Honeywell EnCore FC Series Bedienungsanleitung

FC1-OI-EN h 2017-11-16

as of 2017-11-16

From Basic System version 03-22

Flow Computer

Device Series enCore FC

FC1, MC1

Manual

Operating Instructions

Page 2 of 120

Operating Instructions

enCore FC

Disclaimer

The information contained in this document is the property of Honeywell. The following

information is to be used exclusively for the intended purpose. This document or its

contents may not be reproduced, published or made available to a third party in whole

or in part without the express permission of Elster GmbH.

All information and descriptions in this Operating Instructions have been compiled

after careful examination. Nevertheless, errors cannot be completely excluded.

Honeywell therefore does not guarantee the completeness or correctness of the

content. The manual cannot be understood as a guarantee of product properties. It

also describes properties that are only available as an option.

Honeywell is in no case liable to third parties for direct, special or consequential

damages. The information in this document is subject to change without notice.

With regard to extended product liability, the data and material properties listed may

only be regarded as guidelines and must always be checked and, if necessary,

corrected on a case-by-case basis. This is particularly true where safety aspects are

concerned.

Further support is available from your local office or representative. The address can

be found on the Internet or at Honeywell.

The passing on and reproduction of this manual or parts thereof is only permitted with

the written permission of Honeywell.

If the product described herein is improperly handled, repaired or modified by

unauthorized persons or if Honeywell spare parts other than original spare parts are

used, the warranty will be void.

This product may contain or be derived from third party material, including software.

Third party material may be subject to license terms, notices, restrictions and

obligations of the Licensor. The licenses, notices, restrictions and obligations, if any,

may be found in the materials accompanying the Product, in the documents or files

containing the material of third parties, in a file called third_party_licenses on the

media containing the Product, or at www.honeywell.com/ps/thirdpartylicenses.

