Honeywell FocusPRO Wi-Fi TH6000 Series Bedienungsanleitung

FocusPROTM TH6000 Series

Programmable Thermostat

® U.S. Registered Trademark. Patents pending.

Installation

Guide

Must be installed by a trained, experienced technician

Read these instructions carefully. Failure to follow these instructions

can damage the product or cause a hazardous condition.

Need Help?

For assistance with this product please visit http://yourhome.honeywell.com

or call Honeywell Customer Care toll-free at 1-800-468-1502

69-1920ES

This manual covers the following models

• TH6110D: For 1 Heat/1 Cool systems

• TH6220D: For up to 2 Heat/2 Cool systems

• TH6320U: For up to 3 Heat/2 Cool systems

(Remove battery holder to find model number)

System Types

• Gas, oil, or electric heat with air

conditioning

• Warm air, hot water, high-

efficiency furnaces, heat pumps,

steam, gravity

• Heat only — two-wire systems,

three-wire zone valves (Series

20), and normally open zone

valves

• Heat only with fan

• Cool only

• 750 mV heating systems

Installation Guide

Wallplate installation

1. Separate wallplate from thermostat.

2. Mount wallplate as shown below.

Drill 3/16" holes for drywall. Drill 7/32" holes for plaster.

Wall anchors

Wallplate

Wire hole Mounting screws

CAUTION: ELECTRICAL HAZARD

Can cause electrical shock or equipment damage. Disconnect power before

beginning installation.

MERCURY NOTICE

If this product is replacing a control that contains mercury in a sealed tube, do not

place the old control in the trash. Contact your local waste management authority for

instructions regarding recycling and proper disposal.

Pull here to remove wallplate

from new thermostat.

Remove battery holder. Insert reference card after wallplate is

mounted (see instructions, below).

It's easier to grasp the wallplate

and remove it after completely

removing the battery holder.

FocusPROTM TH6110 / TH6220 / TH6320

Power options

Keep wires in this

shaded area

Connect Cfor primary AC power

(optional if batteries are installed).

Insert batteries for primary

or backup power.

Remove factory-

installed jumper

only for two-

transformer

systems.

Conventional Terminals:

Rc 24VAC power from cooling

transformer

R 24VAC power from heating

transformer

W Heat relay (stage 1)

W2 Heat relay (stage 2)

Y Compressor contactor (stage 1)

Y2 Compressor contactor (stage 2)

G Fan relay

C 24VAC common. For 2 transformer

systems, use common wire from cooling

transformer.

Heat Pump Terminals:

Rc 24VAC power from cooling

transformer

R 24VAC power from heating

transformer

O/B Changeover valve

Y Compressor contactor (stage 1)

Y2 Compressor contactor (stage 2) -

TH6320U only

G Fan relay

Aux Auxiliary heat relay*

E Emergency heat relay*

L Sends output when set to Em. Heat

C 24VAC common

Wiring

Terminal designations

Shaded areas below apply only to TH6320U/TH6220D or as otherwise noted.

TH6110D

RcYWG RC

TH6110D

RcYG RC

TH6220D

YWGW2Y2 R

CRcYGAuxEL RC

TH6220D

TH6320U

YWGW2Y2 R

CRcYGAux

Y2L RC

TH6320U

TH6110D

RcYWG RC

TH6110D

RcYG RC

TH6220D

YWGW2Y2 R

CRcYGAuxEL RC

TH6220D

TH6320U

YWGW2Y2 R

CRcYGAux

Y2L RC

TH6320U

*Aux and E terminals combined on TH6320U only.

Installation Guide

Wiring

Wiring guide — conventional systems

Shaded areas below apply only to TH6320U/TH6220D or as otherwise noted.

NOTES

Wire specifications:

Use 18- to 22-gauge thermostat wire.

Shielded cable is not required.

[1] Power supply. Provide disconnect means and

overload protection as required.

[2] Remove jumper for 2-transformer systems.

[3] Optional 24VAC common connection.

[4] Common connection must come from cool-

ing transformer.

[5] In Installer Setup, set system type to Heat Only.

[6] In Installer Setup, set system type to 2Heat/

2Cool Conventional.

