Honeywell Aquastat L7224U Bedienungsanleitung

TECHNICIAN’S QUICK REFERENCE GUIDE

69-1957—1

L7224 Series

Oil Electronic

Aquastat® Controller

The following service procedure provides a quick overview for

L7224 Series Controllers. For more information, refer to form

69-1384.

On the L7224U the High Limit, High Limit Differential, Low Limit,

and Low Limit Differential can be adjusted to the settings

recommended by the boiler OEM.

Adjusting Settings

To discourage unauthorized changing of Aquastat® settings, a

procedure to enter the adjustment mode is required. To enter the

adjustment mode, press the UP, DOWN, and Ibuttons

simultaneously for three seconds. Press the I button until the

feature requiring adjustment is displayed:

• HL—High Limit.

• LL—Low Limit.

• Ldf—Low Limit differential.

• F - C—°F or °C.

Then press the UP and/or DOWN buttons to move the set point to

the desired value. After 60 seconds without any button inputs, the

control will automatically return to the READ mode.

To use the L7224U in a cold start boiler application, disable the

Low Limit function by pressing the UP arrow button, DOWN arrow

button and Ibuttons simultaneously for three seconds. Then push

the Ibutton until LL is displayed. Then press the down arrow

button until OFF is displayed.

Display

In the RUN mode, the Aquastat® will flash “bt” (boiler temp)

followed by the temperature (i.e., 220), followed by °F or °C.

To read boiler settings, press the Ikey to read the parameter of

interest. For example, press I(HL) High Limit is displayed,

followed by a three-digit number, i.e., 220, followed by °F or °C.

69-1957-1.fm Page 1 Tuesday, June 20, 2006 11:06 AM

CLICK ANYWHERE on THIS PAGE to RETURN

to HONEYWELL L7224U UNIVERSAL

AQUASTAT at InspectApedia.com

69-1957—1 2

L7224 SERIES

Pressing the I button again will display the LL (Low Limit) followed

by a three-digit number and the corresponding degree designator.

See the table below for an explanation of display readout.

After approximately 60 seconds without any key presses, the

display will enter a dim display mode. To return to the bright

display mode, simply press and release any key.

Table 1. LED Error Codes

Error Code Cause/Action

Err1 Sensor fault; check sensor.

Err2 ECOM fault; check EnviraCOM. wiring.

Err3 Hardware fault; replace control.

Err4 B1 fault; check B1 wiring/voltage.

Err5 Low Line; Check L1-L2, 110 Vac.

Err6 Fuse; Check ECOM wires, Replace fuse.

Err7 EEPROM, HL, LL, Hdf, Ldf, Reset to default values.

Err8 Repeated B1 fault (voltage present at B1 when

output is turned off); check B1 wiring/voltage.

Boiler Temperature

Text Description

Display

Shows

High LimitHL

Low LimitLL

High Limit DifferentialHdf

Low Limit DifferentialLdf

Local Thermostat Statustt

Enviracom Thermostat Statustte

Burner Statusbrn

Circulator Statuscir

Zone ControlZc

Zone RequestZr

Error Codeerr

Degrees Fahrenheit

Degrees Celsius

M22149

69-1957-1.fm Page 2 Tuesday, June 20, 2006 11:06 AM

3 69-1957—1

L7224 SERIES

Table 2. L7224 Controller Operating Sequence

Troubleshooting

When attempting to diagnose system performance, reference the

LED display to help identify specific areas not working properly.

The LED display will scroll “err”, followed by a digit (1-8). See

Table 1 for a description of the error and suggested actions. See

below for a troubleshooting guide.

Action System Response

Thermostat

calls for heat.

Circulator starts when water temperature is

above Low Limit setting (if applicable). Boiler

temperature is checked. Burner starts when

water temperature is below High Limit setting.

Boiler exceeds

the High Limit.

Burner is turned off. Burner restarts when the

water temperature drops below the High Limit

setting minus the differential.

Thermostat is

satisfied.

Circulator and burner turn off.

Error conditions

1-5.

If an error condition is detected, all outputs

except ZC are shut down. Burner is off. Control

continues to function and restarts when error is

corrected. During the error check sequence, the

system checks for drift in the sensor and

corrosion in the connections.

Error conditions

6-7.

If error condition 6 or 7 occurs, the control has

reset the High Limit, Low Limit and Differential

Setting to a default setting and will continue to

run at those settings. Performance of the system

will be degraded.

