Honeywell E-Mon Class 3200 Bedienungsanleitung

62-0397-02

OWNER’S MANUAL

E-Mon Class 3200

Meter

ADVANCED KWH/DEMAND METER

62-0397_C.fm Page 1 Wednesday, May 9, 2018 9:28 AM

E-MON CLASS 3200 METER

62-0397—02 2

TABLE OF CONTENTS

Section 1.0 Introduction 3

Section 2.0 Internal Electronic Assemblies 5

Section 2.1 Main Power Board 5

Section 2.2 Display Board 6

Section 3.0 Meter Technical Specifications 7

Section 4.0 Safety Label Definitions and Information 10

Section 5.0 Precautionary and Safety Information 11

Section 6.0 Meter Installation 12

Section 6.1 Mounting the E-Mon Class 3200 Meter 12

Section 6.2 Main Power Board Connections 12

Section 6.3 Phasing of Line Voltage 16

Section 6.4 Current Sensor Installation & Wiring 17

Section 6.5 Main Power & Current Sensor Wiring Diagram 19

Section 6.6 Line Voltage/Current Sensor Diagnostics 20

Section 6.7 RS-485 Wiring 21

Section 6.8 RS-232 Communications 24

Section 6.9 Modem Wiring 26

Section 6.10 Modbus RTU Wiring 29

Section 6.11 BACnet MS/TP Wiring 30

Section 6.12 Connecting E-Mon Class 3200 Meters to USB Key using

RS485

Section 6.13 Ethernet Communications 31

Section 7.0 Multiple-Load Monitoring 32

Section 8.0 Preventative/Scheduled Maintenance 33

Section 9.0 Lithium Battery Replacement 34

Section 10.0 E-Mon Class 3200 Meter Operating Modes 36

Section 10.1 Start Up Screens 36

Section 10.2 Normal Mode Display Screens 37

Section 10.3 How to Program the Display Screens 38

Section 11.0 High Voltage Metering 43

Section 12.0 E-Mon Class 3200 Protocol Definitions 46

Section 13.0 Meter Limited Warranty 53

62-0397_C.fm Page 2 Wednesday, May 9, 2018 9:28 AM

E-MON CLASS 3200 METER

3 62-0397—02

1.0 INTRODUCTION

The Honeywell E-Mon Class 3200 meter is a 3-element meter with

communications. The device is used to monitor electric power usage of individual

loads after the utility meter and store kW and kVAR data for automatic meter

reading. Installation must only be performed by qualified personnel and in

accordance with these instructions and all applicable local and national electrical

codes. Honeywell E-Mon and its representatives assume no responsibility for

damages or injury resulting from the improper installation of this meter.

Verify the input voltage rating and configuration on the unit panel label to ensure

that it is suitable for the intended electrical service. For example, E-Mon Class

3200 meters labeled for 120/208V service MUST NOT be installed on service

feeds of 277/480 volts or 347/600 and vice versa.

Verify that the E-Mon Class 3200 meter’s current sensors are sized suitably for

the load to be monitored. Compare the color of the arrows on the current sensors

to the chart below to confirm the correct current sensor is being used.

Meter Labeled: Works On:

120V 120V, Single Phase

120/240V 120/240V, Single Phase

277V 277V, Single Phase

208V 208V, Three Phase

240V 240V, Three Phase

400V (380V,415V) 400V, Three Phase

480V 480V, Three Phase

600V 600V, Three Phase

Sensor Arrow Color Code Sensor Rating

Brown 100 A

Red 200 A

Yellow 400 A

Black 800 A

Blue 1600 A

White/Black 3200 A

62-0397_C.fm Page 3 Wednesday, May 9, 2018 9:28 AM

E-MON CLASS 3200 METER

62-0397—02 4

CAUTION

Internal circuit components are extremely sensitive to electrostatic

discharge. Prior to handling or touching internal circuitry, discharge

any static buildup on your person. To discharge yourself, touch a

grounded metal object such as conduit or an earth-grounded

enclosure.

WARNING

Use of this instrument, the E-Mon Class 3200 meter, in a manner

inconsistent with this manual or not specified by the manufacturer in

writing, can cause permanent damage to the unit and/or serious injury

to the operator. The protection and safety features provided by this

equipment may become impaired or otherwise compromised.

NOTE: If any trouble arises during the installation or functional verification

operations, do not immediately remove the unit. Before removing the

unit, contact Honeywell’s technical support and/or engineering depart-

ment. Honeywell’ s technical department will assist you in detailed trou-

bleshooting of the E-Mon Class 3200 meter installation and assist you

in getting the unit operating correctly.