[7] In Installer Setup, set changeover valve to O

or B.

[8] In Installer Setup, set system type to 2Heat/

1Cool Heat Pump.

[9] In Installer Setup, set system type to 2Heat/

2Cool Heat Pump.

[10] In Installer Setup, set system type to 3Heat/

2Cool Heat Pump.

[11] L terminal sends a continuous output when

thermostat is set to Em. Heat. Connect to

Honeywell zoning panels to switch the panel

to Emergency Heat.

[12] Install field jumper between Aux and E if

there is no emergency heat relay.

1H/1C System

(1 transformer)

Rc Power [1]

R [R+Rc joined by jumper]

Y Compressor contactor

C 24VAC common [3]

W Heat relay

G Fan relay

Heat-only System

Rc Power [1]

R [R+Rc joined by jumper]

C 24VAC common [3]

W Heat relay

Heat-only System

(Series 20) [5]

Rc [R+Rc joined by jumper]

R Series 20 valve terminal “R” [1]

Y Series 20 valve terminal “W”

C 24VAC common [3]

W Series 20 valve terminal “B”

Heat-only System

(normally open zone valve) [5]

Rc [R+Rc joined by jumper]

R Power [1]

Y Normally open zone valve

C 24VAC common [3]

1H/1C System

(2 transformers)

Rc Power (cooling transformer) [1, 2]

R Power (heating transformer) [1, 2]

Y Compressor contactor

C 24VAC common [3, 4]

W Heat relay

G Fan relay

Heat-only System

with Fan

Rc Power [1]

R [R+Rc joined by jumper]

C 24VAC common [3]

W Heat relay

G Fan relay

Cool-only System

Rc Power [1]

R [R+Rc joined by jumper]

Y Compressor contactor

C 24VAC common [3]

G Fan relay

2H/2C System

(1 transformer) [6]

Rc Power [1]

R [R+Rc joined by jumper]

Y Compressor contactor (stage 1)

C 24VAC common [3]

W Heat relay (stage 1)

G Fan relay

W2 Heat relay (stage 2)

Y2 Compressor contactor (stage 2)

2H/2C System

(2 transformers) [6]

Rc Power (cooling transformer) [1, 2]

R Power (heating transformer) [1, 2]

Y Compressor contactor (stage 1)

C 24VAC common [3, 4]

W Heat relay (stage 1)

G Fan relay

W2 Heat relay (stage 2)

Y2 Compressor contactor (stage 2)

See [notes] below

RcW RC

RcYWGW2Y2 RC

YG R

RcYWG R

CRcWG R

RcYWG R

YW RC

Y RC

RcW RC

RcYWGW2Y2 RC

YG R

RcYWG R

CRcWG R

RcYWG R

YW RC

Y RC

RcW RC

RcYWGW2Y2 RC

YG R

RcYWG R

CRcWG R

RcYWG R

YW RC

Y RC

RcW RC

RcYWGW2Y2 RC

YG R

RcYWG R

CRcWG R

RcYWG R

YW RC

Y RC

RcW RC

RcYWGW2Y2 RC

YG R

RcYWG R

CRcWG R

RcYWG R

YW RC

Y RC

RcW RC

RcYWGW2Y2 RC

YG R

RcYWG R

CRcWG R

RcYWG R

YW RC

Y RC

RcW RC

RcYWGW2Y2 RC

YG R

RcYWG R

CRcWG R

RcYWG R

YW RC

Y RC

RcW RC

RcYWGW2Y2 RC

YG R

RcYWG R

CRcWG R

RcYWG R

YW RC

Y RC

RcW RC

RcYWGW2Y2 RC

YG R

RcYWG R

CRcWG R

RcYWG R

YW RC

Y RC

FocusPROTM TH6110 / TH6220 / TH6320

Wiring

Wiring guide — heat pump systems

Shaded areas below apply only to TH6320U/TH6220D or as otherwise noted.

Thermostat mounting

Align the 4 tabs on the wallplate with

slots on the back of the thermostat,

then push gently until the thermostat

snaps in place.

Push excess wire back into

the wall opening.

Plug wall opening with

non-flammable insulation.

