Honeywell Smart IO Bedienungsanleitung

MOUNTING INSTRUCTIONS

Smart IO

IO-10MIXR-WE/IO-10MIXR-NWE

SUPPORTED DOCUMENTS

• 31-00427 (Smart IO Datasheet)

• 31-00429 (Smart IO Installation Instructions)

EKeep these instructions together with the

device or with the equipment

documentation! Only qualified personnel

may perform electrical connections for 230

VAC.

FCette instruction est à conserver avec le

contrôleur ou avec la documentation de

l'installation ! Le raccordement électrique

pour le 230 VAC ne peut être effectué

que par le personnel autorisé.

PGuarde estas instruςões junto do regulador

ou junto da documentaςão da instalaςão! A

ligaςão eléctrica a 230 VAC só deve ser

efectuada por pessoal especializado.

DDiese Anleitung ist beim Gerät oder in der

Anlagendokumentation aufzubewahren!

Elektrisches Anschließen von 230 VAC ist

nur durch autorisiertes Fachpersonal

gestattet.

IQueste istruzioni devono essere

conservate insieme al lettore o con la

documentazione dell´impianto! I

collegamenti a 230VCA devono essere

eseguiti da personale qualificato.

SDenna instruktion skall förvaras tillsammans

med regler eller

anläggningsdokumentationen! Elektrisk

anslutning med 230 VAC får endast utföras

av behörig personal.

DK Opbevar denne vejledning sammen med

regler eller med anlægsdokumentationen!

Elektrisk tilslutning for 230 VAC bør kun

foretages af autoriserede personer.

NDenne veiledningen skal oppbevares

sammen med regler eller

anleggsdokumentasjonen! Elektrisk

tilkopling med 230 VAC må kun utføres

av fagfolk.

FI Tätä ohjetta tulee säilyttää laitteen

läheisyydessä tai yhdessä muiden

dokumenttien kanssa! Vain asianmukaiset

oikeudet omaava henkilö saa suorittaa 230

VAC käyttöjännitteen liitäntätöitä.

ES Conserve estas instrucciones con el recalar

o con la documentación de la instalación.

La conexión eléctrica a 230 VCA debe

hacerse solamente por personal

qualificado.

NL Deze handleiding moet bij de regelaar, of

met de documentatie van de installatie

worden bewaard! De elektrische

aansluiting voor 230 VAC mag alleen door

geautoriseerd personeel worden

uitgevoerd.

PL Instrukcję obsługi należy przechowywać

przy urządzeniu albo w dokumentacji

technicznej. Tylko autoryzowany servis jest

upoważniony do podłączenia do 230 VAT.

SC 请将此装配说明书与设备或者与设备的其

他文档保存在一起！ 230 V 交流电的接线

操作仅允许由合格的专业人员执行

TC 請將此裝配說明書與設備或者與設備的

其他文件儲存在一起！

僅能由合格的專業人員進行230 V交流

電的接線作業。

K본 설치 설명서를 해당 장치 또는 관련

문서와 함께 보관하시기 바랍니다.

230VAC 전원 연결은 관련 작업 전문가에

의해 수행되어야 합니다.

SMART IO

31-00428 | Rev.10-20

Part Number: 32350802-001 2

WARNING

Electrical Shock Hazard.

Can cause severe injury, death or property

damage.

Disconnect the power supply before beginning

installation to prevent electrical shock and

equipment damage. More than one power supply

may have to be disconnected.

When Installing This Product

1. Read these instructions carefully. Failure to follow

them could damage the product or cause a hazard-

ous condition.

2. Check the ratings given in the instructions and

marked on the product to make sure the product is

suitable for your application.

3. Installer must be a trained, experienced service tech-

nician.

4. After installation is complete, check the product

operation.

5. Be sure wiring complies with all applicable codes,

ordinances and regulations.

This symbol on our product shows a crossed-out “wheelie-

bin” as required by law regarding the Waste of

Electrical and Electronic Equipment (WEEE) disposal. This

indicates your responsibility to contribute in saving

the environment by proper disposal of this Waste i.e. Do not

dispose of this product with your other wastes. To

know the right disposal mechanism please check the

applicable law.

Regulation (EC) No 1907/2006

According to Article 33 of REACH Regulation, be informed

that this product may contain components with lead (CAS:

7439-92-1) content above the threshold level of 0.1% by

weight.

INTRODUCTION

This document contains mounting instructions for the

Smart IO including the accessories.

Mounting the Smart IO on DIN Rail

The Smart IO can be mounted on the vertical or horizontal

DIN rail. The following procedure applies to both mounting

conditions.

1. Remove the top and bottom terminal covers from

Smart IO using fingers by pushing terminal covers

upwards as shown in the below figure.

2. Extend both red clips to the DIN Rail Release posi-

tion as shown in the below figure.

