Honeywell Q4000 Bedienungsanleitung

Q4000_M_0302e 07/09 page 1 of 2

Q4000 Installation manual

Precautions on installation - Meter

•When installing the meter outdoors, provide shade to prevent

exposure to direct sunlight.

•Do not mount the meter with its display surface facing

downwards.

•Avoid installing the meter in a very high temperature

environment as this will shorten the battery life.

•Provide clearance around the meter pipe section for piping

work. Provide clearance (30cm or more between pipe edge

and floor) for turning a box wrench, particularly under a

meter pipe section which has lower side bolts and nuts that

are difficult to tighten.

Installation

1. Insert the studding in the lower two bolts and fix the bolts to

the flanges.

2. Place the electromagnetic meter on the studs and set it in

the desired position, taking care not to subject it

3. Insert the remaining studs and slightly tighten all bolts. Make

sure that the meter pipe centre is not displaced and the

display is not askew. Fit the gaskets in between the pipe

ends and the meter..

4. After you check the displacement of the meter pipe centre,

tighten the nuts diagonally in the order shown by the arrows in

the figure above. Tighten the nuts to squeeze the gaskets until

fully sealed.

Caution

•Make sure not to step on the display unit of the electromagnetic meter while you are

doing the pipework.

•Never try to adjust the meter position using the display unit for grip after tightening the

bolts.

•Do not attempt to correct problems by hitting the meter body.

Q4000_M_0302e 07/09 page 2 of 2

Precautions on piping

•Pipes, especially newly installed ones, often have foreign matter (such as oil) on the inside.

•Be sure to clean the pipe before installing the electromagnetic meter.

•For optimum meter performance, follow the precautions given below and install the meter

where it can be easily accessed for maintenance purposes.

•There are no restrictions regarding mounting of the meter on the pipe except the display

surface should not be facing downwards.

WARNING: The pipe must always be filled completely with the flowing fluid.

The pipe fluid outlet must be at a higher level than the portion

of pipe where the meter is installed.

A leakage at the check valve will allow air into the pipe when the

pump stops and will prevent the pipe from being completely

filled.

When installing the meter on vertical piping, make sure to mount it on a

pipe section in which the fluid flows upwards. Before the meter 5 DN, after

the meter 2 DN)

WARNING: No solid substances must be inside the pipe.

Be sure to mount the meter on a vertical section of pipe in which the fluid

flows upwards. Also install a shut-off flange for cleaning.

WARNING: A straight section of the pipe is recommended

for meter installation.

During fully open position using various valves; the meter can be

fixed directly to a gate valve being fully opened.

Applicable to various control valves, such as butterfly and ball

valves.

Be sure to install control valves towards the lower end of the

downward flow as possible.

WARNING: No air must be sucked in.

Consider the position of suction mouth..

Inhaltsverzeichnis

Andere Honeywell Messgerät Handbücher

Honeywell

Honeywell 3400 Bedienungsanleitung

Honeywell

Honeywell E-Mon Anleitung zur Verwendung

Honeywell

Honeywell EW44*A Series Handbuch

Honeywell

Honeywell A700 Bedienungsanleitung

Honeywell

Honeywell Q209E Modutrol IV Bedienungsanleitung

Honeywell

Honeywell Sensepoint XCD RTD Bedienungsanleitung

Honeywell

Honeywell Envitec MySignO Bedienungsanleitung

Honeywell

Honeywell AS302P Bedienungsanleitung

Honeywell

Honeywell H Series Bedienungsanleitung

Honeywell

Honeywell C7355A1050 Bedienungsanleitung

Honeywell

Honeywell X4 Series Gebrauchsanweisung

Honeywell

Honeywell TC809EA1035 Bedienungsanleitung

Honeywell

Honeywell Touchpoint Plus Bedienungsanleitung

Honeywell

Honeywell Multiple Meter Units Bedienungsanleitung

Honeywell

Honeywell KA 54 Bedienungsanleitung

Honeywell

Honeywell ACM 150 Betriebsanleitung

Honeywell

Honeywell themis plus EI3 Bedienungsanleitung

Honeywell

Honeywell HTRAM-V1-W Bedienungsanleitung

Honeywell

Honeywell Class 320 Meter Bedienungsanleitung

Honeywell

Honeywell SmartLine RMA801 Bedienungsanleitung

Honeywell

Honeywell RABO G16 Bedienungsanleitung

Honeywell

Honeywell BK V2 Bedienungsanleitung

Honeywell

Honeywell E-Mon Class 3200 Bedienungsanleitung

Honeywell

Honeywell enCore FC Series Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

Keysight

Keysight M8290A Bedienungsanleitung

Acterna

Acterna MS1400 Bedienungsanleitung

R&S

R&S ZPH Bedienungsanleitung

Datacolor

Datacolor ColorReader DC10-2 Bedienungsanleitung