1H/1C Heat

Pump System

Rc Power [1]

R [R+Rc joined by jumper]

Y Compressor contactor

C 24VAC common [3]

O/B Changeover valve [7]

G Fan relay

2H/1C Heat

Pump System

(TH6220D only) [8]

Rc Power [1]

R [R+Rc joined by jumper]

Y Compressor contactor

C 24VAC common [3]

O/B Changeover valve [7]

G Fan relay

Aux Auxiliary heat relay [12]

E Emergency heat relay [12]

L Sends output when set to Em. Heat [11]

2H/1C Heat

Pump System

(TH6320U only) [8]

Rc Power [1]

R [R+Rc joined by jumper]

Y Compressor contactor

C 24VAC common [3]

O/B Changeover valve [7]

G Fan relay

Aux/E Auxiliary/Emergency heat relay

L Sends output when set to Em. Heat [11]

2H/2C Heat

Pump System

(TH6320U only) [9]

Rc Power [1]

R [R+Rc joined by jumper]

Y Compressor contactor (stage 1)

C 24 VAC common [3]

O/B Changeover valve [7]

G Fan relay

Y2 Compressor contactor (stage 2)

L Sends output when set to Em. Heat [11]

3H/2C Heat

Pump System

(TH6320U only) [10]

Rc Power [1]

R [R+Rc joined by jumper]

Y Compressor contactor (stage 1)

C 24VAC common [3]

O/B Changeover valve [7]

G Fan relay

Aux/E Auxiliary/Emergency heat relay

Y2 Compressor contactor (stage 2)

L Sends output when set to Em. Heat [11]

See [notes] on page 4.

RcYG RC

RcYGAuxEL RC

RcYGAux

L RC

RcYGY2

RcYGAux

L RC

RcYG RC

RcYGAuxEL RC

RcYGAux

L RC

RcYGY2

RcYGAux

L RC

RcYG RC

RcYGAuxEL RC

RcYGAux

L RC

RcYGY2

RcYGAux

L RC

RcYG RC

RcYGAuxEL RC

RcYGAux

L RC

RcYGY2

RcYGAux

L RC

RcYG RC

RcYGAuxEL RC

RcYGAux

L RC

RcYGY2

RcYGAux

L RC

Installation Guide

To begin, press and hold the sand FAN

buttons until the display changes.

Function

number Setting

Press s or t to change settings.

Press NEXT to advance to the next function.

Press DONE to exit and save settings.

Done Next

Installer setup

Follow the procedure below to configure the thermostat to match the installed

heating/cooling system, and customize feature operation as desired.

Continued on next page

Setup function Settings & options (factory default in bold)

Shaded areas below apply only to TH6320U/TH6220D or as otherwise noted.

*[Other cycle rate options: 2, 4, 6, 7, 8, 10, 11 or 12 CPH]

1System type 0 1 heat/1 cool conventional

1 1 heat/1 cool heat pump (no aux. heat)

2 Heat only — 2-wire systems, 3-wire zone valves (Series 20), and

normally open zone valves

3 Heat only with fan

4 Cool only

5 2 heat/1 cool heat pump (with aux. heat)

6 2 heat/2 cool conventional

7 2 heat/1 cool conventional

8 1 heat/2 cool conventional

9 2 heat/2 cool heat pump (no aux. heat) - TH6320U only

10 3 heat/2 cool heat pump (with aux. heat) - TH6320U only

2Changeover valve

(O/B terminal)

0 Changeover valve (O/B terminal energized in cooling)

1 Changeover valve (O/B terminal energized in heating)

3Fan control

(heating)