3. Mount the Smart IO onto the DIN rail and push both

red clips in to secure it in place.

4. Connect the antenna, terminal wires, and Ethernet

cables. See the “Antenna” section on page 3 for

antenna installation. See the Smart IO Installation

guide (31-00429) for wiring connections.

5. Remount the Terminal covers.

WEEE

WEEE Directive 2012/19/EC Waste

Electrical and Electronic Equipment

Directive

• At the end of the product life,

dispose of the packaging and

product in an appropriate recycling

center.

• Do not dispose of the device with

the usual domestic refuse.

• Do not burn the device.

Terminal Cove

(Bottom side)

Terminal Cover

(Top side)

Red clip

Wall Mount

DIN Rail Release

DIN Rail Lock

Smart IO

DIN Rail

Red Clip

Local Antenna

SMART IO

3 31-00428 | Rev.10-20

Part Number: 32350802-001

Mounting the Smart IO on a

Wall/Panel Using Screws

1. Remove the top and bottom terminal covers from

Smart IO using fingers by pushing terminal covers

upwards as shown in the below figure.

2. Extend both red clips to the Wall Mount position as

shown in the below figure.

3. Hold the Smart IO along the wall and mark the drill-

ing locations through the red clip slots as shown in

the below figure.

4. Remove the Smart IO from the wall and drill two holes

at the marked locations.

5. Insert anchors (if applicable) into the two mounting

screw holes.

6. Hold the Smart IO along the wall/panel so that the

holes are aligned.

7. Insert the screw into the topside hole first and fasten

with a screwdriver.

NOTE: It is recommended to use the 6-18 1” pan head

Phillips tapping screws.

8. Insert the screw into the bottom hole and fasten with

a screwdriver.

9. Connect the antenna, terminal wires, and Ethernet

cables. See the “Antenna” section on page 3 for

antenna installation. See the Smart IO Installation

guide (31-00429) for wiring connections.

10. Remount the Terminal covers.

Antenna

Smart IO has a local antenna included in the kit. The

antenna is to facilitate wireless communication via Wi-Fi

and Bluetooth with other devices. If the Smart IO is

mounted inside a cabinet/enclosure and you are using the

Local antenna, use an enclosure that is made of a non-

metallic material to achieve a reliable wireless signal.

Replace the local antenna with the Remote antenna when

an extended range is needed or when the IO module is

mounted in a metal cabinet/enclosure. The Remote

antenna has a cable that connects to the Smart IO, and the

antenna is mounted outside the cabinet/closure. When the

Smart IO is mounted inside a metal cabinet/enclosure, the

Remote Antenna is required to achieve a reliable wireless

signal.

Installing the Local Antenna

1. Remove the terminal blocks on either side of the SMA

Connector for easier access to the connector.

2. Insert local antenna terminal nut into the SMA con-

nector.

3. Tighten by turning the base of the antenna clockwise.

Terminal Cover

(Bottom side)

Terminal Cover

(Top side)

Red clip

Wall Mount

DIN Rail Release

DIN Rail Lock

Screw

Panel/Wall

Smart IO

Anchor

Local Antenna

SMA Connector

Local Antenna

Smart IO

SMART IO

31-00428 | Rev.10-20

Part Number: 32350802-001 4

Installing the Remote Antenna

1. Uninstall the Local antenna by turning the base of

the antenna counter-clockwise.

2. Place the Remote antenna where the signal reception

is good.

3. Safely route the Remote antenna wire terminal nut to

the Smart IO.

4. Remove the terminal blocks on either side of the SMA

Connector for easier access to the connector.

5. Insert the wire terminal nut into the SMA connector.

6. Tighten the wire terminal nut by turning the nut

clockwise. Do not overtighten.

7. Remount the terminal blocks.

NOTE: Ferrite ring is not required when the Remote

Antenna is used with the Smart IO.

REMOTE ANTENNA PLACEMENT

• Place and align the antenna in a way that the Wi-Fi

signal does not interfere with many obstacles.

• Obstacles such as metal, steel-reinforced concrete wall

filter ~10-90% of the Wi-Fi signal. Other obstacles such

as drywall, wood, glass filter ~0-10% of the Wi-Fi signal.

• The antenna has a strong signal transmission/reception

from the side. See figure below. Position the sides of the

antenna towards the device it is communicating with

(e.g Gateway/WiFi Node).

• Keep the antenna away from devices that cause wireless

interference such as other Wi-Fi network and

telecommunications equipment.

• Make sure that the antenna is installed perpendicular to

the surface for a good Wi-Fi signal.

• Do not install the antenna close to the floor.

• The Local antenna can be used when the Smart IO is

installed in a plastic cabinet/enclosure.

Removing the Smart IO from the

DIN Rail

1. Remove the Terminal Covers if applicable.

2. Disconnect all the communication and power supply

terminals from the Smart IO.

