Honeywell PRO 1000 Bedienungsanleitung

Installation Manual

Guide d’installation

Guía de instalación

Honeywell

Série PRO 1000 / 2000 Series

Programmable and Non-programmable Thermostats

Thermostats programmables et non programmables

Termostatos programables y no programables

69-1968EFS-08

PRO 1000 / 2000 Series

Programmable and Non-programmable Thermostats

This manual covers the following models:

TH 00D, TH 0D and TH 2 0D

non-programmable thermostats TH2 0D and TH22 0D

programmable thermostats

(Remove the thermostat from ts wallplate to f nd the model number.)

System Types

TH 0D and TH2 0D:

• Central heat ng - gas, o l, electr c or

h gh-eff c ency furnace (1 H)

• Central heat ng (see above) w th a r

cond t on ng (1H/1C)

• Hot water system (steam or grav ty) w th or

w thout pump

• Central a r cond t oners

• 750 mV heat ng systems

• Heat pumps w thout aux l ary heat ng (1H/1C)

TH 2 0D and TH22 0D:

• Heat pumps w th aux l ary heat ng (2H/1C)

TH 00D:

• Central heat ng - gas, o l, electr c or

h gh-eff c ency furnace (1H)

• Hot water system (steam or grav ty) w th or

w thout pump

• 750 mV heat ng systems

Must be installed by a trained, experienced technician

Read these nstruct ons carefully. Fa lure to follow these nstruct ons

can damage the product or cause a hazardous cond t on.

Need Help?

For ass stance w th th s product please v s t http://yourhome.honeywell.com

or call Honeywell Customer Care toll-free at -800-468- 502.

ENGLISH

Installation Guide

Wallplate installation

CAUTION: ELECTRICAL HAZARD

Can cause electr cal shock or equ pment damage. D sconnect power

before beg nn ng nstallat on.

1 Loosen the lock ng screw at the bottom of the thermostat. Note that the screw s

capt ve and cannot be removed from the wallplate.

2 Separate the thermostat from the wallplate as per F gure 1.

3 Pos t on the wallplate aga nst the wall and mark hole pos t ons w th a pencl.

NOTE: Levelling is for esthetics onl and will not affect the performance of the

thermostat.

4 Drll holes at the marked pos t ons and nsert suppl ed wall anchors.

5 Pass the w res through the large open ng located at the bottom center of the wallplate

as per F gure 2.

6 Secure the wallplate to the wall w th suppl ed mount ng screws as per F gure 3.

7 Connect the w res to the term nals.

MERCURY NOTICE

If th s product s replac ng a control that conta ns mercury n a sealed tube,

do not place the old control n the trash. Contact your local waste

management author ty for nstruct ons regard ng recycl ng and proper

d sposal.

PRO 1000 / 2000 Series

Wiring

A Power supply. Prov de d sconnect means and overload protect on as requ red.

A Set the O/B jumper accord ng to the type of revers ng valve (see page 4).

A Use a p ece of w re (not suppl ed) to connect W and Y term nals to each other.

Opt onal 24 VAC common connect on. If th s connect on s not made, use batter es

to power the thermostat.

A Th s connect on s not requ red for systems that prov de heat ng only.

A Th s connect on s not requ red for systems that prov de cool ng only.

Th s connect on s not requ red for systems that do not have an a r rec rculat ng fan.

Ga s, oil or electric heating (1H )

AUse

TH 00D

Ga s, oil or electric heating and/or air conditio ning (1H / 1 C / 1 H 1 C )

- m

[Ç}

Compressor ] 0

][G

Fan

Reversing valve] |q/b[

Auxiliary Heat^ |au#e|

R

C-

A-

- G

- 0/B

- «IKE

Use

TH 2 0D

TH22 0D

ENGLISH

Installation Guide

Reversing valve setting

NOTE: This setting is necessar onl if the thermostat is connected to a heat pump.

The jumper s located on the back of the thermostat faceplate. Set t accord ng to the type

of revers ng (changeover) valve used by the heat pump.