0 Gas or oil furnace — equipment controls fan in heating

1 Electric furnace — thermostat controls fan in heating

5Stage 1 heat cycle

rate (CPH: cycles/hour)*

5 For gas or oil furnaces of less than 90% efficiency

1 For steam or gravity systems

3 For hot water systems & furnaces of over 90% efficiency

9 For electric furnaces

6Stage 2 heat cycle

rate/Auxiliary heat

cycle rate (CPH)*

5 For gas or oil furnaces of less than 90% efficiency

1 For steam or gravity systems

3 For hot water systems & furnaces of over 90% efficiency

9 For electric furnaces

7Auxiliary heat cycle

rate (CPH)*

Only TH6320U

for 3H/2C Heat Pumps

5 For gas or oil furnaces of less than 90% efficiency

1 For steam or gravity systems

3 For hot water systems & furnaces of over 90% efficiency

9 For electric furnaces

8Emergency heat cycle

rate (CPH)*

9 For electric emergency heat

1 For steam or gravity systems

3 For hot water systems & furnaces of over 90% efficiency

5 For gas or oil furnaces of less than 90% efficiency

FocusPROTM TH6110 / TH6220 / TH6320

System test System status

Shaded areas below apply only to TH6320U/TH6220D or as otherwise noted.

Press s / t to turn system on/off.

Press NEXT to advance to next test.

Press DONE to terminate system test.

Test number System status

10 0

To begin, press and hold the s and t

buttons until the display changes.

Installer setup

Setup function Settings & options (factory default in bold)

Shaded areas below apply only to TH6320U/TH6220D or as otherwise noted.

9Stage 1 compressor

cycle rate (CPH)

3 Recommended for most compressors

[Other cycle rate options: 1, 2, 4, 5 or 6 CPH]

10 Stage 2 compressor

cycle rate (CPH)

3 Recommended for most compressors

[Other cycle rate options: 1, 2, 4, 5 or 6 CPH]

12 Manual/Auto

changeover

0 Manual changeover (Heat/Cool/Off)

1 Auto changeover (Heat/Cool/Auto/Off) **See page 8

2 Auto changeover only (Auto) **See page 8

13 Adaptive Intelligent

Recovery™

1 On**See page 8

0 Off

14 Temperature

display

0 Fahrenheit

1 Celsius

15 Compressor

protection

5 Five-minute compressor off time **See page 8

[Other options: 0, 1, 2, 3 or 4-minute off time]

16 Schedule format 0 5/2 (programmable weekdays and weekends)

1 5/1/1 (weekdays, Saturday & Sunday programmable)

27 Heat temperature

range stops

90 Max. heat temperature setting is 90° F (32° C)

[Other options: 40 �F to 89 �F (4.5 �C to 31.5 �C)]�F to 89 �F (4.5 �C to 31.5 �C)]F to 89 �F (4.5 �C to 31.5 �C)]�F (4.5 �C to 31.5 �C)]F (4.5 �C to 31.5 �C)]�C to 31.5 �C)]C to 31.5 �C)]�C)]C)]

28 Cool temperature

range stops

50 Min. cool temperature setting is 50° F (10° C)

[Other options: 51 �F to 99 �F (10.5 �C to 37 �C)]�F to 99 �F (10.5 �C to 37 �C)]F to 99 �F (10.5 �C to 37 �C)]�F (10.5 �C to 37 �C)]F (10.5 �C to 37 �C)]�C to 37 �C)]C to 37 �C)]

Installer system test

10 Heating system 0 Heat and fan turn off.

1 Stage 1 heat turns on. Fan turns on if Setup Function 1 is set to 1,

5, 9 or 10 OR Setup Function 3 is set to 1 **See page 6

2 Stage 2 heat turns on

3 Stage 3 heat turns on - TH6320U only

20 Emergency heating

system

0 Heat and fan turn off

1 Heat and fan turn on

2 Stage 2 heat turns on (auxiliary heat) - TH6220D only

30 Cooling system 0 Compressor and fan turn off

1 Compressor and fan turn on

2 Stage 2 compressor turns on

40 Fan system 0 Fan turns off

1 Fan turns on

CAUTION: Compressor protection is bypassed during testing. To prevent equipment

damage, avoid cycling the compressor quickly.

Installation Guide

® U.S. Registered Trademark.

69-1920ES M.S. 03-06

Honeywell International Inc.

1985 Douglas Drive North

Golden Valley, MN 55422

http://yourhome.honeywell.com

Automation and Control Solutions

Honeywell Limited-Honeywell Limitée

35 Dynamic Drive

Scarborough, Ontario M1V4Z9

Printed in U.S.A. on recycled

paper containing at least 10%

post-consumer paper fibers.