3. Hold the Smart IO with one hand and insert a flat

blade screwdriver into the bottom red clip slot and

pull the red clip outward to release the Smart IO from

the DIN rail.

4. Repeat the same for the top red clip.

5. Remove the Smart IO from the DIN rail.

Removing the Smart IO from the

Wall/Panel

1. Remove the Terminal covers if applicable.

2. Disconnect all the communication and power supply

terminals from the Smart IO.

3. If the remote antenna is installed, remove the termi-

nal blocks on either side of the SMA Connector for

easier access to the connector. Disconnect the

antenna by turning the antenna wire terminal nut

counter-clockwise.

4. Use a screwdriver to remove the bottom screw first.

5. Hold the Smart IO with one hand and remove the top

screw.

6. Remove the Smart IO from the wall/panel.

SMA Connector

Remote Antenna

Wire Terminal Nut

Smart IO

Gateway/Wi-Fi Node

Surface

Flat Blade Screwdriver

SMART IO

® U.S. Registered Trademark

31-00428 | Rev.10-20

Part Number: 32350802-001

Honeywell Building Solutions

Honeywell

715 Peachtree Street NE

Atlanta, GA 30308

customer.honeywell.com

buildingcontrols.honeywell.com

DIMENSIONS

122 mm

(4.80”)

57.5 mm

(2.26”)

130.7 mm

(5.15”)

105 mm

(4.13”)

45 mm

(1.77”)

110 mm

(4.33”)

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Honeywell E/A-System Handbücher

Honeywell

Honeywell XIO-8AI Bedienungsanleitung

Honeywell

Honeywell Notifier NRX-M711 Bedienungsanleitung

Honeywell

Honeywell Excel 5000 open XFL521B Bedienungsanleitung

Honeywell

Honeywell ALERTON ACM-VLX Betriebsanleitung

Honeywell

Honeywell W7622D Bedienungsanleitung

Honeywell

Honeywell T2 Bedienungsanleitung

Honeywell

Honeywell PRO-2200 Bedienungsanleitung

Honeywell

Honeywell 2MLF-AV8A Bedienungsanleitung

Honeywell

Honeywell PRO4200 Bedienungsanleitung

Honeywell

Honeywell W7761A Bedienungsanleitung

Honeywell

Honeywell PEHA PHC 940/24 EM RU Bedienungsanleitung

Honeywell

Honeywell Sylk SI06042 Bedienungsanleitung

Honeywell

Honeywell XIO-10HUB Bedienungsanleitung

Honeywell

Honeywell PW6K1IN Bedienungsanleitung

Honeywell

Honeywell PEHA 940/24 EM RÜ o.T. Bedienungsanleitung

Honeywell

Honeywell Excel 5000 System Series Bedienungsanleitung

Honeywell

Honeywell Excel 5000 open XFL521B Bedienungsanleitung

Honeywell

Honeywell Pro-Watch 7000 Bedienungsanleitung

Honeywell

Honeywell 2MLF-DV4S Bedienungsanleitung

Honeywell

Honeywell PEHA PHC 940/16 AM Bedienungsanleitung

Honeywell

Honeywell GENT VIG-LPC-EN Benutzerhandbuch

Honeywell

Honeywell NOTIFIER FMM-4-20 Bedienungsanleitung

Honeywell

Honeywell Series 8 I/O Bedienungsanleitung

Honeywell

Honeywell TC4S Bedienungsanleitung

Beliebte E/A-System Handbücher anderer Marken

WAGO

WAGO 750-344 Bedienungsanleitung

Teknim

Teknim TWM-1887 Bedienungsanleitung

Intelligent Appliance

Intelligent Appliance IA-2662-E Bedienungsanleitung

BERGHOF

BERGHOF ECC DIO 16/16 Bedienungsanleitung

Advantech

Advantech PCM-27J3AU Installations- und Betriebshandbuch

Festo

Festo CP-E08-M12-CL Bedienungsanleitung

Measurement Computing

Measurement Computing PCI-DAS64/M1/16 Bedienungsanleitung

Hitachi

Hitachi HX-RIO3 Series Bedienungsanleitung

NUUO

NUUO SCB-A08 Bedienungsanleitung

M-system

M-system R3Y-RS8 Bedienungsanleitung

jablotron

jablotron JB-110N Bedienungsanleitung

Omron

Omron SYSMAC C200H Bedienungsanleitung

DOLD

DOLD SAFEMASTER M Bedienungsanleitung

ABB

ABB OPT-MF-001 Bedienungsanleitung

Omron

Omron SYSMAC C2000H Bedienungsanleitung

Helmholz

Helmholz TB20 Bedienungsanleitung

ICP DAS USA

ICP DAS USA tM-AD2 Bedienungsanleitung

Automationdirect.com

Automationdirect.com DL305 Bedienungsanleitung