Honeywell PRESTIGE THX9321 Benutzerhandbuch

Honeywell

System

Installation

Guide

THX9321/9421 Prestige °IAQ and RF ElM

With wireless accessories

Control for up to 4 HeaU2 Cool heat pump systems or up to 3HeaU2 Cool

conventional systems for residential and commercial applications.

installation guide for:

* Prestige THX9321/9421 thermostat

* Equipment Interi_aee Module (ELM)

*Portable Comfort Control

• Wireless Outdoor Sensor

• Wireless Indoor Sensor

• RedLINK '° Intemet Gateway

Quick start guide

0Install thermostat .......................................................... page 3

Install optional Equipment Interface Module (ELM) ................ 3

Power optional accessories ................................................... 4

Link thermostat to wireless network ...................................... 5

Link optional accessories to wireless network ...................... 6

Install optional sensors .......................................................... 7

Customize thermostat (installer options) ............................... 8

Wiring guides .................................................................. 10-17

Key features .................................................................... 18-25

Device replacement and specifications .......................... 26-27

DISCONNECT POWER BEFORE iNSTALLATiON. Cancauseelectricalshockor equipmentdamage,

MERCURY NOTICE: If thisproductis replacinga controlthatcontainsmercuryin a sealedtube, do not placetheold control

in thetrash,ContacttheThermostatRecyclingCorporationatwww.thermostat-recycle.orgor 800-238-8192for informationon how

andwhereto properlyandsafelydispose ofyour oldthermostat,

Must be installed by atrained, experienced technician. Readthese instructionscarefully.Failuretofollow

these instructionscan damagethe productor causea hazardouscondition.

_.3U.S.RegisteredTrademark.

System Installation Guide

Your Honeywell advantage

RedLINK TM Compatible

Increase your content and profit per job by including RedLINK TM accessories that meet

your customers comfort and convenience needs. RedLINK accessories include the Wireless

Outdoor Sensor, Portable Comfort Control (PCC), Equipment Interface Module (ELM),

RedLINK Internet Gateway, Wireless Indoor Sensor, TrueSTEAM TM humidifier with Wireless

Adapter, TrueZONE TM zoning panel with Wireless Adapter, Vent Boost Remote and Wireless

Remote.

Customizable Service Reminders

Set up to 10 service reminders. Choose from the pre-set options or customize your own.

Reminders based on date, outdoor temperature or a dry contact input witt alert customers

with instructions to contact you for assistance.

Delta TAlerts and Diagnostics

Alerts give customers a sense of security white also enabling you to service or replace the

equipment prior to a loss of heating or cooling. Based on limits you set at installation, cus-

tomers can be alerted when their system is not operating as expected. The system alert witt

instruct customers to contact you for assistance. Requires ElM.

Delta T Installer Test

Save time by viewing Delta T white running a system test to verify proper operation. Requires

ElM.

Universal Inputs = 81 and $2

Assignable inputs altow you to configure Indoor and Outdoor Temperature Sensors,

Discharge and Return Air Sensors or Dry Contact Devices. Dry Contact Devices can be

used to trip pre-set or customized alerts on the thermostat home screen. Requires ElM.

User Interaction Log

The interaction log stores history of thermostat setting changes including temperature, sys-

tem and installer setup. You can use the interaction log to save time by determining if the

issue is a system error or an accidental user error.

Configurable for Residential and Light Commercial Applications

One thermostat does it nit to meet the needs of Residential and Light Commercial applica-

tions. Simply select Residential or Commercial during the installer setup. If Commercial is

selected, the thermostat witt use commercial language, meet buitding codes and offer 365

day holiday scheduling.

USB Port for Quick Installer Setup

Save time by using a USB stick to upload installer settings and service reminders in one

simple step.

Equipment Setup Wizard

The thermostat installer uses plain language and simple questions to guide you through

the set-up process. Settings are automatically modified according to the type of equipment

selected, helping to eliminate common installation errors.

Selectable Sensors

When paired with a Wireless Indoor Sensor(s) you have the ability to choose which

sensor(s) to use for temperature, humidification and dehumidification. They can be used

in combination for temperature averaging--or individually--to condition humidity levets in

separate spaces.

69-2490--03 2

THX9321/9421 Prestige _IAQ and RF ElM

Install thermostat

THX9421 : Mount the thermostat and wire to O and R terminals of the MCR32387

Equipment Interface Module (ELM), or to a separate 24 volt transformer (not

provided).

THX9321: Install and wire as above if using ElM. if not, see pages 13=15.

