Honeywell INTELLIGUARD 9000 Bedienungsanleitung

® U.S. Registered Trademark. Patents pending.

Installation Guide

Wi-Fi Thermostat

9000

color

touchscreen

HOME. Touch to display Home screen.

FAN. Select fan mode.

SYSTEM. Select system mode (heat/cool).

MENU. Touch to display options. Start here to

set a program schedule.

Current schedule. Change temperature

setting and select temporary or permanent

hold.

Indoor conditions. Shows indoor temperature

and humidity.

Current date and time.

Current status. Shows system mode (heat/

cool).

Outdoor conditions. Outdoor temperature

and humidity appear after registration.

69-2815EFS—01 2

LEVEL

HERE

M34819

W-

O/B

W2-

Aux/E

M34500A

Wallplate installation

1. Separate wallplate from thermostat.

2. Mount wallplate as shown below.

Drill 3/16" holes for drywall. Drill 7/32" holes for plaster.

Wall anchors

Wallplate

Wire hole

Mounting screws

CAUTION: ELECTRICAL HAZARD

Can cause electrical shock or equipment damage. Disconnect power before

beginning installation.

MERCURY NOTICE

If this product is replacing a control that contains mercury in a sealed tube, do

not place the old control in the trash.

Wallplate

Back of

Thermostat

3 69-2815EFS—01

CCommon wire from secondary side of cooling transformer (if 2 transformers).

KOptional wirer save module.

Rc Cooling power. Connect to secondary side of cooling system transformer.

RHeating power. Connect to secondary side of heating system transformer.

W-O/B 1st stage heat relay. Or changeover valve for heat pumps.

Y1st stage compressor contactor.

GFan relay.

W2-Aux/E 2nd stage heat relay. Or heat pump auxiliary/Emergency heat relay.

Y2 2nd stage compressor contactor.

LHeat pump system monitor.

Y2GY LW2

MCR34825

RKC WRc

Jumper Loop, a plug with a wire loop used to connect the Rto the Rc terminals,

Leave jumper loop in place in single transformer systems. Remove (unplug) jumper

loop in two transformer systems.

Terminal Designations

Wiring

MCR34820

W-

O/B

W2-

Aux/E

Remove

jumper loop

ONLY if you

have both

R and Rc

wires.

Terminal

release

Terminal

holes accept

one wire

69-2815EFS—01 4

1H/1C System

(1 transformer)

Rc Power [1]

R [R+Rc joined by jumper loop]

Y Compressor contactor

C 24VAC common

W Heat relay

G Fan relay

Heat-only System

Rc Power [1]

R[R+Rc joined by jumper loop]

C24VAC common

W Heat relay

1H/1C System

(2 transformers)

Rc Power (cooling transformer) [1, 2]

R Power (heating transformer) [1, 2]

Y Compressor contactor

C 24VAC common [3]

W Heat relay

G Fan relay

Heat-only System

with Fan

Rc Power [1]

R [R+Rc joined by jumper loop]

C 24VAC common

W Heat relay

G Fan relay

Cool-only System

Rc Power [1]

R [R+Rc joined by jumper loop]

Y Compressor contactor

C 24VAC common

G Fan relay

2H/2C System

(1 transformer)

Rc Power [1]

R [R+Rc joined by jumper loop]

Y Compressor contactor (stage 1)

C 24VAC common

W Heat relay (stage 1)

G Fan relay

W2 Heat relay (stage 2)

Y2 Compressor contactor (stage 2)

2H/2C System

(2 transformers)

Rc Power (cooling transformer) [1, 2]

RPower (heating transformer) [1, 2]

YCompressor contactor (stage 1)

C24VAC common [3]

W Heat relay (stage 1)

G Fan relay

W2 Heat relay (stage 2)

Y2 Compressor contactor (stage 2)

See [notes] below

Wiring

Wiring guide — conventional systems

NOTES

Wire specifications:

Use 18- to 22-gauge thermostat wire.

Shielded cable is not required.

[1] Power supply. Provide disconnect means and overload protection as required.

[2] Remove jumper loop for 2-transformer

systems.

[3] Common connection must come from cooling transformer.

Y2GY LW2

MCR34821

RKC WRc

Y2GY LW2

MCR34822

RKC WRc

Y2GY LW2

MCR34824

RKC WRc

Y2GY LW2

MCR34825

RKC WRc

Y2GY LW2

MCR34826

RKC WRc

Y2GY LW2

M34823

RKC WRc

Y2GY LW2

M34827

RKC WRc

Wiring Instructions

1. This thermostat requires a 24Vac common to power the thermostat. The K terminal is available for

Wiresaver module (THP9045A1023).