62-0397_C.fm Page 4 Wednesday, May 9, 2018 9:28 AM

E-MON CLASS 3200 METER

5 62-0397—02

2.0 INTERNAL ELECTRONIC ASSEMBLIES

The units are comprised of two major subassembly boards, the main power board

and the display board. Both circuit boards are mounted inside a UL Type 1 (steel)

or Type 4X (rain tight) enclosure.

Fig. 1. Internal Electronic Assemblies.

2.1 Main Power Board

Connections to this board include the MAIN Power Input and current sensors.The

MAIN Power Input terminals are positions one through four on the four position

screw terminal block, TB1. These terminals are covered with a protective shield

for safety purposes. The current sensor assemblies interface to TB2, TB3 and

TB4. Each terminal block corresponds to an input voltage phase; care must be

exercised to ensure that each current sensor is connected to the correct terminal

block. One three terminal screw connector is provided for RS-485

communications.

Fig. 2. Main Power Board Connections.

M33307

MAIN

POWER

BOARD

DISPLAY

BOARD

M33308

RS-485

MAIN

POWER

INPUT

CURRENT

SENSOR

INPUT

62-0397_C.fm Page 5 Wednesday, May 9, 2018 9:28 AM

E-MON CLASS 3200 METER

62-0397—02 6

2.2 Display Board

The display board connects to the main power board via a flex ribbon cable and

the board mounts on the inside of the housing door.

The E-Mon Class 3200 meter features a 4-line LCD display that indicates

multiple meter data points.

Fig. 3. Display Board.

M33279

DOWN UP SELECT MENU

62-0397_C.fm Page 6 Wednesday, May 9, 2018 9:28 AM

E-MON CLASS 3200 METER

7 62-0397—02

3.0 METER TECHNICAL SPECIFICATIONS

Ordering Information: Define brand, class, input voltage, amperage, protocol, and

sensor type in the format A-BB-CCC-DDDD-E-FFF-GGG, where:

A = Brand: E for Honeywell E-Mon

BB = designates Class 3200 (32), or Class 5000 (50) meter

CCC = input voltage: (208, 400, 480, 600, 120 volt for High Voltage)

DDDD = current rating: (100, 200, 400, 800, 1600, 3200, 25HV)

E = enclosure: J = metal (type 1), R = non-metallic (rain tight) (type 4X), M = MMU

FFF= protocol: RTU = Modbus, BAC = BACnet, EZ7 = proprietary

“-SP”= Single or Two Phase

GGG = Sensors: KIT = split-core, SCS = solid-core, “blank” = none supplied

Brand

Class

Voltage

Amperage

Enclosure

Communication

Protocol

Current

Sensor/Option

Current

Sensor/Option

Current

Sensor/Option

Example E 32- 208 100- J RTU KIT

E32-208100-JRTUKIT

Brand E for Honeywell E-Mon

Class 3200

Voltage 120, 208, 400 (380-415), 480, 600

Amperage 2HV, 100, 200, 400, 800, 1600, 3200

Enclosure J (JIC Steel), I (Interior only), M (MMU Style), R (Rain tight)

Communication

Protocol

RTU (Modbus RTU), BAC (BACnet MS/TP), EZ7

Current Sensors/

Options

KIT (Split Core), SCS (Solid-Core), -SP (Single or Two Phase -

2 element)

Input Voltage

Configuration

3-wire (delta) Or 4-wire (wye)

Mains Voltage

Input

Up To 600 VAC RMS available

Input Power 6 VA maximum rating

Current Sensor

Rating

Up To 3200 amps RMS AC available

Power Factor 0.5 leading or lagging

Line Frequency 50-60 Hz

Metering Accuracy ANSI C12.20

62-0397_C.fm Page 7 Wednesday, May 9, 2018 9:28 AM

E-MON CLASS 3200 METER

62-0397—02 8

Temperature Range -20C to +50C

Relative Humidity

Range

0-95% non-condensing

Altitude 2000 meters maximum

Voltage Overload +25% continuously: +100% For 20 cycles

Current Sensor

Overload

100% for 1 minute

Pollution Degree Degree 2 in accordance with IEC 664

Standards EN 61326-1:2006 IEC 61010-1:2001, 2nd Edition

Installation

(Overvoltage)

Category

Category III

Enclosure Material Type 1 JIC steel or Type 4X Rain Tight

Display Readout LCD

Standard Ranges 2-Wire Delta 120 VAC: 100, 200, 400, 800,1600, 3200 Amp

4-Wire Wye 120/208 VAC: 100, 200, 400, 800,1600, 3200

Amp

3-Wire Delta 120/240 VAC: 100, 200, 400, 800,1600, 3200

Amp

4-Wire Wye 277/480 VAC: 100, 200, 400, 800,1600, 3200

Amp

2-Wire Wye 277 VAC: 100, 200, 400, 800,1600, 3200 Amp

4-Wire Wye 400 VAC: 100, 200, 400, 800,1600, 3200 Amp

3-Wire Delta 480 VAC: 100, 200, 400, 800,1600, 3200 Amp

4-Wire Wye 600 VAC: 100, 200, 400, 800,1600, 3200 Amp

RS-485 Serial

Communications

Cable

Cable: UL-listed/rated/3-

conductor, 300 VAC,

stranded conductors, 22-26

AWG.