When usedwiththe ElM,the relaysin thethermostatdo not function,

O Install Equipment Interface Module (if used)

[If no ElM is used, skip to Section 3.]

Use screws & anchors as appropriate for the mounting surface. Mount the ElM

near the HVAO equipment, or on the equipment itself.

strip 1/4"insulation,theninsert wiresas shown.

NOTE:Ifyou installmore thanonethermostatand

ElM,the ElMsmustbe at least2 feetapart,

MCR32389

If installinga discharge/return air sensor, it must

be locatedbetweenthe IAQequipmentandthe

heating/coolingequipment.Thesensorsmustbe

in air thatis mixedwell (awayfroma-c0il/heat

exchanger).See page7.

69-2490--03

System /nstallation Guide

Power optional accessories

[If no wireless accessories are used, skip to Section 4.]

Outdoor air sensor indoor air sensor Portable Comfort Control

0_0

MCR32937

Install2freshAAlithiumbatteries

MCR32938

Install2freshAAAalkalinebatteries MCR32939

Install 3 freshAAalkalinebatteries

RedL|NK TM lnternet Gateway

The Honeywell RedLINK Internet Gateway gives your customers remote access

to home climate=control systems from any location with Internet access.

Using a Web browser, users can review and adjust indoor temperature,

system mode and other settings. The Gateway can also send alerts to as many

as 6 email addresses if a problem occurs.

ConnectRedLINKGatewaytoa

routeror modemwith Ethernet

cable(RJ45).

A Connectpowercordto

II _nn_lr_trid_ly°aUtle_lln°titch

M32940

69-2490--03 4

THX9321/942fPrestige_IAQ and RF ElM

OLink thermostat to the wireless network

(if used with an ElM or TrueZONE Wireless Adapter)

Next, link all components and RedLINK 'Maccessories to the wireless network.

|nitiai powerup configuration

When the thermostat is first activated, it wilt lead you through the steps

necessary to define and set up your system. The steps will change depending on

the type of system and thermostat you're installing.

Setup options for THX9321 Setup options for THX9421

If non-zonedsystem: If non-zonedsystem:

*Setup forthermostatonly *Setup forElM connection

,Setup foruse with ElM

If zonedsystem:

*Setup forElM wiredto zonepanel

,Setup br thermostatwired tozonepanel

,Setup forRedLINKwireless connectiontozone panel

(usingTHM400OTrueZONEWirelessAdapter)

If zonedsystem:

•Setup br ElM wiredto zonepanel

•Setup forRedLINKwireless connectiontozone panel

(usingTHM400OTrueZONEWirelessAdapter)

Link thermostat to ElM or TrueZONE _Wireless Adapter

Use the step-by=step thermostat menus to define your system type (above).

When you reach the Wireless Setup screen, follow the steps below:

M_;R32941

"Connected" status light

•Green flashing: InWirelessSetup mode.

•Green steady: Systemisworking normally,

Pressand releasethe CONNECTbuttonatthe ElMor Wireless

Adapter,andmake surethe "Connected"lightis flashinggreen.

If the "Connected"lightdoesnotflash, makesure no other

RedLINKdevicesare inWirelessSetup mode,then try again.

If the "Connected"lightdoesnotflash on theWireless

Adapter,consulttheTrueZONEmanualforhelp.

Red: Wirelessdevice(s)notcommunicating.CheckElM andRedLINKdevices.

Whilethe ElM lightisflashing,press NEXTto link

the thermostatwith the ElM.Aftera brief delay,

the screenwill display"DeviceConnected."

At any screenyou can press HELPfor moreinformation,

or pressBACKto change earlieroptions.

5 69-2490--03

System/nstallationGuide

Link optional accessories to wireless network

While the Add Device screen is displayed

on the thermostat, press and release the

CONNECT button on each wireless device, as

described below. Accessories need to be at

least 2 feet away from the thermostat or ElM

during the linking process.

PressDONEafter all deviceshavebeen linked

Wireless outdoor sensor

Pressandrelease CONNECT.After

a shortdelaythe thermostatwill

displayoutdoortemperatureand

humidity.

Portable Comfort Control

Wireless indoor sensor

Pressandrelease CONNECT.

Aftera short delay,thestatus light

willglow greenfor15 seconds.

Ifthe statuslightturns red,

thesensordidnot linkwith the

thermostat.

Innormaloperation,this light

remainsoff.If itbeginsflashing

red,batteriesare low(powerwill

be depletedafter3 weeks).

MCR32942

PressCONNECTon the PortableComfortControldisplayscreen.Press DONEwhen the

screendisplays "Connected,"then exitor continueto linkanotherthermostat.

