Honeywell MaxLED 26m Bedienungsanleitung

MaxLED

Dimensional Drawings:

330mm

230mm

336mm

460mm

427mm

700mm

198mm

52mm

304mm

52mm

395mm

52mm

MaxLED 26m MaxLED 47m MaxLED 65m

Honeywell Life Safety AS, Po. Box 3514, N-3007 Drammen, Norway http://www.hls-nordic.com

Installation:

Step 2: To gain access to the battery, lift the inner plastic cover (on top of the luminaire).

Step 1: To dismantle the luminaire, push the lock/unlock button, slide the luminaire to the left and pull it

down.

Step 4: In case you use a module connect it on the PCB.

Step 5: The control of maintained or non maintained operation of the luminary is achieved through Switch

4 of DS1. For maintained operation, switch number 4 must be in ON position. For non-maintained

operation, switch number 4 must be in OFF position.

Two additional labels are included in the package, one for 3 hours duration (180) and one for 8

hours duration (480). Depending on the selected duration, the installer must remove the default 1

hour (60) label and replace it with one that has the required duration.

The user can select one of the 3 available minimum autonomy durations: 1 hour, 3 hours and 8

hours. The selection must be done while the luminaire is disconnected from AC and battery

supplies. The selection is achieved through Switches 2 & 3 of DS1. Switch 1 is not used.

Step 3: Connect the battery cable to its respective connector on the PCB.

1 2 3 4

Switch 4 = ON

Maintained operation

(default position)

1 2 3 4

Switch 4 = OFF

Non-maintained

operation

1 2 3

1 2 3 4

(default position)

3h 8h

Honeywell Life Safety AS, Po. Box 3514, N-3007 Drammen, Norway http://www.hls-nordic.com

Step 2: For double sided pictogram, insert the appropriate pictograms to both sides and refit the profile.

For single sided pictogram, there is one blind pictogram in the package.

Step 1: To insert pictograms, first unscrew the two screws holding the side profile and remove the profile.

The product contains bracket for wall mounting and spacers for ceiling mounting.

Step 2: Pass the mains cables through the cable gland. Always use in any

case round mains cable, with a diameter of 5-10mm (H05RN-F

type 2x1mm² or any other type, at least equal to it's mechanical and

electrical properties). ATTENTION!! The cable must not be

deformed in any way (This requirement is important to ensure the

IP rating). Connect the mains to terminal blocks: L for live wire, N for

neutral and PE for ground. The C1 and C2 terminals are used for

elBus communication (optional) or voltage free contact (optional).

Note: In case of battery replacement, this must be replaced with parts of the same type and characteristics. The

replacement must be performed by the manufacturer or a competent person.

Step 1: Fasten the mounting part (with screws from within) to either wall bracket (supplied), ceiling (with or without

supplied spacers). If mounted close to a wall make sure, that the unlock button is facing outwards.

Note: In case of mains power disconnection for a period of more than two months, the battery must be

disconnected.

Note: If the supply cable of the luminaire is damaged, it shall exclusively be replaced by a competent person in order

to avoid hazard.

Step 4: Slide the luminaire into the socket. The lock/unlock button appears

indicating that the luminaire is securely installed.

Important notice when installing luminaires within the same area!!!

Step 3: Tighten the cable tie around the cables.

To avoid that luminaires perform their battery test at the same day, connect the battery packs with more than

1,5 minutes inbetween.

Pictogram Installation:

Mouting Methods:

PRESS HERE

TO UNLOCK

PRESS HERE

TO UNLOCK

Power

cable Power

cable

Metal Wall Bracket

Spacers

Wall Mounting

Ceiling Mounting

At the end of their useful life the packaging, product and

batteries should be disposed of via a suitable recycling centre.

Do not dispose of with your normal household waste. Do not

burn.

Honeywell Life Safety AS, Po. Box 3514, N-3007 Drammen, Norway http://www.hls-nordic.com

Technical description

Part no.:

Battery (NiMH):

Battery Protection:

Min./Max. Charge Current: 40 / 160mA

Overcharge protection / Deep discharge protection

5 to 40 C

Up to 95%

16 hours

Produced in accordance with:

Ambient Temperature Range:

Maximum Power Consumption:

Operation Voltage:

Relative Humidity:

Charging Time:

Technical lifetime (light source):

Lumen output, normal:

> 100000 hours

280lm 550lm 900lm

MaxLED 26m MaxLED 65mMaxLED 47m

4.2W / 4.4VA 7.2W / 7.6VA 9.8W / 10.2VA

220-240V AC, 50-60 Hz

138254 138255138009

3.6V / 1.2Ah 4.8V / 1.2Ah

IP40

1h / 3h / 8h manually selected (default 1h)

Degress of cover protection:

Emergency Mode Duration:

EN 60598-1, EN 60598-2-22, EN 55015

EN 61547, EN 61000-3-2, EN 61000-3-3

Charge Voltage Range: 4 - 6V

Lumen output, emergency (1h/3h/8h): 280/110/40lm 425/170/60lm 425/170/60lm

Weight:

Expected Battery Lifetime:

Controlgear classification in accordance with IEC 62034: with automatic test function

1068 gr 1591 gr 2355 gr

4 years

It can be configured as maintained or non-maintained.