Input/output Voltage: Ground-isolated +/-5.4Vdc

Cable Connector: Screw terminal termination

Circuit Input Isolation: 5.3kVAC

Max Cable Distance: 4000 feet

Max Network Nodes: 64 cabling nodes (including

master)

Baud Rate: 9600, 19200, 38400, 76800

Recommended

In-Line Fuse

Manufacturer: Littlefuse

Mfg. Part No: KLDR.100

Rating: 100mA, time-delay, 600VAC

cartridge fuse

62-0397_C.fm Page 8 Wednesday, May 9, 2018 9:28 AM

E-MON CLASS 3200 METER

9 62-0397—02

Battery Cell: Description: Non-rechargeable cell used

for memory retention

Manufacturer: Panasonic

Mfg Part No: CR2032

Working Voltage: 3Vdc

Current Capacity 225 mAHr

Electrolyte: Manganese Dioxide Lithium

62-0397_C.fm Page 9 Wednesday, May 9, 2018 9:28 AM

E-MON CLASS 3200 METER

62-0397—02 10

4.0 SAFETY LABEL DEFINITIONS AND

INFORMATION

The E-Mon Class 3200 meter may contain one or more of the following labels.

Operator(s) should familiarize themselves with the meaning of each label to

minimize risk.

FCC Notice

This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses and can radiate radio frequency

energy and, if not installed there is no guarantee that interference will not occur

in a particular installation. If this equipment does cause harmful interference to

radio or television reception, which can be determined by turning the equipment

off and on, the user is encouraged to try to correct the interference by one or more

of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver

- Connect the equipment into an outlet on a circuit different from that

to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

Standards Compliance:

BACnet MS/TP and IP protocol is BTL listed.

LonWorks TP/FT-10 protocol is LonMark® certified.

The presence of this label is a cautionary indicator identifying a

danger risk. The manual should be consulted prior to proceeding.

The presence of this label indicates an electrical shock hazard

exists in the location or area where the label is placed. Prior to

proceeding, the MAINS power must be disconnected and the

manual consulted for safety information.

62-0397_C.fm Page 10 Wednesday, May 9, 2018 9:28 AM

Inhaltsverzeichnis

Andere Honeywell Messgerät Handbücher

Honeywell

Honeywell QA 10 DN 25 G I Bedienungsanleitung

Honeywell

Honeywell TS34C Bedienungsanleitung

Honeywell

Honeywell EW44*A Series Handbuch

Honeywell

Honeywell C7355B Bedienungsanleitung

Honeywell

Honeywell COCON 26 DRA-LP/MP Bedienungsanleitung

Honeywell

Honeywell X4 Series Gebrauchsanweisung

Honeywell

Honeywell HAQ Series Installationsanleitung

Honeywell

Honeywell AirAlert 96d Handbuch

Honeywell

Honeywell Sensepoint XCD RTD Bedienungsanleitung

Honeywell

Honeywell E-Mon Anleitung zur Verwendung

Honeywell

Honeywell Vertex Bedienungsanleitung

Honeywell

Honeywell AC-250NXS Bedienungsanleitung

Honeywell

Honeywell VERSAFLOW SONIC 1000/TWS 9000 Bedienungsanleitung

Honeywell

Honeywell NOTIFIER AM-8200 Bedienungsanleitung

Honeywell

Honeywell 90DM4 Bedienungsanleitung

Honeywell

Honeywell HERMetic PRESS Bedienungsanleitung

Honeywell

Honeywell LeaderLine DPR 100 C Bedienungsanleitung

Honeywell

Honeywell RAE Systems NeutronRAE II Bedienungsanleitung

Honeywell

Honeywell Multiple Meter Units Bedienungsanleitung

Honeywell

Honeywell Q209E Modutrol IV Bedienungsanleitung

Honeywell

Honeywell VERSAFLOW MAG 200 Bedienungsanleitung

Honeywell

Honeywell Themis alpha EI2 Betriebsanleitung

Honeywell

Honeywell RABO G65 Bedienungsanleitung

Honeywell

Honeywell Chadwick-Helmuth 8500C Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

Keysight

Keysight M8290A Bedienungsanleitung

Acterna

Acterna MS1400 Bedienungsanleitung

R&S

R&S ZPH Bedienungsanleitung

Datacolor

Datacolor ColorReader DC10-2 Bedienungsanleitung