2. Straighten the wire. Using a pen tip to hold down the terminal, gently slide the wire into terminal hole.

Note: Terminal hole will only accept one wire.

Y2GY LW2

MCR34821

RKC WRc

Jumper Loop

5 69-2815EFS—01

1H/1C Heat

Pump System

Rc Power [1]

R [R+Rc joined by jumper loop]

Y Compressor contactor

C 24VAC common

O/B Changeover valve [7]

GFan relay

2H/1C Heat

Pump System

Rc Power [1]

R [R+Rc joined by jumper loop]

Y Compressor contactor

C 24VAC common

O/B Changeover valve [2]

GFan relay

Aux/E Auxiliary/Emergency heat relay

LSends output when set to Em. Heat

3H/2C Heat

Pump System

Rc Power [1]

R[R+Rc joined by jumper loop]

Y Compressor contactor (stage 1)

C 24VAC common

O/B Changeover valve [2]

GFan relay

Aux/E Auxiliary/Emergency heat relay

Y2 Compressor contactor (stage 2)

L Sends output when set to Em. Heat

See [notes] below

Y2GY LW2

MCR34828

RKC O/B

Rc Y2GY L

Aux/E

MCR34830

RKC O/B

Y2GY L

Aux/E

MCR34829

RKC O/B

NOTES

Wire specifications:

Use 18- to 22-gauge thermostat wire. Shielded cable is not required.

[1] Power supply. Provide disconnect means and overload protection as required.

[2] In Setup, set changeover valve to Oor B.

Wiring

Wiring guide — heat pump systems

Wiring Instructions

1. This thermostat requires a 24Vac common to power the thermostat. The K terminal is available for

Wiresaver module (THP9045A1023).

2. Straighten the wire. Using a pen tip to hold down the terminal, gently slide the wire into terminal hole.

Note: Terminal hole will only accept one wire.

Y2GY LW2

MCR34821

RKC WRc

Jumper Loop

69-2815EFS—01 6

Initial setup

Upon initial power up, or after being reset to factory defaults, the initial thermostat options

(language, location, and system type) must be set to define the heating/cooling system.

Other options can be customized later.

Follow prompts on the screen to select appropriate

options.

1. Touch the language you want the thermostat

to display, then touch Next.

2. Select Home or Business installation, then

touch Next.

3. Touch Next, or name the thermostat

location—touch THERMOSTAT and follow

the rest of the instructions.

4. Select what the thermostat will control and

touch Next.

Note: Touch the orange Help button on any

screen for more information.

5. Select the system type and touch Next. The

system type determines other selections for

completing initial setup.

6. Touch Next after making selections on each

screen.

7. Touch Done on the last screen. The

thermostat displays an option to connect to

the Wi-Fi network.

7 69-2815EFS—01

System setup

System Setup Options (MENU > System Setup)

Screen Title Settings and Options

Language English/Français/Español.

Thermostat installed

in Home/Business (Thermostat is used in a residential (default) or commercial

setting).

Your thermostat

location

Touch THERMOSTAT button to display a screen where you can enter a custom

name using a keypad. If you have only one thermostat, you can leave the

name as THERMOSTAT. For business installations you can check a box to

display the thermostat name on the home screen.

Your thermostat

controls Select Heating or Cooling or both (default).

Your system type Select Forced Air (default), Heat Pump, or Hot Water or Steam. Each option

offers different choices on the following screens.

Your forced air

heating system type Select how your forced air system is powered: Gas/Oil (default) or Electric.

Efficiency of your

heating system Select Standard Efficiency Forced Air (default) or High Efficiency Forced Air.

Your heating system

type If you selected Hot Water or Steam on “Your system type,” select the specific

heating system here.

Number of cooling

stages Select 1 Stage (default) or 2 Stages. If you are unsure, note which wires are

connected: ‘Y’ wire only (1 stage) or ‘Y’ and ‘Y2’.

Number of heating

stages Select 1 Stage (default) or 2 Stages. If you are unsure, note which wires are

connected: ‘W’ wire only (1 stage) or ‘W’ and ‘W2’.

Your fan control Select whether your thermostat (default) or heating system controls the fan.

