Honeywell PRO TH3210D Bedienungsanleitung

Installation

Guide

TH3210D

Non-programmable Digital Thermostat

Product Application

This thermostat provides electronic control of 24 VAC heat pump systems with aux-

iliary heat (2 heat/1 cool).

Power Type

• Battery power

• Common wire

• Common wire with battery backup

System Settings

• Heat, Off, Cool, Em Heat

Fan Settings

• Auto, On

Must be installed by a trained, experienced technician

• Read these instructions carefully. Failure to follow these instructions can dam-

age the product or cause a hazardous condition.

• Check the ratings in this booklet to verify that this product is suitable for your

application (see page 11).

• Always test for proper operation after installation (see pages 7-8).

CAUTION: ELECTRICAL HAZARD

Can cause electrical shock or equipment damage. Disconnect power before

beginning installation.

MERCURY NOTICE

If this product is replacing a control that contains mercury in a sealed tube, do not

place the old control in the trash. Contact your local waste management authority for

instructions regarding recycling and proper disposal.

® U.S. Registered Trademark. Patents pending.

PRO TH3210D Non-programmable Digital Thermostat

Install the thermostat about 5 feet (1.5m) above the floor in an area

with good air circulation at average temperature.

Do not install in locations where the thermostat can be affected by:

• Drafts or dead spots behind doors and in corners

• Hot or cold air from ducts

• Sunlight or radiant heat from appliances

• Concealed pipes or chimneys

• Unheated/uncooled areas such as an outside wall behind the thermostat

NO NO

Table of contents

Installation tips

IInnssttaallllaattiioonn

Pre-installation checklist ................2

Wallplate installation ......................3

Wiring..............................................4

Wiring diagrams ..............................5

IInnssttaalllleerrSSeettuupp

Battery installation ..........................6

Thermostat mounting ....................6

Installer setup..................................7

Installer system test ........................7

AAppppeennddiicceess

Quick reference to controls............9

Quick reference to display..............9

Compressor protection ..................9

In case of difficulty ......................10

Accessories....................................11

Specifications ................................11

Installation Guide

Pre-installation checklist

Package contents

Check to make sure your package includes the following items:

• PRO TH3210D digital thermostat (wallplate attached to back)

• Operating manual

• Wall anchors and mounting screws (2 each)

• AA alkaline batteries (2)

Required tools & supplies

• No. 2 Phillips screwdriver

• Small pocket screwdriver

• Drill

• Drill bit (3/16” for drywall, 7/32” for plaster)

• Hammer

• Pencil

• Electrical tape

• Level (optional)

PRO TH3210D Non-programmable Digital Thermostat

Remove the wallplate from the ther-

mostat as shown at left, then follow

directions below for mounting.

1 Pull wires through wire hole.

2 Position wallplate on wall, level and

mark hole positions with pencil.

3 Drill holes at marked positions as

shown below, then tap in

supplied wall anchors.

4 Place wallplate over anchors, insert

and tighten mounting screws.

Grasp top and bottom of wallplate

and pull to remove from thermostat.

Drill 3/16” holes for drywall.

Drill 7/32” holes for plaster.

Wall anchors

Mounting screwsWire hole

Wallplate installation

Installation Guide

Wiring

1 Loosen screw terminals, insert

wires into terminal block, then re-

tighten screws.

2 Push excess wire back into the

wall opening. Keep wires in shaded

area as shown at left.

3 Plug the wall opening with non-

flammable insulation to prevent

drafts from affecting thermostat

operation.

Terminal Designations

EEEmergency heat relay.

AAuuxxAuxiliary heat relay.

YYCompressor contactor.

GGFan relay.

OOHeat pump changeover valve

energized in cooling.

LLHeat pump reset.

RRPower wire from secondary

side of system transformer.

BBHeat pump changeover valve

energized in heating.

CCCommon wire from secondary

side of system transformer.

Terminal

block

NOTES

C terminal

The C (common wire) terminal is optional

when thermostat is powered by batteries.

L terminal

Heat pump reset. L terminal is powered con-

tinuously when thermostat is set to Em Heat.

Wire specifications

Use 18- to 22-gauge thermostat wire.

Shielded cable is not required.

Keep wires in this

shaded area

CAUTION: ELECTRICAL HAZARD. Can cause electrical shock or equipment damage.

Disconnect power before wiring.

Wiring

PRO TH3210D Non-programmable Digital Thermostat

1Power supply. Provide disconnect means and overload protection as required.

2Optional 24 VAC common connection.

3Use either Oor Bterminals for changeover valve.

4L terminal is powered continuously when thermostat is set to Em Heat.

5Install field jumper between E and Aux if there is no emergency heat relay.

Wiring diagram

Installation Guide

AC Power

The thermostat can be powered by 24

VAC power, or by batteries.

To wire the thermostat for AC power,

connect the common side of the

transformer to the “C” terminal as

shown at left.

Connect common

side of transformer

to “C” terminal

Install batteries in back of thermostat

(optional if AC powered).

Battery Power

The thermostat can be powered by

batteries alone or, if used with AC

power, can provide backup power to

the display during power interruptions.

To Mount Thermostat

Align the 4 tabs on the wallplate with

corresponding slots on the back of the

thermostat, then push gently until the

thermostat snaps in place.

