Honeywell HNDR-S 4848 Bedienungsanleitung

HONEYWELL SECURITY TECHNICAL BULLETIN 11 December 2008

www.asia.security.honeywell.com Rev 1.0 1 of 5

Honeywell Video Systems

Subject: Control HNDR-S 4848 DVR by VideoBlox HEGS5BLX

Introduction

This document describes the Protocol Interface Translator (PIT) operation specific to the Honeywell HNDR-S

series DVR. For further details on the PIT, please refer to the PIT User manual. For further details on the DVR,

please refer to the appropriate Honeywell HNDR-S DVR manual.

Quick Start Switch Settings

Output

Protocol S1/8 S1/7 S1/6 S1/5 S1/4 S1/3 S1/2 S1/1

Valid

Function Valid

Function

ASCII

string

mode

ASCII

string

mode

ASCII

string

mode

ASCII

string

mode

Off Off Off Off On On On On

Address S2/8 S2/7 S2/6 S2/5 S2/4 S2/3 S2/2 S2/1

Switch

Legend Address

7 Address

6 Address

5 Address

4 Address

3 Address

2 Address

1 Address

0 (B/cast) Off Off Off Off Off Off Off Off

Input

Protocol S3/8 S3/7 S3/6 S3/5 S3/4 S3/3 S3/2 S3/1

Slave Port

Baud

Slave

Port

Baud

Master

Port Baud Master

Port Baud Input

Type Input

Type

Bossware On Off On Off On On On Off

The above setting set the PIT as follows:

Receive Betatech compatible Bossware control messages on the RS422 slave port of the PIT at 19.2K baud.

The PIT unit address (S2/1 - S2/8 to OFF position) is set to broadcast, so all addresses will be translated. If

want to control specific unit of DVR, set the dip switch S2/1 – S2/8 of PIT address and add PIT per DVR. (It is

tested the address from 1 to 128.)

Unit ID S2/8 S2/7 S2/6 S2/5 S2/4 S2/3 S2/2 S2/1

1 Off Off Off Off Off Off Off On

2 Off Off Off Off Off Off On Off

3 Off Off Off Off Off Off On On

4 Off Off Off Off Off On Off Off

5 Off Off Off Off Off On Off On

255 On On On On On On On On

Transmit Honeywell HNDR-S control messages on the RS422 master port at 9600 baud, 8, N, 1 .

Note: To control HNDR-S series DVR, the DVR firmware should be 1.0.17 or later.

(Tested firmware: HVBCPUX – 4.96x HVBCFG – 3.08 (Build 32) HVBPIT44 – 3.03)

HONEYWELL SECURITY TECHNICAL BULLETIN 11 December 2008

www.asia.security.honeywell.com Rev 1.0 2 of 5

Hardware Configuration

•Connect CPU RS422 Master Port to Slave Port of HVBPIT44.

•Connect Master Port of HVBPIT44 to HNDR-S Com 2 (RS-485).

Pin Number CPU RS422 Master Port

(DB9 Female) HVBPIT44 Slave Port

(DB9 Female)

1 Tx- Rx-

2 Tx+ Rx+

3 Rx+ Tx+

4 Rx- Tx-

5 Signal Gnd Signal Gnd

6 +12V source +12V input

7 NC NC

8 NC NC

9 Ground Ground

Pin Number HVBPIT44 Master Port

(DB9 Female) HRHD-S Com 2

1 Tx- Tx

2 Tx+ Rx

HONEYWELL SECURITY TECHNICAL BULLETIN 11 December 2008

www.asia.security.honeywell.com Rev 1.0 3 of 5

Device Configuration

Go to Control page to configure external CCTV peripherals which may be controlled by VideoBloX keyboard.

1. Copy the HNDR-S.db and HNDR-S.mb files to root directory “C:\Program

Files\Honeywell\VBloXCFG\DBF\”

2. Execute the VbloxCFG software and go to “Control” page.

3. Select the “Device Type” which is to be configured.

4. Click icon to browse “HNDR-S.db” which is locate in “C:\Program Files\Honeywell\VBloXCFG\DBF\”

5. Set “Com Port” to “1” if the control signal to the device is connected to the VideoBloX CPU master

communications port.

6. Set the “Control Type” to the type of interface used to control the external device.

7. Set “Switch Offset” to “-1” if no automatic video switch operation is required when the device is selected.

The offset will be added to the selected device number and the resulting value will be used as the matrix

video input channel which will be selected. e.g. Switch Offset =29, the first channel of HNDR-S DVR is

input 30.

8. Click “Download” button to download after changed.

HONEYWELL SECURITY TECHNICAL BULLETIN 11 December 2008

www.asia.security.honeywell.com Rev 1.0 4 of 5

HNDR-S 4848 DVR Configuration

1. Configure Communication port

a. Push Menu button of DVR and enter the DVR setting menu.

b. Move to System menu and select Serial Setup.

c. Move to COM2 485 and select Keyboard HTX-3000 as below figure.