Special functions

Auto Changeover (Setup Function 12): When set to Auto, the thermostat automatically selects

heating or cooling depending on the indoor temperature. The thermostat will automatically

adjust heat and cool settings to maintain a 3-degree separation (fixed). Note: If you select Auto

Changeover Only, the System Setting on the thermostat will stay locked in the Auto position,

preventing the user from changing it to Em Heat, Heat, Cool or Off.

Adaptive Intelligent Recovery™(Setup Function 13): Allows the thermostat to “learn” how

long the furnace and air conditioner take to reach programmed temperature settings, so the

temperature is reached at the scheduled time.

Compressor Protection (Setup Function 15): Forces the compressor to wait a few minutes

before restarting, to prevent damage. During the wait time, the message Cool On or Heat On

(heat pumps only) will flash on the display.

Accessories & replacement parts

Please contact your distributor to order replacement parts.

Battery holder. . . . . . . . . . . . . . . . . . . . . . . . . . . . Part Number 50007072-001

Cover plate assembly*. . . . . . . . . . . . . . . . . . . . . Part Number 50002883-001

12 pack of medium cover plates*. . . . . . . . . . . . Part Number 50007298-001

*Use to cover marks left by old thermostats.

Specifications

Temperature Ranges

• Heat: 40� to 90�F (4.5� to 32�C)

• Cool: 50� to 99�F (10� to 37�C)

Operating Ambient Temperature

• 32� to 120�F (0� to 48.9�C)

Shipping Temperature

• -20� to 120�F (-28.9� to 48.9�C)

Operating Relative Humidity

• 5% to 90% (non-condensing)

Physical Dimensions

• 3-9/16" H x 5-13/16" W x 1-1/2" D

91 mm H x 147 mm W x 38 mm D

Electrical Ratings

Terminal Voltage (50/60Hz) Running Current

WHeating 20-30 Vac 0.02-1.0 A

(Powerpile) 750 mV DC 100 mA DC

W2 (Aux) Heating 20-30 Vac 0.02-0.5 A

YCooling 20-30 Vac 0.02-1.0 A

Y2 Cooling 20-30 Vac 0.02-1.0 A

GFan 20-30 Vac 0.02-0.5 A

O/B Changeover 20-30 Vac 0.02-0.5 A

EEmergency heat 20-30 Vac 0.02-1.0 A

LOutput 20-30 Vac 0.02-0.5 A

Serie FocusPROTM TH6000

Termostato programable

® Marca registrada de los EE. UU. Patentes en trámite.

Guía de

instalación

Debe ser instalado por un técnico capacitado y experimentado

Lea estas instrucciones atentamente. Si no sigue estas instrucciones,

puede dañar el producto u ocasionar un riesgo.

¿Necesita asistencia?

Para obtener asistencia relacionada con este producto,

visite http://yourhome.honeywell.com o comuníquese con el número gratuito

del servicio de atención al cliente de Honeywell, llamando al 1-800-468-1502

69-1920ES

Este manual incluye los siguientes modelos:

• TH6110D: para sistemas de 1 calentador y 1 refrigerador

• TH6220D: para sistemas de 2 calentadores y 2 refrigeradores

• TH6320U: para sistemas de 3 calentadores y 2 refrigeradores

(Quite el soporte de la batería para ver el número de modelo)

Tipos de sistemas

• Sistema de calefacción de gas,

de aceite o eléctrico con aire

acondicionado

• Calefacción de aire, agua

caliente, sistemas de calefacción

de alta efectividad, bombas de

calor, vapor, gravedad

• Sólo calor: sistemas de 2 cables,

válvulas de separación de tres

cables (serie 20) y válvulas de

separación normalmente abiertas

• Sólo calor con ventilador

• Sólo frío

• Sistemas de calefacción de 750 mV

Guía de instalación

Instalación de la placa para pared

En tablarroca, realice agujeros de 3/16". En yeso, realice agujeros de 7/32".

Anclas de expansión

Placa para pared

Agujero para

el cable Tornillos de montaje

PRECAUCIÓN: RIESGO ELÉCTRICO

Puede ocasionar descargas eléctricas o dañar el equipo. Desconecte la energía

eléctrica antes de comenzar la instalación.