Power options & mounting

PRO TH3210D Non-programmable Digital Thermostat

Auxiliary heat

cycle rate (CPH)

Emergency heat

cycle rate (CPH)

Compressor

cycle rate (CPH)

Temperature

display

Compressor

protection

5 For gas or oil furnaces of less than 90% efficiency

1 For steam or gravity systems

3 For hot water systems & furnaces of over 90% efficiency

9 For electric furnaces

[Other cycle rate options: 2, 4, 6, 7, 8, 10, 11 or 12 CPH]

9 For electric furnaces

1 For steam or gravity systems

3 For hot water systems & furnaces of over 90% efficiency

5 For gas or oil furnaces of less than 90% efficiency

[Other cycle rate options: 2, 4, 6, 7, 8, 10, 11 or 12 CPH]

3 Recommended for most compressors

[Other cycle rate options: 1, 2, 4, 5 or 6 CPH]

0 Fahrenheit

1 Celsius

5 Five-minute compressor off time **See page 9

[Other options: 0, 1, 2, 3 or 4-minute off time]

Setup Function Settings & Options

To begin, press and hold the and

buttons until the display changes

Function

number

Press to change settings

Press to advance to next function

Press and hold to exit and save settings

Setting

Installer setup

Follow the procedure below to configure the thermostat to match the installed

heating/cooling system, and customize feature operation as desired.

Setup

Installer system test

After completing the installer setup above, press the button again to begin a

system test (see next page).

Press and hold both buttons

Installation Guide

10 0

Test

Heating system

Emergency heat

Cooling system

Thermostat

information

(for reference only)

0 Compressor and fan turn off.

1 Compressor and fan turn on.

2 Auxiliary heat turns on.

0 Heat and fan turn off.

1 Heat and fan turn on.

2 Auxiliary heat turns on.

0 Compressor and fan turn off.

1 Compressor and fan turn on.

71 Software revision number (major revisions)

72 Software revision number (minor revisions)

73 Configuration identification code (major)

74 Configuration identification code (minor)

75 Production configuration date code (week)

76 Production configuration date code (year)

System Test System Status

Installer system test

CAUTION: EQUIPMENT DAMAGE HAZARD

Compressor protection (minimum off time) is bypassed during testing. To prevent

equipment damage, avoid cycling the compressor quickly.

System switch

System test

number

System status

Follow the procedure below to test the heating and cooling system.

1 Set SSYYSSTTEEMMswitch to Heat.

2 Press to turn on and check systems (see table, below).

3 Press until systems turn off.

4 Set SSYYSSTTEEMMswitch to Em Heat and repeat steps 2-3 above.

5 Set SSYYSSTTEEMMswitch to Cool and repeat steps 2-3 above.

5Press and hold to terminate test at any time.

Andere Handbücher für PRO TH3210D

Inhaltsverzeichnis

Andere Honeywell Thermostat Handbücher

Honeywell

Honeywell T4360G Bedienungsanleitung

Honeywell

Honeywell T8600 Bedienungsanleitung

Honeywell

Honeywell RTH5100B Bedienungsanleitung

Honeywell

Honeywell T8601D Bedienungsanleitung

Honeywell

Honeywell T8602C Bedienungsanleitung

Honeywell

Honeywell VisionPRO Series Bedienungsanleitung

Honeywell

Honeywell TH9320WFV Bedienungsanleitung

Honeywell

Honeywell T8665A Chronotherm IV Bedienungsanleitung

Honeywell

Honeywell T8611C Bedienungsanleitung

Honeywell

Honeywell Digital Round T8775C Bedienungsanleitung

Honeywell

Honeywell FocusPRO TH6220D Bedienungsanleitung

Honeywell

Honeywell TB7200 Series Benutzerhandbuch

Honeywell

Honeywell ADEMCO 4500 Bedienungsanleitung

Honeywell

Honeywell CT3400 Bedienungsanleitung

Honeywell

Honeywell RTH2300 series Bedienungsanleitung

Honeywell

Honeywell TH5220D1003 - Digital Thermostat, 2h Bedienungsanleitung

Honeywell

Honeywell Digital Round T8775A Bedienungsanleitung

Honeywell

Honeywell CHRONOTHERM IV DELUXE T8624D Bedienungsanleitung

Honeywell

Honeywell SuperStat Bedienungsanleitung

Honeywell

Honeywell RTH7500 Series Bedienungsanleitung

Honeywell

Honeywell WebStat T7350 Bedienungsanleitung

Honeywell

Honeywell TB7220 COMMERCIALPRO Bedienungsanleitung

Honeywell

Honeywell T10 Pro Smart Bedienungsanleitung

Honeywell

Honeywell PRO 1000 Bedienungsanleitung

Beliebte Thermostat Handbücher anderer Marken

EWELLY

EWELLY EW-181 Bedienungsanleitung

Prolon

Prolon T1100 Montageanleitung

Computherm

Computherm Q20 Bedienungsanleitung

Heatmiser

Heatmiser neoStat Bedienungsanleitung

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat Bedienungsanleitung

Saswell

Saswell SAS920XWHB-7-S-RF Leitfaden

Aircalo

Aircalo TFP1-ET85P2 Bedienungsanleitung

Carrier

Carrier DEBONAIR 33CS Bedienungsanleitung

Lennox

Lennox iHarmony Zone Thermostat Montageanleitung

Gemtech

Gemtech GT7000 Bedienungsanleitung

Rollei

Rollei Smartes 45000 Bedienungsanleitung

Sinope

Sinope TH1300RF Bedienungsanleitung

NuTone

NuTone NTBZ48 Original Betriebsanleitung

Stelpro

Stelpro MAESTRO ASMT402AD Bedienungsanleitung

Aube Technologies

Aube Technologies TH305 Bedienungsanleitung

Powtier Controls

Powtier Controls 505MST Bedienungsanleitung

Kanmor

Kanmor Zone Control 369e Bedienungsanleitung

MICROclimate International

MICROclimate International B2 Magic Eye Bedienungsanleitung