Error condition

If the error condition is detected, all outputs

except ZC are shut down. Burner is off. Control

continues to function and restarts when all three

user keys have been pressed longer than 60

seconds.

Table 3. Troubleshooting Guidea.

System

Condition

Diagnostic

Condition Check Action

Boiler is

cold,

house is

cold

Display is OFF 120 Vac system

power.

Turn system power on.

Display is ON;

TT-LED is OFF

24 Vac T-T No 24V; replace

control

Display is ON;

TT-LED is OFF

24V present;

disconnect

thermostat,

short T-T

Boiler starts, check

wiring and thermostat

a. Refer to Fig. 5 for Display and LED locations.

b. ZC LED ON indicates ZC terminal power is OFF.

c. ZC LED OFF indicates ZC terminal power is ON.

69-1957-1.fm Page 3 Tuesday, June 20, 2006 11:06 AM

Automation and Control Solutions

Honeywell International Inc. Honeywell Limited-Honeywell Limitée

1985 Douglas Drive North 35 Dynamic Drive

Golden Valley, MN 55422 Toronto, Ontario M1V 4Z9

customer.honeywell.com

® U.S. Registered Trademark

69-1957—1 Rev. 06-06

Boiler is

cold,

house is

cold

Display is ON;

TT-LED is ON

B1 LED is ON

120 Vac at B1-

•If no, replace control.

•If yes, check burner

and wiring

Display is ON;

TT-LED is ON

Refer to err on

display

—

Boiler is

hot, house

is cold

Display is ON;

TT-LED is ON

C1 LED is ON

120 Vac at C1-

•120 Vac at C1-C2,

check wiring to pump

•Wiring ok, is pump

running? If not,

replace the pump.

•If pump is running,

check for trapped air

or closed zone

valves.

Display is ON;

TT-LED is ON

C1 LED is OFF;

ZC LED is ONb

Boiler below the

Low Limit

temperature,

wait for boiler to

go above Low

Limit

temperature.

Display is ON;

TT-LED is ON

ZC LED is

OFFc

Boiler above

LL? If yes,

check for 120

Vac between ZC

and L2

•If no 120 Vac,

replace control.

•If yes, check zone

relays, circulators

and wiring.

Table 3. Troubleshooting Guidea.

System

Condition

Diagnostic

Condition Check Action

a. Refer to Fig. 5 for Display and LED locations.

b. ZC LED ON indicates ZC terminal power is OFF.

c. ZC LED OFF indicates ZC terminal power is ON.

69-1957-1.fm Page 4 Tuesday, June 20, 2006 11:06 AM

Andere Handbücher für Aquastat L7224U

Andere Honeywell Controller Handbücher

Honeywell

Honeywell Lyric Betriebsanleitung

Honeywell

Honeywell Touchpoint Plus Benutzerhandbuch

Honeywell

Honeywell Excel 10 Bedienungsanleitung

Honeywell

Honeywell UDC 6300 Leitfaden

Honeywell

Honeywell RA890G Bedienungsanleitung

Honeywell

Honeywell ICON 100 SERIES Bedienungsanleitung

Honeywell

Honeywell ML6174 Series Bedienungsanleitung

Honeywell

Honeywell UDC2500 Bedienungsanleitung

Honeywell

Honeywell ControlEdge 900 platform Technisches Handbuch

Honeywell

Honeywell ControLinks R7999A Bedienungsanleitung

Honeywell

Honeywell HCE 40 Programmierhandbuch

Honeywell

Honeywell Touchpoint Plus Versionshinweis

Honeywell

Honeywell R7426A Bedienungsanleitung

Honeywell

Honeywell UDC 2300 Bedienungsanleitung

Honeywell

Honeywell S9360B Bedienungsanleitung

Honeywell

Honeywell ML200 Series Bedienungsanleitung

Honeywell

Honeywell TheraPro HR90 Bedienungsanleitung

Honeywell

Honeywell Optiflex Montageanleitung

Honeywell

Honeywell SSW2-1M Bedienungsanleitung

Honeywell

Honeywell UMC800 Bedienungsanleitung

Honeywell

Honeywell L4188 Bedienungsanleitung

Honeywell

Honeywell ML6425B Bedienungsanleitung

Honeywell

Honeywell S9200U1000 Bedienungsanleitung

Honeywell

Honeywell Spyder 7 Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung

3M MicroTouch EX113 Bedienungsanleitung

KUHN

KUHN TKS Bedienungsanleitung

S&C

S&C PMH Bedienungs- und Wartungshandbuch