Honeywell W7622D Bedienungsanleitung

W7622D

Triac Output Board

GENERAL

The W7622D Triac Output Board (“Triac Board”) is a Type F,

four-output accessory board that increases DeltaNet

MicroCel™ Controller (“M-CEL”) output from four to eight

using triacs as spst switches. Each M-CEL can use only one

output board. If an M-CEL has an output board, the Triac

Board can replace it.

Outputs can be used for standard on/off control. In sets of

two, they can be used to modulate Series 60 (floating) control

with on-time resolution as low as 10 ms.

Specifications:

Outputs Four isolated triac (spst)

Maximum voltage 30V ac

Maximum current 0.5A steady, 4.0A surge

Minimum current 50 mA

Latching current 20 mA

Holding current 5 mA

Isolation Each triac is isolated and can

be powered from separate or

common 24V ac or dc sources.

M-CEL models R7515A3030, R7515B3004,

and R7516B3011 (Triac

Boards can only be mounted in

M-CELs that have a large

enclosure [7.9 in. long X 6.6 in.

wide X 4.95 in. deep, 201 X

167.6 X 125.8 mm])

INSTALLATION

NOTE: All wiring must conform to applicable local codes,

ordinances, and regulations.

 Remove power from M-CEL. Remove metal cover.

CAUTION

If power is connected via screw terminals, you

MUST remove power

at its source

rather than

removing each wire individually. Removing

individual wires can cause damage.

INSTALLATION INSTRUCTIONS

 If an existing output board is in place, remove

the board:

a. Remove the two self-tapping screws and metal

standoffs that secure the board to the bracket.

b. Using a pair of needle nose pliers, compress

the tab of the white plastic standoff (located near

the center of the board) and, at the same time,

carefully rotate the board away from the screw

terminal bracket to free the 10-pin connector

located on the back of the board near its

bottom edge.

 Starting with the Triac Board at an angle, align the

bottom part of the 10-pin connector to the 10 holes in

the bottom of the Triac Board. Rotate the Triac Board

toward the main bracket and allow the plastic standoff

to secure and center the board.

 Using the two long self-tapping screws, as well as the

two metal standoffs, secure the Triac Board to the

terminal strip bracket.

 Attach the new wiring label over the existing label on

the bracket.

 Wire to the outputs with 18 AWG (0.8012 sq mm) wire.

See job drawings for specific wiring. See Wiring

Diagram (this sheet) for terminal locations.

 After ensuring that there are no metal or wire scraps in

the M-CEL case, reconnect power and resecure cover.

95-7454

W7622D TRIAC OUTPUT BOARD

1 2 3 5 6 7 8 9 10 11 12 13 144

R1 D1 +10 V1 R2 D2 +10 V2

VOLT

DIGRTDVOLTDIGRTD

A B

19 20

C-NAP

15 17 18

WALL

MOD T2 T1

36 37 38 40 4139

1 2 3 4

4342

24 VAC

27 28 29 30 31 32 33 34

TR-5 TR-6 TR-7 TR-8

Outputs

Inputs

FOR WIRING DIAGRAM & RATINGS SEE MANUAL 63-4142 OR 77-0156

TRIAC

Output

USE COPPER

CONDUCTORS

ONLY

Strip

Length

COM

1-2 COM

3-4

FOR

TYPE F

BOARD

ONLY

97-9162 REV

NEC

CLASS 2

C7750

Wiring Diagram.

Home and Building Control Home and Building Control

Honeywell Inc. Honeywell Limited-Honeywell Limitée

Honeywell Plaza 155 Gordon Baker Road

P.O. Box 524 North York, Ontario

Minneapolis, MN 55408-0524 M2H 2C9

95-7454 5-91 Printed in U.S.A.

By using this Honeywell literature, you agree that Honeywell will have no liability for any damages arising out of your use

or modification to, the literature. You will defend and indemnify Honeywell, its affiliates and subsidiaries, from and against

any liability, cost, or damages, including attorneys’ fees, arising out of, or resulting from, any modification to the literature

by you.

Andere Honeywell E/A-System Handbücher

Honeywell

Honeywell ALERTON ACM-VLX Betriebsanleitung

Honeywell

Honeywell Notifier M710E Bedienungsanleitung

Honeywell

Honeywell PW6K1OUT Bedienungsanleitung

Honeywell

Honeywell Pro-Watch 7000 Bedienungsanleitung

Honeywell

Honeywell SLATE R8001U3001 Bedienungsanleitung

Honeywell

Honeywell Excel 5000 System Series Bedienungsanleitung

Honeywell

Honeywell Excel 5000 open XFL521B Bedienungsanleitung

Honeywell

Honeywell 2MLF-AV8A Bedienungsanleitung

Honeywell

Honeywell Multisite XIO Series Programmierhandbuch

Honeywell

Honeywell XIO-8AI Bedienungsanleitung

Honeywell

Honeywell PEHA PHC 940/16 AM Bedienungsanleitung

Honeywell

Honeywell PEHA 940/24 EM RÜ o.T. Bedienungsanleitung

Honeywell

Honeywell Smart IO Bedienungsanleitung

Honeywell

Honeywell TC4S Bedienungsanleitung

Honeywell

Honeywell Notifier NRX-M711 Bedienungsanleitung

Honeywell

Honeywell Series 8 I/O Bedienungsanleitung

Honeywell

Honeywell PW6K1IN Bedienungsanleitung

Honeywell

Honeywell Sylk SI06042 Bedienungsanleitung

Honeywell

Honeywell 2MLF-DV4S Bedienungsanleitung

Honeywell

Honeywell Excel 5000 open XFL521B Bedienungsanleitung

Honeywell

Honeywell AUDZBX75 Bedienungsanleitung

Honeywell

Honeywell PRO4200 Bedienungsanleitung

Honeywell

Honeywell PEHA PHC 940/24 EM RU Bedienungsanleitung

Honeywell

Honeywell Pro-Watch 7000 Bedienungsanleitung

Beliebte E/A-System Handbücher anderer Marken

WAGO

WAGO 750-344 Bedienungsanleitung

Teknim

Teknim TWM-1887 Bedienungsanleitung

Intelligent Appliance

Intelligent Appliance IA-2662-E Bedienungsanleitung

BERGHOF

BERGHOF ECC DIO 16/16 Bedienungsanleitung

Advantech

Advantech PCM-27J3AU Installations- und Betriebshandbuch

Festo

Festo CP-E08-M12-CL Bedienungsanleitung

Measurement Computing

Measurement Computing PCI-DAS64/M1/16 Bedienungsanleitung

Hitachi

Hitachi HX-RIO3 Series Bedienungsanleitung

NUUO

NUUO SCB-A08 Bedienungsanleitung

M-system

M-system R3Y-RS8 Bedienungsanleitung

jablotron

jablotron JB-110N Bedienungsanleitung

Omron

Omron SYSMAC C200H Bedienungsanleitung

DOLD

DOLD SAFEMASTER M Bedienungsanleitung

ABB

ABB OPT-MF-001 Bedienungsanleitung

Omron

Omron SYSMAC C2000H Bedienungsanleitung

Helmholz

Helmholz TB20 Bedienungsanleitung

ICP DAS USA

ICP DAS USA tM-AD2 Bedienungsanleitung

Automationdirect.com

Automationdirect.com DL305 Bedienungsanleitung