• O (factory sett ng): The revers ng valve s energ zed when the System sw tch s set to

Cool (cool ng mode).

• B : The revers ng valve s energ zed when the System sw tch s set to Heat (heat ng

mode).

Incorrect ju m p er s ettin g: The heat pump operat on w ll be reversed; .e., t w ll cool n

Heat mode and w ll heat n Cool mode.

Fan operation setting

NOTE: This setting is not applicable if a fan is not connected to the G terminal.

A jumper, located on the back of the thermostat faceplate, determ nes how the fan operates

n Automat c mode. Th s jumper s not ava lable on TH1100, TH1210D and TH2210D. On

the TH1210D and TH2210D models, when the fan s placed n Automat c mode, t starts

r ght away when there s a call for heat or cool.

• HG (factory sett ng): Leave the jum per n th s pos t on for gas or o l heat ng systems. In th s

pos t on, the heat ng system controls the fan operat on. When there s a call for heat, the fan

starts only when the a r com ng out of the vents s suff c ently warm. When there s a call for

cool, the fan starts r ght away.

• HE: Place the jumper to th s pos t on for heat pump or electr c heat ng systems. In th s pos t on,

the thermostat act vates the fan as soon as there s a call for heat or cool.

Incorrect ju m p e r se ttin g: An ncorrect sett ng s not ceable n a gas or ol heat ng system.

When heat ng starts, you w ll n t ally feel cold a r com ng out of the vents as the fan s

runn ng before the furnace has enough t me to heat up the ar.

Battery installation

If a 24-VAC common w re s connected to the C term nal, batter es are

optional and serve to prov de backup power.

If a 24-VAC common w re s not connected to the C term nal, batter es

are nec essary to power the thermostat.

Install 2 AAA batter es on the back of the thermostat faceplate as

shown.

Thermostat mounting

1 Al gn the two brackets on the top of the thermostat w th the

correspond ng slots on the top of the wallplate.

2 Push the faceplate aga nst the wallplate.

3 T ghten the screw at the bottom of the thermostat.

PRO 1000 / 2000 Series

Installer setup

Follow the procedure below to personal ze and

conf gure the thermostat accord ng to the heat ng/

cool ng system.

1 Press ^ and s multaneously (for three

seconds) unt l the d splay appears as

shown on the r ght.

2 Press z\ or to change the opt on.

3 Press /v and for one second to advance

to the next funct on.

4 When the last funct on s d splayed, press

and to save any changes and ex t the

menu.

NOTE: If o u do n o t p re ss a n b u tton fo r 60 se conds

while o u are in the se tup m enu, the the rm o sta t a u to m a tica ll saves a n cha ng es m a de a n d exits

the m e nu . F o r pro gra m m a b le m odels onl , a t a n tim e o u can sa ve the change s a n d e x it b

pre ssing the Run button.

Function

- number

- Option

number

Funct on1 Default

sett ng Opt ons

1 Temperature d splay format 0 0: Fahrenhe t

1: Cels us

2 T me d splay format 0 0: 12-hour d splay

1: 24-hour d splay

3 Heat ng cycles per hour 5

2 to 6 cycles per hour

• 2: 30 m n (steam, grav ty)

• 3: 20 m n (hot water, 90%+ h gh-eff c ency furnace)

• 4: 15 m n (gas or ol)

• 5: 12 m n (gas or ol)

• 6: 10 m n (electr c)

4 Cool ng cycles per hour 3 2 to 6 cycles per hour

5 Compressor protect on2 10: Off

1: On

6 Adapt ve Intell gent Recovery3 10: Off

1: On

7 Appl cat on4 00: Indoor mode: 40°F to 90°F (4.5°C to 32°C)

1: Garage mode: 35°F to 90°F (1.5°C to 32°C)

1 Depend ng on your thermostat model or your system type, some funct ons are non-ava lable or

non-appl cable.

