Honeywell HPL624 Technisches Handbuch

HPL624

Power Supply/Battery Charger

PN 52263:C 1/10/08 ECN 08-029

Honeywell

12 Clintonville Road

Northford, CT 06472-1610

http://www.honeywellpower.com

Product Installation Document

1 Introduction

The HPL624 power supply/battery charger converts a low voltage AC input into an output of 6 VDC or 12 VDC @ 1.2

amps of continuous supply current or 24 VDC @ 750 mA of continuous supply current. This general purpose linear

power supply can provide additional power for a variety of applications such as access control, security and CCTV system

accessories.

2 Specifications

• Switch selectable for 6 VDC, 12 VDC or 24 VDC output.

• 1.2 amps of continuous supply current at 6 VDC or 12 VDC.*

• 750 mA of continuous supply current at 24 VDC.*

• Output that is filtered and electronically regulated.

• Built-in charger for sealed lead acid or gel type batteries.

• Maximum charge current of 500 mA.

If a battery charger is used, subtract max charge current of

500 mA from total to determine allowable load.

• Automatic switchover to stand-by battery upon AC fail.

• PTC battery protection.

• Thermal and short circuit protection with auto reset.

• LED indicators for AC input and DC output.

• Compact design (board dimension 3"L x 2.5"W x 1.5"H).

• Battery leads and foam mounting tape included.

*Specified at 25ºC ambient.

3 Voltage Output and Transformer Selection

Output Voltage/Current Switch Transformer Requirements

SW1 SW2

12 VDC @ 1.2 amps continuous supply current Closed Closed 16.5VAC / 40 VA

(model HTP1640)

24 VDC @ 750 mA continuous supply current Open Closed 24VAC / 40 VA

(model HTP2440)

6 VDC @ 1.2 amps continuous supply current Closed Open 12VAC / 20 VA

(model HTP1220)

DC +

DC –

BAT +

HPL624.wmf

TB1

DC LED

AC LED

For additional information:

• Visit our website at http://www.honeywellpower.com

• Contact Technical Support at (877) HPP-POWR

• E-mail us at hpp_techserv@honeywell.com

2HPL624 Power Supply/Charger — P/N 52263:C 1/10/08

4 Installation Instructions

The HPL624 should be installed in accordance with the National Electrical Code and Local Authority Having

Jurisdiction.

1. Mount the HPL624 Power Supply/Charger in the desired enclosure and location using supplied tape or optional

Snaptrack HST34. If mounted using screws, use #6 screws and 3/8" non-metallic spacer or supplied foam tape.

2. The HPL624 is factory set for 12 VDC. Refer to preceding table to change to 6 VDC or 24 VDC output.

3. Connect the proper transformer to terminals labeled [AC] (refer to preceding table for correct transformer selection).

4. Use 18 AWG or larger wire for all power connections (battery, DC output).

IMPORTANT! Keep a minimum spacing of 0.25" (6.35 mm) between all power-limited and nonpower-limited

wiring such as the 115VAC/60Hz Input and the battery wiring.

5. While carefully observing polarity, connect the devices to be powered to the terminals labeled [+ DC] and [DC -].

Note: To avoid potential damage, it is important to measure the output voltage prior to connecting any devices.

6. Connect the battery using the supplied battery leads to the terminals labeled [BAT +] and [DC -].

Use two (2) 12 VDC batteries connected in series for 24 VDC operation.

Note: If batteries are not used, a loss of AC will result in a loss of output voltage.

7. After batteries and AC power have been applied, both LEDs light.

8. It is recommended that the output current be measured to ensure that it does not exceed the rated maximum current.

5 LED Indicators

6 Terminal Identification

Red (DC) Green (AC) Power Supply Status

ON ON Normal operating condition.

ON OFF Loss of AC, Stand-by battery supplying power.

OFF ON No DC output. Short circuit or thermal overload condition.

OFF OFF No DC output. Loss of AC. Discharged or no battery present.

Terminal Label Function/Description

AC AC Low voltage AC input. (Refer to Voltage Output/Transformer Selection Table.)

– DC + 6 VDC – 12 VDC @ 1.2 amps continuous supply current output.

24 VDC @ 750 mA continuous supply current output.

+ BAT – Stand-by battery connections. Maximum charge rate 500 mA.

Inhaltsverzeichnis

Andere Honeywell Stromversorgung Handbücher

Honeywell

Honeywell Notifier ACPS-610/E Bedienungsanleitung

Honeywell

Honeywell 208414 Bedienungsanleitung

Honeywell

Honeywell Notifier AMPS-24/E Bedienungsanleitung

Honeywell

Honeywell HPR12DC416UL Technisches Handbuch

Honeywell

Honeywell HP300ULM Technisches Handbuch

Honeywell

Honeywell NOTIFIER ALI50EN Bedienungsanleitung

Honeywell

Honeywell HPTV2408UL Technisches Handbuch

Honeywell

Honeywell Fire-Lite FL-PS6 Bedienungsanleitung

Honeywell

Honeywell HP1205UL-4 Technisches Handbuch

Honeywell

Honeywell PMB-AUX-RTO Technisches Handbuch

Honeywell

Honeywell NOTIFIER APS2-6R/E Bedienungsanleitung

Honeywell

Honeywell 9007AX01 Bedienungsanleitung

Honeywell

Honeywell 900P01 Gebrauchs- und Pflegehandbuch

Honeywell

Honeywell PS1202A Bedienungsanleitung

Honeywell

Honeywell HPF-PS6 Bedienungsanleitung

Honeywell

Honeywell NOTIFIER FCPS-24S6 Bedienungsanleitung

Honeywell

Honeywell PS1202A00 Bedienungsanleitung

Honeywell

Honeywell HP24100WP Technisches Handbuch

Honeywell

Honeywell 9000311PWRSPLY Bedienungsanleitung

Honeywell

Honeywell HP400ULACM4CB Bedienungsanleitung

Honeywell

Honeywell HP312CX Bedienungsanleitung

Honeywell

Honeywell PS1202C Bedienungsanleitung

Honeywell

Honeywell HP400ULM Technisches Handbuch

Honeywell

Honeywell Notifier PSU7A Bedienungsanleitung

Beliebte Stromversorgung Handbücher anderer Marken

Monacor

Monacor PS-12CCD Bedienungsanleitung

VOLTIMA

VOLTIMA MagicBox 15 Bedienungsanleitung

Agilent Technologies

Agilent Technologies 6032A Bedienungsanleitung

Miller

Miller Auto Deltaweld 452 Bedienungsanleitung

BCP

BCP PUOUBK Merkblatt

HC 2210 Bedienungsanleitung

Puls

Puls CT5.241 Bedienungsanleitung

OCZ

OCZ ZX1250W Bedienungsanleitung

iseg

iseg ECH 238 Bedienungsanleitung

Power

Power XXL A Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies 6631B Bedienungsanleitung

Renogy

Renogy PHOENIX 300 Bedienungsanleitung

HP 6200B Service-Handbuch

Epson

Epson Stylus Scan 2500 Betriebsanleitung

Pulsar

Pulsar GREEN POWER CCTV PoE POE044816 Bedienungsanleitung

Puls

Puls MiniLine ML50.100 Bedienungsanleitung

Puls

Puls AS-Interface SLA4.100 Bedienungsanleitung

Kenwood

Kenwood PS-60 Bedienungsanleitung