Error messages:

E1 29 Incompatibledevicecannotbe connected.

E1 34 LowRFsignal. Movedeviceto adifferent locationand try again.

E1 38 Makesure the thermostator the ElM is inWirelessSetup mode,

andthe PortableComfortControlis at least 2feet away(600ram).

The linkingprocedurewilltime out ifthere is no keypressfor 30 minutes.Tobeginagain,

press andholdthe blankspacein the lowerright cornerofthe screen(anarrow may

appear here).Holduntilthe displaychanges (about3 seconds).

RedLiNK |nternet Gateway Pressandreleasethe buttonon the bottomofthe Internet

Gateway.After a shortdelay,the RedLINKstatuslightwillglow

steadygreen.

MCR32943

The InternetGatewaymustbe registeredonlinebefore

use atwww.mytotalconnectcomfort.com.Enterthe MAC

IDand MACCRC numberslocatedon the bottomof

the InternetGateway.Foradditionalinformation,see

instructionsprovidedwith the device.

69-2490--03 6

Install optional sensors

[If no sensors are used, skip to Section 7.]

THX9321/9421 Prestige _IAQ and RF ElM

To install outdoor air sensor

1 Mount the sensor on a vertical

exterior wall, at least 6inches below

any overhang. Choose a location

protected from direct sunlight.

2 Place sensor securely in bracket,

facing away from wall.

M2_4_,

To install indoor air sensor

1 Remove the waltptate and mount it 4

to 6 feet above the floor on an interior

watt. Drill 3/16=inch holes for drywall,

7/32=inch for plaster.

2 Attach sensor securely to watlplate as

shown.

M32936

To install discharge/return air sensor

1Instalt the sensor between the IAQ

equipment and the heating/cooling

equipment. The sensors must be in air

that is mixed well (away from a=coiV

heat exchanger).

2 Drill 1/4=inch hole for the sensor

probe and mount it to the ductwork

with enclosed screws.

Connect wires to Sl or S2 terminals at

the ElM.

Z69-2490--03

SystemInstallationGuide

0Setup installer options {ISU)

To configure the thermostat, press MENU>INSTALLEROPTIONS,then enter date

code when prompted (printed on back of thermostat). Or press MENU> EQUIPMENT

STATUSto find the date code.

A brief summary of installer options follows. You can download a complete list of

all options at _://customer.honeyweH.com.

Press CREATE SETUP to set at_ system

settings one by one.

Press VIEW/EDIT to select a specific

function and make quick changes.

TIP: Youcan use thethermostatUSB portto downloadallsystemconfigurationandinstalleroptions,includingyour company

nameandcontactinformation.Youcan uploadthisdata to eachthermostatyou install,tosave time.

R:ResidentialC:CommercialB:Both Thermostatfunctions ke i,_ i requirean ElM (seepage3),