Dortmund, October 2017

enCore FC

Operating Instructions

Page 3 of 120

Contents

1General Information 8

1.1 The enCore/enSuite Concept 8

1.2 Scope of Delivery 9

2About these Instructions 11

2.1 Target Group Definition 11

2.2 The enCore FC Manual at a Glance 13

2.3 Text Labelling 15

2.3.1 Presentation of Safety and Risk Instructions 15

2.3.2 Paragraph Formats 16

2.3.3 Character Formats 17

2.3.4 Character Formats in Flow Charts 18

2.4 Limitation of Liability 19

2.5 Applicable Standards and Guidelines 20

3Security considerations for your network 21

4Safety 23

4.1 General Safety Instructions 23

4.2 Intended Use 25

4.3 Unacceptable use while Impaired 26

4.4 Operator Liability 26

5Design and Function 28

5.1 Functional Description of enCore FC devices 28

5.1.1 Number of Streams and their Flow Directions 29

5.1.2 International Standards 29

5.2 Device Description 30

5.3 Operation Panel 31

5.3.1 Device Keys 32

5.3.2 Touch Screen 32

Contents

Page 4 of 120

Operating Instructions

enCore FC

5.3.3 Operation and Navigation within the Display 33

5.3.4 Security Switch 36

5.3.5 LEDs 36

5.4 Interfaces (Rear Side of Device) 39

5.5 Available Process Boards 40

5.5.1 ExMFE5 Process Board 40

5.5.2 MFE7 Process Board 43

5.5.3 MSER4 Process Board 43

5.5.4 ESER4 Process Board 44

5.5.5 MFA8 Process Board 44

6Assembly Instructions 45

6.1 Line Connection 45

6.2 Power Supply and Grounding 47

6.3 Installation and Conversion of Process Boards 48

6.3.1 Insert a Process Board in a Free Board Slot 49

6.4 Connection Diagrams 54

6.4.1 General Recommendations for Signal and Data Cable 55

6.4.2 Pt100 (EEx i) via ExMFE5 Board 57

6.4.3 Pt100 (EEx d) via MFE7 Board 58

6.4.4 Analog Measurement Transmitter (EEx i) via ExMFE5 Board 59

6.4.5 Analog Measurement Transmitter (EEx d) via MFE7 Board

(without barrier) 60

6.4.6 Analog Measurement Transmitter (EEx i) via MFE7 Board

(barrier in sink mode) 61

6.4.7 Analog Measurement Transmitter (EEx i) via MFE7 Board

(barrier in source mode) 62

6.4.8 HART Measurement Transmitter (EEx i) via ExMFE5 Board 63

6.4.9 HART Measurement Transmitter (EEx d) via MFE7 Board

(without barrier, internal Power Supply) 65

6.4.10 HART Measurement Transmitter (EEx d) via MFE7 Board

(without barrier, external Power Supply) 67

6.4.11 HART Measurement Transmitter (EEx i) via MFE7 Board

(barrier in sink mode) 69

Contents

enCore FC

Operating Instructions

Page 5 of 120

6.4.12 HART Measurement Transmitter (EEx i) via MFE7 Board

(barrier in source mode) 71

6.4.13 HART Measurement Transmitter (EEx d) via MFE7 Board

(redundant, without barrier) – Burst Mode 73

6.4.14 HART Measurement Transmitter (EEx i) via MFE7 Board

(redundant, barrier in source mode) – Burst Mode 75

6.4.15 HART Measurement Transmitter (EEx d) via MFE7 Board

(Multi-Master, without barrier) – Multidrop Mode (from Basic

System 03-25) 77

6.4.16 HART Measurement Transmitter (EEx i) via MFE7 Board

(Multi-Master, barrier in source mode) – Multidrop Mode (from

Basic System 03-25) 79

6.4.17 Gas Meter (Turbine): Encoder Index, 2 LF/HF Sensors (EEx i)

via ExMFE5 Boards 81

6.4.18 Gas Meter (Turbine): Encoder Index, 2 LF/HF Sensors (EEx i)

via MFE7 Board 82

6.4.19 Gas Meter (Turbine) SMRI Bi-directional: 2 HF Sensors, Flow

Direction Detection (EEx i) via MFE7 Board 84

6.4.20 Gas Meter (Turbine) SMRI Bi-directional:

Flow Direction Detection Internal (EEx i) via MFE7 Board 85

6.4.21 Q.Sonic Ultrasound Gas Meter: Serial RS485 (EEx d) via

MFE7 Board 87

6.4.22 Q.Sonic6 Ultrasound Gas Meter: Serial RS485 (EEx d) via

MFE7 Board 88

6.4.23 FLOWSIC600 Ultrasound Gas Meter: Serial RS485 (EEx d)

via MFE7 Board 89

6.4.24 Serial Interface through COM Port (CPU or MSER4-Board) 90

6.4.25 Analog Output over MFA8 Board (0/4 ... 20 mA) 92

6.4.26 Message Output over MFA8 Board 93

6.4.27 Pulse Output over MFA8 Board 95

7Device Configuration and Commissioning 96

7.1 Device Configuration 97

7.2 Commissioning the Measurement System 98

7.2.1 Checking Device Settings 99

7.2.2 Checking Measurement Input Values 99

Contents

Page 6 of 120

Operating Instructions

enCore FC

7.2.3 Checking Output Signals 99

7.2.4 Checking Digital Communication (Modbus, etc.) 99

7.2.5 Checking Measurements and Calculations 99

7.2.6 End of Commissioning (from Basic System 03-24) 99

7.2.7 Sealing (if necessary) 100

8Maintenance 101

8.1 Battery Replacement 101

8.1.1 Changing Batteries 102

8.2 Cleaning 104

8.3 Technical Assistance Center (TAC) 105

8.4 Replacement Parts and Accessories 105

8.5 Warranty Conditions 106

9Decommissioning/Disposal 107

9.1 Storage 107

9.2 Disposal 108

10 Technical Data 109

10.1 General Information 109

10.2 Input channels 110

10.3 Outputs 111

10.4 Interfaces for Digital Communication 112

10.5 Data Protocols 112

10.5.1 Data protocols and its TCP default port (Ethernet) 113

10.6 Housing dimensions 114

10.6.1 1/3 housing width 114

10.6.2 1/2 housing width 115

11 FAQs 116

11.1 How to report a security vulnerability to Honeywell? 116

11.2 Limitations for multidrop and burst mode up to basic system version ≤

03-24 116

Contents

enCore FC

Operating Instructions

Page 7 of 120

12 Index 118

13 Appendix 120

Page 8 of 120

Operating Instructions

enCore FC

1 General Information

1.1 The enCore/enSuite Concept

enCore is the name of an Elster product platform for advanced measure-

ment devices. All enCore devices are based on the same hardware

components and software concepts. Both the hardware and software of

enCore devices have a modular design; the configuration of the process

board equipment and the arrangement of software components are variable.