Type of changeover

valve If you selected Heat Pump on “Your system type,“ select whether it uses a

cooling changeover valve (default) or heating changeover valve.

Number of heat

pump compressor

stages

Select 1 Stage (default) or 2 Stages. If you are unsure, note which wires are

connected: ‘Y’ wire only (1 stage) or ‘Y’ and ‘Y2’.

Your backup heat No or Yes (default)

From the home screen, touch Menu > System Setup to modify the initial system setup.

System Setup

69-2815EFS—01 8

Connecting to the Wi-Fi network

Yes

Your Network

Done

online for

remote

access

Press for info

After the initial setup, walk the homeowner

through connecting to a Wi-Fi network. Or,

refer the homeowner to the User’s Guide, so

the homeowner can connect the thermostat to

a Wi-Fi network at a later time.

1 Connect the Wi-Fi network.

Touch Yes to connect the thermostat to the

Wi-Fi network. The screen displays the

message “Searching for wireless networks.

Please wait...” after which it displays a list of

all Wi-Fi networks it can find.

Note: If you cannot complete this step now,

touch

I’ll do it later

. The thermostat will display

the home screen. Complete this process by

selecting

Wi-Fi Setup

. Continue with

Step 2.

2 Select the network.

2a Touch the name of the homeowner’s

network. The thermostat displays a

password page.

Note: If the home network is not shown on the

list, touch

Rescan

2b Using the keyboard, touch the characters

that spell out the home network

password.

2c Touch Done. The thermostat displays

“Connecting to your network. Please

wait...” then shows a “Connection

Successful” screen.

2d Touch Next to display the registration

information screen.

2e Have the homeowner register the

thermostat by going to

http://www.mytotalconnectcomfort.com

Note the Thermostat MAC and CRC;

they’ll be needed during registration. Or,

refer the homeowner to the User’s Guide.

Note: The Register Online screen remains

active until you complete registration and/or

touch Done.

3 For remote access, the homeowner or end-

user must register at

mytotalconnectcomfort.com

9 69-2815EFS—01

Setting advanced preferences

1 Touch MENU. The thermostat displays a

list of options.

2 Select Preferences >Advanced Preferences.

The thermostat displays the first screen of

options that you can change.

3 On each screen, make changes as needed,

then touch Next to display new options.

Repeat this step until you have made all

changes.

4 When you have made all changes, press

Done to save and exit.

Preferences

Advanced Preferences

Screen Title Settings and Options

Scheduling Options Select Non-programmable or Programmable. Programmable uses

default or customized programming to automatically raise and lower

temperature settings for different times of day.

Temperature Indication

Scale Select Fahrenheit or Celsius.

Heating and Cooling System

Changeover Select Manual or Automatic.

Number of Schedule Periods Select 2 Periods Per Day or 4 Periods Per Day.

Pre-occupancy Purge

Duration * Select how long the fan will run before each occupied period: Off, 1,

2, or 3 hours.

Type of Override * Select Standard to maintain the programmed periods or Initiate

Occupancy to use energy-saving settings until a user presses Start

Occupancy.

Override Duration * Select how long to maintain temperature during an override: 1-10

hours or No Limit.

Early Recovery for Heating * Select No to begin recovery on schedule or Yes to ramp up

temperature early.

Early Recovery for Cooling * Select No to begin recovery on schedule or Yes to ramp down

temperature early.

Temperature Limits Select the Minimum Cool and Maximum Heat Limit.

Keypad Lockout Select Unlocked/Partially Locked/Locked.

Clock Format Select 12 Hour or 24 Hour.

Daylight Saving Time Select Off or On. If set to On, the system will automatically change

time/date to account for daylight saving.

Indoor Display Offsets Select the number of degrees to offset indoor temperature or

percentage to offset indoor humidity.

*Available when thermostat is installed in Business mode.

69-2815EFS—01 10

Troubleshooting

If you have difficulty with your thermostat, please try the following suggestions. Most

problems can be corrected quickly and easily.

Display is

blank • Checkcircuitbreakerandresetifnecessary.

• Makesurepowerswitchatheatingandcoolingsystemison.

• Makesurefurnacedoorisclosedsecurely.

• MakesureCwireisconnected.

Cannot change

system setting

to Cool

• CheckthatSystemSetupscreen“Yourthermostatcontrols”or“Yoursystem

type” is set to match your heating and cooling equipment.

Fan does

not turn on

when heat is

required

• CheckthatSystemSetupscreen“Yourfancontrol”issettomatchyour

heating equipment.