1000 Lanqua_ B

1010 Residential/Commercial B

1020 Zone Number B

1030 DeviceName B

1030 DeviceNameon HomeScreen C

1040 Programmable/Non-programmable B

1050 Fahrenheit/Celsius B

1060 OutdoorAir Sensor B

2000 HeatingSystemType B

2010 HeatingEquipmentType B

2020-2100 Heat Stages B

2050 GeothermalForcedAir System B

2060 ReversingValveO/B B

2070-2090 Cool/CompressorStages B

2110 FanOperationin Heat B

2120,2180 BackupHeatType B

2130,2170 BackupHeatStages B

2150,2200 BackupHeatOperation B

2160,2210 BackupHeat FanOperation B

2190 ExternalFossilFuel Kit B

2220 L/ATerminalSetup C

3000 Manual/AutoChangeover B

3000 AutoChanqeoverDeadband B

3010 TemperatureControl Options B

3020 FinishWith HighCool Stage B

3021 FinishWith High HeatStage B

3030 StagingControl- Cool Differentials B

3040-3060 StagingControl- Heat Differentials B

3070 BalancePoint Onlyor Differential B

3080,3090 StagingControl- BackupHeat Differentials B

3110 BackupHeat UpstageTimer B

3120 OutdoorCompressorLockout B

3120 OutdoorBackupHeat Lockout B

3130,3150 Heat CyclesPerHour B

3140 CoolCycles PerHour B

3160 BackupHeatCycles PerHour B

69-2490--03

3170-3190 C__e raI, Throttlin ran e C

3200-3220 HeatingDerivative,Integral,Throttlingrange C

3240 MinimumCompressorOffTime B

3260 ExtendedFanRunTime in Cool B

3260 ExtendedFanRunTime in Heat B

4000 Numberof ScheduledPeriods B

4010 Pre-occupancyPurgeDuration C

4020 Override:Standardor InitiateOccuap_ C

4030 OverrideDuration C

4050 MinimumRecoverySettings- Heat C

4060 MaximumRecoverySettings- Heat C

4070 MinimumRecoverySettings- Cool C

4080 MaximumRecoverySettings- Cool C

4090 AdaptiveIntelligentRecovery R

4100 MinimumCoolSetpoint B

4100 MaximumHeatSetpoint B

4110 KeypadLockout B

4120 WirelessRemote*-

Home/OccupiedCoolSetpoint B

4120 WirelessRemote*

Home/OccupiedHeat Setpoint B

4130 WirelessRemote*

Away/UnoccupiedCool Setpoint B

4130 WirelessRemote*

Away/UnoccupiedHeat Setpoint B

4140 WirelessRemote*

Vacation/HolidayCool Setpoint B

4140 WirelessRemote*

Vacation/HolidayHeat Setpoint B

_!_:i_i_i!ii_!ii;iiiiiiii;i!_!_i_!_ii_iiii_iiii_iiii_iiii_iiii_iiii_iii_i!_ii_i_!_i_!i_i_i_!_!_!_{_!_!_!_ii_i_!_;i!_!_i!_!_i_i_!_i_;_i_iii_i_ii!iiii_iiii_iii_!_iiii_iiiii_i_!_!_!ii¸ii!iiiiiiii_i_!i_ili¸i!i!iiiiiiiiiiii_iiiiiii_i_i!iiiiiiiiiiiiiiiii_iiiiiii_iiiiiii_!i!_!

5040 IndoorSensorsUsedbrTemperature Control B

*WirelessRemote- comingsoon.

THX9321/9421 Prestige ®IAQ and RF ElM

installer options (ISU)

Thermostatfunctionsm ;ke_:i_:ay_ i requirean ElM (seepage3),

_,!,!i!_ii!_!!!_!_!!ii!i!i!!!i!iii!!!!ii!!!i!_!_i_¸i_!$_i_!!!ii_!!!_!!_i!i!!!i!i!i!_!i_i_!!!_!_!!!!_!!i!!i_i_i!_!iii!!i_ii!i!i!ii_i_i_i_i_i_!_!_!i!_!_!_!_!_!iii!i!i!i!i!i!_!_i_!

7000 FilterType B

7020 HumberofAir Filters B

7110 Air FilterReplacementReminder B

7110 Air Filter2 ReplacementReminder B

7120 EACCell CleaningReminder B

7120 EACPre-Filter CleaningReminder B

7120 EACPost-FilterReplacementReminder B

8000 HumidifierType B

8010

8030

8050

8060

8070

8080

8100

9000

9010

9020

9040

9050

9070

9080

9090

9100

9110

IndoorSensorUsedforHumidificationControl B

TerminalsWired tothe Humidifier B

Humidification-WindowProtection B

SystemModesAllowing Humidification B

HumidificationControl B

HumidifierLockout B

CleanTank/WaterFilterReplacementReminderB

HumidifierPad ReplacementReminder B

DehumidificationEquipment B

IndoorSensorUsedfor DehumidificationControl B

HumiditySensorDisplayedonthe HomeScreen B

TerminalsWired toDehumidificationEquipment B

A/Cwith LowSpeed FanSetup B

HotGas BypassSetup C

Dehumidification- OvercoolinqLimit R

9120 SystemModesAllowing Dehumidification B

9130 DehumidifierFanControl B

9140 DehumidifierLockout B

9180 DehumidificationAwayMode B

9190 DehumidificationAwayMode- FanControl B

9200 DehumidificationAway Mode-

LowLimitTemperature B

9200 DehumidificationAwayMode-

TemperatureSetting B

9200 DehumidificationAwayMode-

DehumidificationSetting B

9210 DehumidifierFilterReplacementReminder B

10000 VentilationType B

10020 TerminalsWiredto Ventilator/FreshAir Damper B

10050 VentilationControlMethod B

10060 VentilationFanControl B

10090 Numberof Bedrooms R

10090 Sizeof House R

10100 VentilationLevel(CFM) R

10120 VentilationPercentOnTime B

10130 VentilationLowTemperatureLockout B

10130 VentilationHighTemperatureLockout B

10130 VentilationHigh DewpointLockout B

10140 LockoutVentilationon Hum/DehumCalls B

10160 Ventilateon HighIndoorHumidity B

10170 VentilatorCoreCleaninq Reminder B

10170 VentilatorFilter CleaningReminder B

11000 Numberof UVDevices B

11050 UV BulbReplacementReminder B

11050 UV Bulb2 ReplacementReminder B

12000 InstallerCustomReminders B

14000 ClockFormat B

14010 DaylightSavingTime B

14020 IndoorTemperatureDisplayOffset B

14020 IndoorHumidityDisplayOffset B

15000-15020Dealer name,phone,email,website,message B

DehumidificationControl C

DehumidificationMinimumOnTime C

High HumidityComfort ResetSetting C

DehumidificationHighLimit RangeStop C

9 69-2490--03

System/nstallationGuide

ElM wiring guide -- conventional systems

Typical wiring of a conventional system with up to 3=stage heat and 2-stage cool

with one transformer.