2. Configure Keyboard Control Address and Keyboard PTZ address as below figure.

a. Push Menu button of DVR and enter the DVR setting menu.

b. Move to Miscellaneous menu.

c. Select Keyboard Control Address to 1.

HONEYWELL SECURITY TECHNICAL BULLETIN 11 December 2008

www.asia.security.honeywell.com Rev 1.0 5 of 5

HEGS5BLX Operation

To select “HNDR-S 4848”, press “DVR” button. Then press “1” + “Enter” buttons to select DVR number 1.

A B C D E F G H

KJIML

Joystick

DVR Function Keys

Item Function supported

by Keyboard Description

(The Keyboard should be in DVR mode for the below operation)

1 Menu Press “H”

2 Play Press “B”

3 Rewind Press “G”

4 Forward AUX Mode LED on, Press “C”

5 Search Press “C”

6 Sequence Press “F”

7 Select AUX Mode LED on, Press “E”

8 Multi-screen AUX Mode LED on, Press “F”

9 Exit AUX Mode LED on, Press “G”

10 Enter AUX Mode LED on, Press “H”

11 Up Hold down “ALT” + “Up”

12 Down Hold down “ALT” + “Down”

13 Left Hold down “ALT” + “Left”

14 Right Hold down “ALT” + Right”

I: Use to move between menu items

J: Select DVR channel depending on the position

K: Select DVR channel depending on the position

L: Select DVR channel depending on the position

15 DVR channel select

M: Use to move between menu items

* Detail DVR operation procedure, please refer to the DVR manual.

Note: The information contained herein is subject to change without notice.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Honeywell DVR Handbücher

Honeywell

Honeywell 35 Series Bedienungsanleitung

Honeywell

Honeywell HREP24 Bedienungsanleitung

Honeywell

Honeywell hus-nvr-1032-e Bedienungsanleitung

Honeywell

Honeywell Rapid Eye Service-Handbuch

Honeywell

Honeywell CADVR-1004-WD-M Bedienungsanleitung

Honeywell

Honeywell HRDE4X4 Bedienungsanleitung

Honeywell

Honeywell HRDVS Bedienungsanleitung

Honeywell

Honeywell HRHD 410 Bedienungsanleitung

Honeywell

Honeywell HRTL-One Bedienungsanleitung

Honeywell

Honeywell HRSD8 Bedienungsanleitung

Honeywell

Honeywell HRXD Series Bedienungsanleitung

Honeywell

Honeywell HTR62 Installationsanleitung

Honeywell

Honeywell Fusion IV Bedienungsanleitung

Honeywell

Honeywell MAXPRO NVR Series Bedienungsanleitung

Honeywell

Honeywell HREP 8 Bedienungsanleitung

Honeywell

Honeywell MAXPRO NVR Hybrid XE Bedienerhandbuch

Honeywell

Honeywell HRXD Bedienungsanleitung

Honeywell

Honeywell HRDP DVR Bedienungsanleitung

Honeywell

Honeywell HREP24 Bedienungsanleitung

Honeywell

Honeywell HRGX45 Bedienungsanleitung

Honeywell

Honeywell VPR100 Bedienungsanleitung

Honeywell

Honeywell VRX180 Bedienungsanleitung

Honeywell

Honeywell HRDE4X4 Bedienungsanleitung

Honeywell

Honeywell HD-DVR-1004 Bedienungsanleitung

Beliebte DVR Handbücher anderer Marken

FLIR

FLIR M3100E Series Bedienungsanleitung

VTRACKPRO

VTRACKPRO FPRO300 Bedienungsanleitung

Swann

Swann NVR-7085 models Bedienungsanleitung

XtendLan

XtendLan DVR-1670C Bedienungsanleitung

urmet domus

urmet domus 1093/004AHD Bedienungsanleitung

Holux

Holux M1 Bedienungsanleitung

CMOS DOTCOM

CMOS DOTCOM ANX-1670 Bedienungsanleitung

Whistler

Whistler D16VRS Bedienungsanleitung

Defender Security

Defender Security 82-20235 Bedienungsanleitung

MISUMI

MISUMI MP-WF100M Bedienungsanleitung

Speco

Speco D8HU Bedienungsanleitung

UST

UST DDR-E04AA Gebrauchsanweisung

Consolidated

Consolidated Digital Video Recorder Bedienungsanleitung

Mace

Mace DVR0404RW Kurzanleitung

RCA

RCA RTD315W Bedienungsanleitung

Hauppauge

Hauppauge HD PVR 2 Bedienungsanleitung

Identivision

Identivision ICR-PH161i PIONEER Bedienungsanleitung

DIGIFUSION

DIGIFUSION FVRT150 Bedienungsanleitung