2 Damage can occur f the compressor s restarted too soon after shutdown. Th s feature forces the

compressor to wa t 5 m nutes before restart ng. Dur ng the wa t t me, the message Cool On or Heat On

flashes on the screen. When the safe wa t t me has elapsed, the message stops flash ng and the compressor

turns on.

3 Adapt ve Intell gent Recovery™ allows the thermostat to “learn” how long your furnace or a r cond t oner

takes to reach the set temperature. S mply program the des red t mes and des red temperatures nto the

schedule. The thermostat w ll determ ne when to act vate heat ng or cool ng so that the des red temperature

s atta ned at the des red t me.

4 In Indoor mode, the m n mum setpo nt s 40°F (5°C) for frost protect on. In Garage mode, the m n mum

setpo nt s 35°F (1.5°C) for energy sav ngs.

ENGLISH

Installation Guide

Specifications

Temperature Ranges

• Heat: 40 °F to 90 °F (4.5 °C to 32 °C)*

• Cool: 50 °F to 99 °F (10 °C to 37 °C)

Operating Ambient Temperature

• 32 °F to 122 °F (0 °C to 50 °C)

Shipping Temperature

• -40 °F to 130 °F (-40 °C to 55 °C)

Operating Relative Humidity

• 5% to 90% (non-condens ng)

Physical Dimensions

• 4.7” H x 2.9” W x 1.1” D (120 mm H x 74 mm W x 28 mm D)

Power Supply

• 24 VAC or 2 AAA batter es

Maximum Load

• 1 A @ 24 VAC per output

Série PRO 1000 / 2000

Thermostats programmables et non programmables

Le présen t gu id e porte s ur les modèles su ivants :

Thermostats non programmables

TH 00D, TH 0D et TH 2 0D Thermostats programmables

TH2 0D et TH22 0D

(Ret rer le thermostat de sa plaque murale pour trouver le numéro de modèle.)

Typ es de systèm e

TH 1 11 0 D et T H211 0 D :

• Chauffage central - fourna se au gaz, mazout,

électr que ou à haut rendement (1 H)

• Chauffage central (vo r c -dessus) avec

cl mat sat on (1H/1C)

• Eau chaude (vapeur ou grav té) avec ou sans

pompe

• Cl mat seur central

• Systèmes de chauffage 750 mV

• Thermopompes sans chauffage d'appo nt

(1H1C)

T H 1 2 1 0 D et T H 2 2 10 D :

• Thermopompes avec chauffage d'appo nt

(2H1C)

T H110 0 D :

• Chauffage central - fourna se au gaz, mazout,

électr que ou à haut rendement (1 H)

• Eau chaude (vapeur ou grav té) avec ou sans

pompe

• Systèmes de chauffage 750 mV

Doit être installé par un technicien d’expérience ayant reçu la formation pertinente.

L re attent vement les nstruct ons. Le fa t de ne pas les su vre

r sque d’endommager le produ t ou de présenter un danger.

Besoin d’aide?

Pour obtenr de l'assstance au sujet de ce produt, consulter le http://yourhome.honeywell.com

ou téléphoner sans fra s au Centre de servce à la clentèle de Honeywell au 800 468- 502.

FRANÇAIS

Guide d’utilisation

Installation de la plaque murale

MISE EN GARDE : RISQUE DE CHOC ÉLECTRIQUE

Peut provoquer des chocs électr ques ou endommager le matér el. Couper

l'al mentat on électr que avant d'effectuer le raccordement.

1 Desserrer la v s de blocage au bas du thermostat. Noter que la v s est capt ve et ne

peut pas être enlevée de la plaque murale.

2 Séparer le thermostat de la plaque murale selon la f gure 1.

3 Placer la plaque murale contre le mur et marquer au crayon l'emplacement des trous.

NOTA : La mise à niveau est purement esthétique et n'aura aucun effet sur le

fonctionnement du thermostat.

4 Percer les trous aux endro ts marqués et nsérer les chev lles d'ancrage fourn es.

5 Passer les f ls par la grande ouverture s tuée au centre nfér eur de la plaque murale

selon la f gure 2.