On one hand, the software components consist of basic functionalities,

which are provided by the Basic System with its System Function Blocks

(abbreviated as: SFBs), and on the other hand consist of application-related

functionalities, which come with different Application Function Blocks

(abbreviated as: AFB). Owing to this modular design principle, each device

can be optimally adapted to individual requirements.

enSuite is the name of the PC software supporting all enCore devices along

with a number of other Elster devices. The enSuite software provides tools

for configuration, parameterization, diagnosis, software downloads and other

services.

Parameterization in enSuite

Please note that the changes that you make in parameterization

of enSuite become active in the device only when you activate the

action Transfer parameterization to device and after the enCore

device restarts (automatically).

volume “Configuration fo Device Software” of enCore FC

manual

1 General Information

enCore FC

Operating Instructions

Page 9 of 120

1.2 Scope of Delivery

The enCore FC's scope of delivery includes:

enCore

FC1

enCore

MC1

enCore device:

Electronic Flow Computer enCore FC1





Electronic Flow Computer enCore MC1





confirmation of conformity





factory test protocol



dispatch list/delivery note



manuals:

„Instructions for Use in Legal Metrology” (FC1 only)





„Operating Instructions”



enSuite installation CD



USB cable Type A/B



accessories (plugs incl. housing)



1.2.1 Honeywell (Elster GmbH) Contact Information

You can contact our sales and service department at:

Elster GmbH (manufacturer)

Steinern Straße 19-2155252

Mainz-Kastel/Germany

1Only for devices used in legal metrology.

2Only for devices that are not used in legal metrology.

3optional

General Information 1

Page 10 of 120

Operating Instructions

enCore FC

Phone: +49 6134 605-0

Email: info@elster.com

Website: www.elster-instromet.com

You can reach our Technical Assistance Center (TAC) at:

Phone: +49 231 937110-88

Email: ElsterSupport@Honeywell.com

Website: www.elster-instromet.com

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Honeywell Messgerät Handbücher

Honeywell

Honeywell C7355B Bedienungsanleitung

Honeywell

Honeywell GasLab Q2 Bedienungsanleitung

Honeywell

Honeywell UDA2182 Installationsanleitung

Honeywell

Honeywell HomMed Genesis Touch Bedienungsanleitung

Honeywell

Honeywell H Series Bedienungsanleitung

Honeywell

Honeywell Q340A Bedienungsanleitung

Honeywell

Honeywell TS34C Bedienungsanleitung

Honeywell

Honeywell OELD Bedienungsanleitung

Honeywell

Honeywell RABO Bedienungsanleitung

Honeywell

Honeywell SmartLine RMA800 Bedienungsanleitung

Honeywell

Honeywell AutoSet 1500 Bedienungsanleitung

Honeywell

Honeywell VERTEX C Bedienungsanleitung

Honeywell

Honeywell Green Class meter Bedienungsanleitung

Honeywell

Honeywell Elster EK280 Gebrauchsanweisung

Honeywell

Honeywell HERMetic PRESS Bedienungsanleitung

Honeywell

Honeywell RABO G65 Bedienungsanleitung

Honeywell

Honeywell EW600 Series Bedienungsanleitung

Honeywell

Honeywell RABO G16 Bedienungsanleitung

Honeywell

Honeywell Vertex Bedienungsanleitung

Honeywell

Honeywell FS24X Plus Bedienungsanleitung

Honeywell

Honeywell Q4000 Bedienungsanleitung

Honeywell

Honeywell MI Wireless Kurzanleitung

Honeywell

Honeywell Bendix/King KN 63 Bedienungsanleitung

Honeywell

Honeywell NOTIFIER UDS-3 Verdrahtungsschema

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

Keysight

Keysight M8290A Bedienungsanleitung

Acterna

Acterna MS1400 Bedienungsanleitung

R&S

R&S ZPH Bedienungsanleitung

Datacolor

Datacolor ColorReader DC10-2 Bedienungsanleitung

Honeywell enCore FC Series Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken