................21
Caution & safety tips ...................................................24
TABLE OF CONTENT
3
Tools necessary :
⇒ 2 wrenches - No. 17
⇒ 2 wrenches - No. 10
⇒ 1 pair of universal pliers
It is advisable to have at least 2 people to assemble
the Hobie Pacific .
LIST OF PARTS
Hulls (2)
Front crossbar
Rear crossbar
Mast
Trampoline assembly
Rear trampoline strip
Rudder assemblies (2)
LIST OF PARTS
CAUTION - DANGER
ALUMINIUM MAST - STAY AWAY OF
ELECTRICAL WIRES
Tiller crossbar
Tiller extension
Mainsail + battens (7)
Jib sail
Wires bag
Ropes bag
Parts bag
4
WIRES :
1. Shrouds with adjuster covers
2. Jib halyard + forestay + pigtail
3. Diamond wire assembly
4. Trapeze wires (4)
5. Bridles (2)
6. Trapeze handles (J & H) (4)
Rope locks (4)
Trapeze shock cords (2)
LIST OF PARTS
ROPES :
All ropes are labelled with ref.
number and name. Please
check carefully before using.
1. Righting line
2. Mainsheet
3. Jib sheet
4. Main halyard
5. Jib halyard
6. Jib luff tensioner line
7. Cunningham line
8. Trapeze adjustment line
1 2 3 4
5 6 7 8
1 2 3
4 5
6
5
LIST OF PARTS
Parts Bag
1. Spreader bar assembly (2)
2. Mainsheet top block with hook
3. Mainsheet ratchet block
4. Jib furler
5. Cunningham block with hook
6. Rudder Pins (2)
Nylon Washers (4)
Ring clips (4)
7. Jib clew blocks (2) with clew shackle
8. Plastic ball stops (2) for cunningham line
9. Tiller connector kits - TCM (2)
10. Drain plugs (2)
11. Stay adjusters (2)
12. toggles (2)
clevis pins (6)
split rings (6)
13. Shackles : 8 mm (1)
6 mm (4)
4 mm (1)
14. Tube silicone sealant
15. Cunningham cleats
1
2
3
4
5
6
10
9
8
7
11
12
13 15
14
6
Hull assembly
Position the hulls in parallel with the inner
sides facing the ground.
NB: It is advisable to put some padding under the
hulls to prevent scratching and damage.
Lift the right hull. One person straddles the hull to
hold it in an upright position. The other person
applies the Silicone sealant (for waterproofing)
around the bolt holes in the deck saddles.
1
Take the front crossbar and remove the 2 nuts
(one stainless washer and one nylon washer
from each bolt). NB: Ensure that the
trampoline track faces the rear of the boat. NB: it is
advisable to place a small amount of grease on each
bolt.
2
Position the front crossbar in
the deck saddle and push the
bolts into the holes. Reach in
through the inspection port and
position the nylon washer, the
stainless washer and then one nut on
the thread of each bolt. Tighten the
nuts by hand or loosely with the #17
wrench - Do not overtighten at this
stage.
3
Lift the port hull, and repeat the mounting process.
Install the rear crossbar now in the same manner as the front crossbar.
Now using the # 17 wrench tighten all 8 bolts and nuts securely, then install the lock nuts.
NB : Check all nuts after your first sailing and afterwards on a regular basis
4
7
Trampoline Assembly
Take one of the side tensioning lines and pass the line
through the pad-eye that is fixed to the front crossbar.
Then tie with a bowline knot the line onto the grommet of
the trampoline near where the rope exits the trampoline.
Repeat this step at the opposite side front corner.
Unfold the trampoline. Note that the trampoline has side tension lines that are already pre-threaded.
Insert the front edge of the trampoline into the track at the left, rear side of the front crossbar. Continue
feeding the trampoline into the track and position it in the center. line up the grommet in the center of the
trampoline with the dolphin striker post to ensure it is centered.
1
2
Move to the rear of the trampoline. Very closely to where the side
tensioning line exits the rear of the trampoline tie a loop. ensure you
pull the side tensioning line firmly as to tie the loop as closely to the
trampoline where the rope exits as possible. Tie a bowline or a similar
loop in the line which will be used for a 4:1 purchase of the side
tensioning lines. Repeat this step for the opposite side rear corner.
Now take the tale of the side
tensioning line and pass the
rope through the pad-eye
mounted on the rear cross beam
closest to where the line exits
the trampoline. Then pass the
line back through the loop tied in
step3. Again go through the
pad-eye on the beam and back
through the loop. This will
provide a 4:1 purchase. Pull the
line slightly as to take some tension for
the sides but do not completely tension
at this stage. Repeat this step for the
opposite side rear corner. Ensure that
the trampoline is still centered.
3
4
8
Trampoline
Again, take the side tensioning line and very
firmly pull the line. Once as tight as possible tie
off the line with an adequate knot. Repeat this
for the opposite side rear corner.
7
NB : It is important that the trampoline be strongly tightened.
Check the tension on a regular basis.
Find the trampoline rod and insert it
into the rear of the trampoline.
Commence lacing the rear of the
trampoline. The lacing line starts at the
left, rear lacing button on the rear
crossbar. Lace the rear of the
trampoline as tightly as possible as per
the photographs and diagrams
supplied. Continue across the rear
crossbar and tie off securely when
Début
5
6
Now, once the side tension line has been tied
off, using the long tail, pass it back through the
grommet at the rear corner of the trampoline
near where the side tensioning line exits the
trampoline. Then pass the line through the
pad-eye on the rear crossbar. Again pass the
tail through the grommet on the trampoline and
pull the line firmly. Once the sides of the
trampoline have been further tightened, tie off the line and hide the tail under
the trampoline. Repeat this step for the opposite side rear corner.
8
9
Rudder installation
Identify the left hand end of the tiller crossbar. Fasten it to the tiller
connector at the front of the left rudder arm using the tiller connector kit.
Install as per photo. Repeat above procedure for the right side.
NB: Rudder toe in - toe out can be adjusted with the tiller crossbar adjuster. 3 - 5
mm toe is advised.
2
Connect the tiller extension to the pin located
in the centre of the tiller crossbar using the
clevis pin and ring clip supplied.
3
Identify the rudder assemblies (green
sticker on tiller arm = starboard ; red
sticker on tiller arm = port)
Take the port rudder, place the 2 Nylon washers
in position, align the holes in the lower rudder
casting with the holes in the gudgeon, and insert
the rudder pin. Fit the 2 split rings.
NB: confirm that you have installed the port
rudder on the port hull.
Repeat the procedure for the starboard rudder and hull.
1
10
Mast set up
Place the mast onto two supports (eg: two
pieces of polystyrene).
Unroll the trapeze wires and fix them using a
shackle to the upper hole on the mast tang (two on
each side).
1
Unroll the shrouds and the forestay wire (with
the jib halyard block) and fix them to the lower
hole of the mast tang using a shackle.
The shrouds go onto each side of the forestay.
2
Trapeze wires
Trapeze wires
Shrouds
Forestay
IMPORTANT : Attach the jib halyard rope to
the small single block at the end of the jib
halyard wire.
Attach the main halyard rope to the thimble on the
end of the main halyard wire.
NB: Secure both wire and rope halyards at the base
of the mast. Ensure that the 2 shackles on the mast
tang are tightened with pliers or shackle key.
3
Inhaltsverzeichnis
Andere Hobie Spielzeug Handbücher