“Wait” appears

on the screen • Compressorprotectionfeatureisengaged.Wait5minutesforthesystemto

restart safely, without damage to the compressor.

Heat pump

issues cool air

in heat mode,

or warm air in

cool mode

• CheckyoursettingforSystemSetupscreen“Typeofchangeovervalve”to

make sure it is properly configured for your system (see page 66).

Heating or

cooling system

does not

respond

• TouchSYSTEM to set system to Heat. Make sure the temperature is set

higher than the Inside temperature.

• TouchSYSTEM to set system to Cool. Make sure the temperature is set

lower than the Inside temperature.

• Checkcircuitbreakerandresetifnecessary.

• Makesurepowerswitchatheatingandcoolingsystemison.

• Makesurefurnacedoorisclosedsecurely.

• If“Wait”isdisplayed,thecompressorprotectiontimerison.Wait5minutes

for the system to restart safely, without damaging the compressor.

Heating system

is running in

cool mode

• CheckthatSystemSetupscreen“Yourthermostatcontrols”or“Yoursystem

type” is set to match your heating and cooling equipment .

Andere Handbücher für INTELLIGUARD 9000

Inhaltsverzeichnis

Sprachen:

Andere Honeywell Thermostat Handbücher

Honeywell

Honeywell DT92A Kurzanleitung

Honeywell

Honeywell T6861-F Bedienungsanleitung

Honeywell

Honeywell B Montageanleitung

Honeywell

Honeywell TB7200 Series Gebrauchs- und Pflegehandbuch

Honeywell

Honeywell FocusPRO 5000 Bedienungsanleitung

Honeywell

Honeywell RTH2300 series Bedienungsanleitung

Honeywell

Honeywell VisionPRO 8000 Bedienungsanleitung

Honeywell

Honeywell RTH2310B Bedienungsanleitung

Honeywell

Honeywell TL6120 Bedienungsanleitung

Honeywell

Honeywell RTH6400 Series Bedienungsanleitung

Honeywell

Honeywell 9000 Series Bedienungsanleitung

Honeywell

Honeywell FocusPRO Wi-Fi TH6000 Series Bedienungsanleitung

Honeywell

Honeywell RTH5100B Bedienungsanleitung

Honeywell

Honeywell LYRIC T4 Montageanleitung

Honeywell

Honeywell RTH6500WF Wi-Fi Series Bedienungsanleitung

Honeywell

Honeywell RTH1120B Bedienungsanleitung

Honeywell

Honeywell RTH2410B Bedienungsanleitung

Honeywell

Honeywell T8011F Bedienungsanleitung

Honeywell

Honeywell FocusPro TH5320R Bedienungsanleitung

Honeywell

Honeywell FocusPRO 5000 Bedienungsanleitung

Honeywell

Honeywell Honeywell Thermostat PRO TH3000 Series Bedienungsanleitung

Honeywell

Honeywell Home Pro Series Bedienungsanleitung

Honeywell

Honeywell TH6320WF01 Bedienungsanleitung

Honeywell

Honeywell PRO TH4110B Bedienungsanleitung

Beliebte Thermostat Handbücher anderer Marken

EWELLY

EWELLY EW-181 Bedienungsanleitung

Prolon

Prolon T1100 Montageanleitung

Computherm

Computherm Q20 Bedienungsanleitung

Heatmiser

Heatmiser neoStat Bedienungsanleitung

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat Bedienungsanleitung

Saswell

Saswell SAS920XWHB-7-S-RF Leitfaden

Aircalo

Aircalo TFP1-ET85P2 Bedienungsanleitung

Carrier

Carrier DEBONAIR 33CS Bedienungsanleitung

Lennox

Lennox iHarmony Zone Thermostat Montageanleitung

Gemtech

Gemtech GT7000 Bedienungsanleitung

Rollei

Rollei Smartes 45000 Bedienungsanleitung

Sinope

Sinope TH1300RF Bedienungsanleitung

NuTone

NuTone NTBZ48 Original Betriebsanleitung

Stelpro

Stelpro MAESTRO ASMT402AD Bedienungsanleitung

Aube Technologies

Aube Technologies TH305 Bedienungsanleitung

Powtier Controls

Powtier Controls 505MST Bedienungsanleitung

Kanmor

Kanmor Zone Control 369e Bedienungsanleitung

MICROclimate International

MICROclimate International B2 Magic Eye Bedienungsanleitung