AVISO SOBRE EL MERCURIO

En caso de que este producto reemplace a un control que contenga mercurio

en tubo sellado, evite arrojar el viejo control a la basura. Póngase en contacto con

la autoridad local para el manejo de desechos a fin de obtener instrucciones sobre

el reciclado y la correcta eliminación de este tipo de desechos.

Hale de aquí para quitar

la placa para pared del

nuevo termostato.

Extraiga el soporte de la batería. Introduzca la tarjeta de referencia

luego de montar la placa para

pared (lea las instrucciones

que aparecen abajo).

Es más fácil quitar la placa para

pared una vez que se extrae

completamente el soporte

de la batería.

1. Quite la placa para pared del termostato.

2. Monte la placa para pared como muestra

la ilustración de abajo.

Andere Handbücher für FocusPRO Wi-Fi TH6000 Series

Inhaltsverzeichnis

Sprachen:

Andere Honeywell Thermostat Handbücher

Honeywell

Honeywell Prestige IAQ YTHX9421 Bedienungsanleitung

Honeywell

Honeywell T8132C Bedienungsanleitung

Honeywell

Honeywell Smart Series Bedienungsanleitung

Honeywell

Honeywell Chronotherm T4600 Bedienungsanleitung

Honeywell

Honeywell PRO TH4000 series Bedienungsanleitung

Honeywell

Honeywell Wi-Fi VisionPRO8000 Bedienungsanleitung

Honeywell

Honeywell TC500A Kurzanleitung zur Einrichtung

Honeywell

Honeywell TH1100DH Bedienungsanleitung

Honeywell

Honeywell 2080WL Bedienungsanleitung

Honeywell

Honeywell RCHT9610WFW2004 Bedienungsanleitung

Honeywell

Honeywell pro Series Bedienungsanleitung

Honeywell

Honeywell T834 series Bedienungsanleitung

Honeywell

Honeywell VisionPRO 8000 Series Bedienungsanleitung

Honeywell

Honeywell Digital Round T8775A Bedienungsanleitung

Honeywell

Honeywell TL8230A Bedienungsanleitung

Honeywell

Honeywell RTH111 series Bedienungsanleitung

Honeywell

Honeywell T6R-HW Bedienungsanleitung

Honeywell

Honeywell RTHL3550D1006 Bedienungsanleitung

Honeywell

Honeywell BACnet Bedienungsanleitung

Honeywell

Honeywell CM900 Bedienungsanleitung

Honeywell

Honeywell TH4210U2002 Bedienungsanleitung

Honeywell

Honeywell T834C Bedienungsanleitung

Honeywell

Honeywell VVT Bedienungsanleitung

Honeywell

Honeywell TL8100 Bedienungsanleitung

Beliebte Thermostat Handbücher anderer Marken

EWELLY

EWELLY EW-181 Bedienungsanleitung

Prolon

Prolon T1100 Montageanleitung

Computherm

Computherm Q20 Bedienungsanleitung

Heatmiser

Heatmiser neoStat Bedienungsanleitung

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat Bedienungsanleitung

Saswell

Saswell SAS920XWHB-7-S-RF Leitfaden

Aircalo

Aircalo TFP1-ET85P2 Bedienungsanleitung

Carrier

Carrier DEBONAIR 33CS Bedienungsanleitung

Lennox

Lennox iHarmony Zone Thermostat Montageanleitung

Gemtech

Gemtech GT7000 Bedienungsanleitung

Rollei

Rollei Smartes 45000 Bedienungsanleitung

Sinope

Sinope TH1300RF Bedienungsanleitung

NuTone

NuTone NTBZ48 Original Betriebsanleitung

Stelpro

Stelpro MAESTRO ASMT402AD Bedienungsanleitung

Aube Technologies

Aube Technologies TH305 Bedienungsanleitung

Powtier Controls

Powtier Controls 505MST Bedienungsanleitung

Kanmor

Kanmor Zone Control 369e Bedienungsanleitung

MICROclimate International

MICROclimate International B2 Magic Eye Bedienungsanleitung