Every 15 days the luminaire will perform an emergency

operation test. This will light the exit sign for approximately 3

seconds. The red indicator LED will flash during this test

sequence.

Note: When using DALI or Wireless communication, the

frequencies and schedules for tests will instead be determined

by the connected PC software.

Every 6 months the luminaire will perform a battery condition

test. The test will last for the stated duration. The exit sign will be

lit and the yellow indicator LED will flash during this test

sequence.

Selftest functions

The MaxLED is a self-contained LED exit sign with selftest

function.

Indicator LEDs

LED Status explanation

Description

GREEN

YELLOW

RED

Normal

Charging (battery test not possible while charging

Mains off, battery not connected or charger fault

Battery fault

Battery test

Light source test

Light source fault

Battery fault and light source fault

Off On Flashing

Manual test functions

Manual tests can only be performed if both mains and battery are connected.

By pressing the test button briefly (less than 5 seconds) an emergency operation test is performed. The exit sign will be lit

for approximately 3 seconds, the red indicator LED will flash during this test sequence.

By pressing the test button for a time space between 5 and 10 seconds, a battery condition test is performed. This test will

last for the stated duration and can only be performed when the battery is fully charged (steady green indicator LED). The

exit sign will be lit and the yellow indicator LED will flash during this test sequence.

Resetting errors

Push the test button for a time space between 10 and 15 seconds to delete all indicated errors. Then the luminaire enters

regular operation mode.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Honeywell Sicherheitsausrüstung Handbücher

Honeywell

Honeywell FF-SB14 Series Handbuch

Honeywell

Honeywell GENT S4-348 Series Gebrauchsanweisung

Honeywell

Honeywell SPACEL 3500 Bedienungsanleitung

Honeywell

Honeywell A164221 Bedienungsanleitung

Honeywell

Honeywell Miller Turbolite Bedienerhandbuch

Honeywell

Honeywell NORTH OPENGO ABEKP15 Bedienungsanleitung

Honeywell

Honeywell Miller Twin Turbo G2 Connector Bedienerhandbuch

Honeywell

Honeywell Miller VC300 Bedienungsanleitung

Honeywell

Honeywell EBI XLS MASS NOTIFICATION SYSTEM Bedienungsanleitung

Honeywell

Honeywell NORTH FP100 Bedienungsanleitung

Honeywell

Honeywell FF-SYA14 Series Bedienungsanleitung

Honeywell

Honeywell 15.112.816 Bedienerhandbuch

Honeywell

Honeywell N70462910 Bedienungsanleitung

Honeywell

Honeywell Miller EN 795 Bedienungsanleitung

Honeywell

Honeywell Miller TurboLite MFL Bedienerhandbuch

Honeywell

Honeywell Miller H-Design DuraFlex Bedienungsanleitung

Honeywell

Honeywell MILLER TurboLite EXTREME MFLEC-3/6FT Bedienerhandbuch

Honeywell

Honeywell Miller DuraHoist 3Pod Bedienerhandbuch

Honeywell

Honeywell MILLER MIGHTYLITE+ MML-OGC1 Bedienungsanleitung

Honeywell

Honeywell Miller SafEscape ELITE SEHWLB FT Series Bedienungsanleitung

Honeywell

Honeywell MILLER AIRCORE Bedienungsanleitung

Honeywell

Honeywell E3 Point E3SRMNO2 Bedienungsanleitung

Honeywell

Honeywell MILLER TURBOLITE+ Series Bedienungsanleitung

Honeywell

Honeywell satronic DMG 970 Bedienungsanleitung

Beliebte Sicherheitsausrüstung Handbücher anderer Marken

Innova

Innova Xtirpa Bedienungsanleitung

bolle SAFETY

bolle SAFETY B810 Bedienungsanleitung

SHENZHEN FANHAI SANJIANG ELECTRONICS

SHENZHEN FANHAI SANJIANG ELECTRONICS A9060T Bedienungsanleitung

Hiltron security

Hiltron security POWER8E Leitfaden

Hatco

Hatco B-950P Bedienungsanleitung

Sitec

Sitec TX MATIC Bedienungsanleitung

TEUFELBERGER

TEUFELBERGER GRIP 12 Bedienungsanleitung

MSA

MSA PremAire System Bedienungsanleitung

AMC

AMC 1022M Series Bedienungsanleitung

Trinity

Trinity CASS S3 Bedienungsanleitung

CMC

CMC Helitack HotSeat Bedienungsanleitung

Force

Force P-35 Bedienungsanleitung

ACM

ACM SAFETY D200 Produkthandbuch

ROCK

ROCK P-451 AS Bedienungsanleitung

Power first

Power first 2XYR7A Service-Handbuch

SCHUBERTH

SCHUBERTH SHP 28-C Bedienungsanleitung

Trango

Trango CINCH Bedienungsanleitung

GRIDMESH ANCHOR

GRIDMESH ANCHOR GA01 Bedienungsanleitung