6 F xer la plaque murale au mur avec les v s de montage fourn es selon la f gure 3.

7 Rel er les f ls aux bornes.

Figure

AVIS SUR LE MERCURE

S le nouveau thermostat remplace un anc en régulateur contenant un

contact à mercure, ne pas jeter l'anc en régulateur à la poubelle.

Commun quer avec le serv ce local de cue llette des déchets pour obten r

de l' nformat on sur le recyclage ou sur la bonne façon de se débarrasser

d'un anc en régulateur contenant un contact à mercure.

Andere Handbücher für PRO 1000

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Honeywell Thermostat Handbücher

Honeywell

Honeywell CM900 Bedienungsanleitung

Honeywell

Honeywell DT92A Kurzanleitung

Honeywell

Honeywell FocusPRO Wi-Fi TH6000 Series Bedienungsanleitung

Honeywell

Honeywell CT3200 series Bedienungsanleitung

Honeywell

Honeywell CT40A Bedienungsanleitung

Honeywell

Honeywell RTH9580 Wi-Fi Bedienungsanleitung

Honeywell

Honeywell TL8100A1008 - Line Voltage Thermostat Bedienungsanleitung

Honeywell

Honeywell lyric round Bedienungsanleitung

Honeywell

Honeywell RTHL3550 Bedienungsanleitung

Honeywell

Honeywell INNCOM e7w Bedienungsanleitung

Honeywell

Honeywell Prestige 2.0 THX9421 Bedienungsanleitung

Honeywell

Honeywell T4 Pro Bedienungsanleitung

Honeywell

Honeywell Lyric Round TH8732WFH-5002/U Bedienungsanleitung

Honeywell

Honeywell FocusPRO TH6220D Bedienungsanleitung

Honeywell

Honeywell RTH230B - 5-2 Day Programmable Thermostat Bedienungsanleitung

Honeywell

Honeywell TH8320WF01 Bedienungsanleitung

Honeywell

Honeywell RTH7460D1018/E 5-1-1 Bedienungsanleitung

Honeywell

Honeywell CM61 Bedienungsanleitung

Honeywell

Honeywell TB7300A5014B Bedienungsanleitung

Honeywell

Honeywell TH6220WF2 Bedienungsanleitung

Honeywell

Honeywell ZSTAT Installationshandbuch

Honeywell

Honeywell TP970 Series Gebrauchs- und Pflegehandbuch

Honeywell

Honeywell RTH2310 Bedienungsanleitung

Honeywell

Honeywell Q539A Bedienungsanleitung

Beliebte Thermostat Handbücher anderer Marken

EWELLY

EWELLY EW-181 Bedienungsanleitung

Prolon

Prolon T1100 Montageanleitung

Computherm

Computherm Q20 Bedienungsanleitung

Heatmiser

Heatmiser neoStat Bedienungsanleitung

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat Bedienungsanleitung

Saswell

Saswell SAS920XWHB-7-S-RF Leitfaden

Aircalo

Aircalo TFP1-ET85P2 Bedienungsanleitung

Carrier

Carrier DEBONAIR 33CS Bedienungsanleitung

Lennox

Lennox iHarmony Zone Thermostat Montageanleitung

Gemtech

Gemtech GT7000 Bedienungsanleitung

Rollei

Rollei Smartes 45000 Bedienungsanleitung

Sinope

Sinope TH1300RF Bedienungsanleitung

NuTone

NuTone NTBZ48 Original Betriebsanleitung

Stelpro

Stelpro MAESTRO ASMT402AD Bedienungsanleitung

Aube Technologies

Aube Technologies TH305 Bedienungsanleitung

Powtier Controls

Powtier Controls 505MST Bedienungsanleitung

Kanmor

Kanmor Zone Control 369e Bedienungsanleitung

MICROclimate International

MICROclimate International B2 Magic Eye Bedienungsanleitung