Honeywell RCHT9610WFW2004 Bedienungsanleitung

T9 SMART THERMOSTAT

RCHT9610WFW2004

Installation Guide

Online Guides

honeywellhome.com

Search for local rebates: HoneywellHome.com/Rebates

Read before installing.

Included in your box:

Tools you will need: You may need:

Installation Guide Screws and

anchors

Phillips screwdriver Wire Stripper

Home WiFi Password

T9 WiFi

Thermostat

Small ﬂat head screwdriver

Needle-nose pliers

CWire

Adapter

(optional)

UWP

Wallplate

Pencil

Drill and drill bit

Wire labels

Level

Flashlight

Compatibility Section

For help, see:

ONLINE GUIDES AND SUPPORT VIDEOS AT: honeywellhome.com/support

SOCIAL Twitter: @Honeywell_Home, Facebook: Honeywell Home

Or contact:

EMAIL honeywellhomessupport@honeywell.com

PHONE 18006333991

• REQUIRED: A CWire (common wire) is needed for 24 VAC power. If you do not

have a CWire, then a CWire Adapter is provided.

This guide will help you determine if you have a CWire or will need to use the

included CWire Adapter (Step 10). The CWire is a wire that originates from your

heating and cooling system and needs to be connected to the C terminal on your

thermostat. There is no universal color used to designate this type of wire.

CAUTION: ELECTRICAL HAZARD

Can cause electrical shock or equipment damage. Disconnect power before beginning installation.

CAUTION: EQUIPMENT DAMAGE HAZARD

Compressor protection is bypassed during testing. To prevent equipment damage, avoid cycling the

compressor quickly.

CAUTION: MERCURY NOTICE

If this product is replacing a control that contains mercury in a sealed tube, do not place the old control

in the trash. Contact your local waste management authority for instructions regarding recycling and

proper disposal.

• Compatible with most heating, cooling, and heat pump systems

• Does not work with electric baseboard heat (120240V)

• Does not work with millivolt systems

• Does not support S terminals for indoor and outdoor sensors

• Android or iOS smartphone, tablet, or device

CWire CWire Adapter

Electrical Speciﬁcations

INPUT: 24V~@60Hz, 0.2A

Removing your old thermostat

You will need: Screwdriver, needle-nose pliers

OFF

Turn off power

To protect your equipment, turn off

the power at the breaker box or switch

that controls you heating and cooling

equipment.

Note: The thermostat off switch

will not turn off the power to the

equipment.

Check that your system is off

Change the temperature on your old

thermostat so that your system starts

heating or cooling.

If you don’t hear or feel the system turn

on within 5 minutes, the power is off.

Note: If you have a digital thermostat that

has a blank display, skip this step.

Remove your existing thermostat from

the wall plate

On most thermostats, you can take off

the thermostat by grasping and gently

pulling. Some thermostats may have

screws, buttons, or clasps.

Do not remove any wires from your

thermostat at this time!

OFF

Breaker box

Switch

Take a picture of your existing wall

plate’s wiring

In order to capture all of the letters next

to the terminals, be sure to take multiple

pictures from different angles.

You may need to reference this image

later.

Remove any jumpers

A jumper is used to connect two

terminals. It may look like a small

staple or a colored wire.

Do not discard.

Keep jumpers with your old wallplate.

Label the wires

Use the stickers provided with your new

thermostat to label each wire on your

existing wall plate.

Do not label jumpers. Your new

thermostat does not need jumpers.

Do you have a line voltage system?

Line voltage systems have thick black

wires with wire nuts or are labeled high

voltage (120V or higher).

Your system is not compatible. Call

18557335465 to ﬁnd a pro-

installer in your area.

Continue to the next step.

Wire nut

Thick black wire

Example

of a jumper

Terminals

Compatibility Check

YES

YRRC

10 Do you have a CWire?

Look at the thermostat wiring

checklist from Step 8, or the photo

you took. Is the CTerminal checked?

This means you will not need

to install the included CWire

Adapter. Skip to Installing Your

New Thermostat (page 9).

This means you don’t have

a C-wire connected to your

thermostat. Continue to next

step.

Compatibility Check

YES

Disconnect the wires and remove

the old wall plate

You may need a screwdriver to

release wires from terminals.

Tip: Wrap the wires around a pencil

to prevent them from falling in the

wall.

Write down the colors of the wires

Check the boxes and write down the color of the wires connected to terminals

that are coming from the wall. Check all that apply (not all will apply).

Terminal Wire Color Terminal Wire Color

¨A or L/A ¨R

¨CRequired* ¨Rc

¨E¨Rh

¨G¨W

¨K¨W2 or Aux

¨O/B ¨Y

¨U (1 or 2)** ¨Y2

* A C-wire or CWire Power Adapter (included) is required.

** The T9 Smart thermostat cannot control equipment wired to U1 or U2.

If there are wires in terminals that are not listed, you will need additional

wiring support. Visit honeywellhome.com/support to ﬁnd out more.

Do you have a zoning panel?

You have a zoning panel if you

have multiple thermostats and one

furnace or heating system.

CWire Adapter installation is

more complicated on zoned

systems. Call 18557335465

to ﬁnd a pro-installer.

Proceed to the next step.

Do you have an unused wire?

Look at the bundle of wires coming from the

wall.

Note: You may have to pull the bundle of wires

out from the wall to ﬁnd the unused wire.

Continue to Step 13.

Open the included CWire Adapter box

and follow the instruction guide.

Label unused wire

Label your unused wire with the

provided “C” sticker label. You may need

to use a wire stripper to expose at least

1/4 inch of the wire.