"-POWER r--m

HEAT r"_

COOL

FAN

U1 r-_

_ U3 r==l

TO TH ERMOSTAT

SONV

W3-

________ _-

tic-

FURNACE

TRANSFORMER

____JCONs_EO20_sT4ONAL

Sl AND $2 TERMINALS

See guideson followingpagesforthermostatwiring andgeothermalradiantheatwiring.

A Wirea maximumof 2 sensorsusingthe $1 and$2 terminals.See ISU5000-6190for options.

A Removejumper(s)if usingseparatetransformers.

,_ See Economizerwiring section.

See followingpagesforadditionalthermostatwiring guidlinesforheat pumps,

geothermalsystemsandoptionalEconomizer.

69-2490--03 10

Andere Handbücher für PRESTIGE THX9321

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Honeywell Thermostat Handbücher

Honeywell

Honeywell BACnet Bedienungsanleitung

Honeywell

Honeywell Deluxe Bedienungsanleitung

Honeywell

Honeywell INTELLIGUARD 9000 Bedienungsanleitung

Honeywell

Honeywell RTHL221 series Bedienungsanleitung

Honeywell

Honeywell TH2210DV Bedienungsanleitung

Honeywell

Honeywell TH115-AF-GA Bedienungsanleitung

Honeywell

Honeywell T8131A Bedienungsanleitung

Honeywell

Honeywell T810A Bedienungsanleitung

Honeywell

Honeywell EASY-TO-SEE T87N Bedienungsanleitung

Honeywell

Honeywell CT40A Bedienungsanleitung

Honeywell

Honeywell RTH6360 Series Bedienungsanleitung

Honeywell

Honeywell RTH5100B Bedienungsanleitung

Honeywell

Honeywell FocusPRO TH5000 Series Bedienungsanleitung

Honeywell

Honeywell Powerpile TS86A Bedienungsanleitung

Honeywell

Honeywell CM921 Montageanleitung

Honeywell

Honeywell Q682 Bedienungsanleitung

Honeywell

Honeywell CM721 Bedienungsanleitung

Honeywell

Honeywell Round Bedienungsanleitung

Honeywell

Honeywell EConnect TL9160AR Bedienungsanleitung

Honeywell

Honeywell T4 Pro Bedienungsanleitung

Honeywell

Honeywell RTHL221 series Bedienungsanleitung

Honeywell

Honeywell TRADELINE Q7100A Bedienungsanleitung

Honeywell

Honeywell thr840duk Bedienungsanleitung

Honeywell

Honeywell RTH2520B Bedienungsanleitung

Beliebte Thermostat Handbücher anderer Marken

EWELLY

EWELLY EW-181 Bedienungsanleitung

Prolon

Prolon T1100 Montageanleitung

Computherm

Computherm Q20 Bedienungsanleitung

Heatmiser

Heatmiser neoStat Bedienungsanleitung

Aube Technologies

Aube Technologies TH111GFCI-NP 240 VCA Bedienungsanleitung

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat Bedienungsanleitung

Saswell

Saswell SAS920XWHB-7-S-RF Leitfaden

Aircalo

Aircalo TFP1-ET85P2 Bedienungsanleitung

Carrier

Carrier DEBONAIR 33CS Bedienungsanleitung

Lennox

Lennox iHarmony Zone Thermostat Montageanleitung

Gemtech

Gemtech GT7000 Bedienungsanleitung

Rollei

Rollei Smartes 45000 Bedienungsanleitung

Sinope

Sinope TH1300RF Bedienungsanleitung

NuTone

NuTone NTBZ48 Original Betriebsanleitung

Stelpro

Stelpro MAESTRO ASMT402AD Bedienungsanleitung

Aube Technologies

Aube Technologies TH305 Bedienungsanleitung

Powtier Controls

Powtier Controls 505MST Bedienungsanleitung

Kanmor

Kanmor Zone Control 369e Bedienungsanleitung