Note: If you have multiple unused wires,

then label only one wire and make note

of the color here:

Compatibility Check

YES

Only complete this section if you answered No to Step 10

Connecting Your Unused CWire

You will need: Screwdriver, ﬂashlight, wire strippers

Thermostat

Furnace

Example of unused C-wire

Zoning

Panel

Go to your furnace or heating system

This system is often located in your basement, attic or garage.

Bring a ﬂashlight and screwdriver.

Remove cover from furnace or heating

system

Open the heating and cooling system’s

cover to ﬁnd the control board. You

should see the same terminal labels that

are on your thermostat.

Note: You may need to unscrew the cover.

The control board may be at the top or

bottom.

Connect the unused wire to the

C-terminal

Note: If there are existing wires in the

C-terminal, make sure they are still

connected to the C-terminal after

connecting this wire.

Find the other end of the unused wire

Locate the bundle of wires that are the

same as the ones at your thermostat.

The unused wire should be the same

color as the one near your existing

thermostat. See Step 13 for the color you

wrote down.

Close the cover to the furnace or

heating system

Be sure the cover is completely closed.

Some systems will not power up if the

cover isn’t fully closed.

You’ve connected the C-wire.

You will NOT need to use the included

CWire Adapter.

Go back to the wall where you are installing your thermostat and continue

to “Installing Your New Thermostat” on the next page.

Installing Your New Thermostat

You will need: Level, pencil, drill and a drill bit

Thermostat Screws UWP

wallplate

WallAnchors

Position wall plate

Pull open the wall plate that was included

with your new thermostat. Insert the

bundle of wires through the back of the

wall plate.

Make sure at least 1/4-inch of each wire

is exposed for easy insertion into the wire

terminals.

Insert recommended wall anchors

It is recommended that you use the

wall anchors included in the box to

mount your thermostat.

You can use the wall plate to mark

where you want to place the wall

anchors.

a) Level the wall plate

b) Mark the location of the wall

anchors using a pencil

c) Remove the wall plate

d) Drill anchor holes.

If your box contains red anchors,

drill 7/32” holes.

If your box contains yellow

anchors, drill 3/16” holes.

e) Insert the wall anchors

f) Make sure the anchors are ﬂush

with the wall

g) Reposition the wall plate on wall

UWP

Anchors Wall

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Honeywell Thermostat Handbücher

Honeywell

Honeywell PRO 1000 Bedienungsanleitung

Honeywell

Honeywell RTH2510 Series Bedienungsanleitung

Honeywell

Honeywell T8000 Bedienungsanleitung

Honeywell

Honeywell HCW 80 Betriebsanleitung

Honeywell

Honeywell FocusPRO 5000 Bedienungsanleitung

Honeywell

Honeywell RTH4300B1000 Bedienungsanleitung

Honeywell

Honeywell RTH2410 Series Bedienungsanleitung

Honeywell

Honeywell VisionPRO THM5421C1008 Bedienungsanleitung

Honeywell

Honeywell RLV4300 Bedienungsanleitung

Honeywell

Honeywell Lyric T6 Pro Wi-Fi Bedienungsanleitung

Honeywell

Honeywell Programmable Thermostat Bedienungsanleitung

Honeywell

Honeywell TC500A Bedienungsanleitung

Honeywell

Honeywell 32207484 Bedienungsanleitung

Honeywell

Honeywell Lyric Enrollment Bedienungsanleitung

Honeywell

Honeywell T6 Pro Z-Wave Bedienungsanleitung

Honeywell

Honeywell Lyric Bedienungsanleitung

Honeywell

Honeywell TL8230A Bedienungsanleitung

Honeywell

Honeywell RTH7400 series Bedienungsanleitung

Honeywell

Honeywell RLV4300 Bedienungsanleitung

Honeywell

Honeywell T5+ Bedienungsanleitung

Honeywell

Honeywell Prestige 2.0 THX9421 Bedienungsanleitung

Honeywell

Honeywell INNCOM e7 Bedienungsanleitung

Honeywell

Honeywell PRO TH4110D Bedienungsanleitung

Honeywell

Honeywell WIFI 9000 COLOR TOUCHSCREEN Bedienungsanleitung

Beliebte Thermostat Handbücher anderer Marken

EWELLY

EWELLY EW-181 Bedienungsanleitung

Prolon

Prolon T1100 Montageanleitung

Computherm

Computherm Q20 Bedienungsanleitung

Heatmiser

Heatmiser neoStat Bedienungsanleitung

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat Bedienungsanleitung

Saswell

Saswell SAS920XWHB-7-S-RF Leitfaden

Aircalo

Aircalo TFP1-ET85P2 Bedienungsanleitung

Carrier

Carrier DEBONAIR 33CS Bedienungsanleitung

Lennox

Lennox iHarmony Zone Thermostat Montageanleitung

Gemtech

Gemtech GT7000 Bedienungsanleitung

Rollei

Rollei Smartes 45000 Bedienungsanleitung

Sinope

Sinope TH1300RF Bedienungsanleitung

NuTone

NuTone NTBZ48 Original Betriebsanleitung

Stelpro

Stelpro MAESTRO ASMT402AD Bedienungsanleitung

Aube Technologies

Aube Technologies TH305 Bedienungsanleitung

Powtier Controls

Powtier Controls 505MST Bedienungsanleitung

Kanmor

Kanmor Zone Control 369e Bedienungsanleitung

MICROclimate International

MICROclimate International B2 Magic Eye Bedienungsanleitung