Hoover SteamVac F5835-900 Betriebsanleitung

SERVICE INSTRUCTIONS

CARPET CLEANING MACHINE

STEAM VAC

Maytag Services

16025867

RECOVERYTANK HANDLE

ASSEMBLY-'_

CORD

ASSEMBLY

CARPET

GROOMER

BRUSH

MOTOR

COVER

ASSEMBLY

RESERVOIR

ASSEMBLY

LOWER

HANDLE

ASSEMBLY

HANDLE

RELEASE

LEVER '_

L.H. TRUNION

PUMP DUC ./_j,_T,_'_ ON/OFF SWITCH

WHEEL

"E" CLIP

WASHER

WHEEL SHAFT

STANDPIPE GASKET

MAIN BODY

1. General

The steam vac is a self contained domestic extractor

designed for deep cleaning of carpet and rugs.

Initial models incorporate six and seven amp motors.

Top of the line models include a tool kit which allows

the unit to be used for stair or upholstery cleaning.

This instruction deals with the top of the line models.

Instructions that pertain only to low end models will be

noted,

II. Operation

The units are controlled by the on/off pedal located on

the LH side,

ON/OFF

PEDAL

Solution is gravity fed to the floor from the solution

tank through the reservoir assembly to the distributor,

The reservoir assembly is opened by actuating the

trigger in the handle.

Suction is directed to the floor through the clear

nozzle and up into the recovery tank where the air

and water are separated. A float prevents the

recovery tank from being overfitled.

The turbine (air) pump operates on the suction from

the motor. Suction is directed to the pump through

the pump duct, and is completed when the door on

the hood is opened.

The Pump gets a constant flow of solution from the

solution tank through the reservoir assembly. On

models without the pump, the pump tap on the

reservoir is plugged.

The recovery tank can be unlatched and carried to

empty.

The toot set can be used by removing the tank duct

and replacing with the hose assembly. Open tool

door and connect hose. This will direct solution and

suction to the hose grip.

III. Disassembly

A. Solution tank

To remove, unlatch and pull tank assembly

out of position. (Fig. 1)

HANDLE

Fig. 1

Replaceable components of the tank assembly

include the cap assembly, cap gasket and poppet

valve.

B Cap assembly

1. Twist off to remove. (Fig. 2)

Fig. 2

2. Slide gasket off to replace. (Rib on gasket faces

toward cap.)

C. Poppet valve

1. Insert screwdriver through tank opening

and push valve until it snaps out of seat. (Fig. 3)

Fig. 3

2. Work valve stem out of tank from underneath.

3. The spring, brass washer and valve seat will stay

trapped in the valve seat. Remove through tank

opening.

Note positioning in Fig. 3A.

SPRING-._/_

WASHERT_ _'

VALVE SEAL'_t_

Fig. 3A VALVE STEM "'_ ._

The cupped end of the valve seal faces downward

upon reassembly.

To reassemble valve:

1. Slide valve assembly into valve seat through

opening in bottom of tank. (Fig. 4) Use a small

amount of soap on seal to case assembly.

2. With small screwdriver, work rubber washer into

With £mnll £nr#wttrivnr wnrk rllhh#r

housing. (Fig. 5)

3. Continue to slide shaft in until it stops.

Fig. 5

4. Valve should spring open and closed when

fully seated.

D. Upper handle assembly

1. Remove two bolts and slide handle off. (Fig. 6)

Fig. 6

The. handle i.qr_.nlaep.d a._ an a._._.mhlv

The handle is replaced as an assembly.

If the upper handle rod becomes dislodged during

disassembly, reposition it with the large fin towards

the front of the handle. (Fig. 7)

Fig. 7

_ LARGE FIN

TOWARDS

FRONT

Slide it up into the handle until it snaps into position.

E. Recovery tank

1. Release handle to lowest position (RH side pedal)

2. Pivot two latches outward (Fig. 8) and lift off tank.

LATCH

Fig. 8

3. Remove lid assembly. (Fig. 9)

The lid is carried in service as an assembly that

includes the lid, float retainer, float and filter.

F. Recovery tank duct

1. Slide out of position. (Fig. 10)

Fig.

FRONT

PANEL

G. Hood assembly

1. Remove screw - located below recovery tank at

top rear of hood. (Fig. 11)

Fig. 11

2. Carefully pry inward on rear panels of hood to

release snaps. (Fig. 12)

Fig. 12

1. Lift hood until it clears latches and push forward to

remove.

H. Nozzle front plate /seal

The nozzle front plate is stocked as a part of the hood

assembly.

It is not recommended the front plate be removed.

This could damage or misposition the seal which is

critical to the machine's performance.

I. Door assembly

1. Open door and pry outward on either side

to release one pin and remove. (Fig. 14)

The door is replaced as an assembly (door, seal and

speed nut).

J. Door spring

1. Positioned on hood boss per illustration in

Fig. 15.

Fig. 15

To reassemble hood.

1. Position two locating tabs in front corners into

mating boss on base and pivot hood down into

position until the sides of the hoods snap into

retaining bosses.

2. Replace screw and tighten.

K. Pump assembly (where applicable)

1. Remove screw. (Fig. 16)

Fig. 16

Disconnect tubing coming from handle assembly.

Release snap and lift pump out. (Fig. 17)

Pumpisreplacedasan assemblywhichincludesthe

quickconnectandtubing.(Fig. 18)

Fig. 18

The quick connect is also available as a separate

service item.

L. Pump duct

The pump duct is held by the pump mounting screw.

(Fig. 19)

Fig. 19

M. Motor cover assembly

DISTRIBUTOR

HOSE

Fig. 20

_ MOTOR

COVER

ASSEMBLY

1. Disconnect hose to distributor.

2. Remove five screws (Fig. 21) and lift off.

On pump models, if pump is removed, screw

five will already be out.

Themotorcoverassemblyconsistsoftherecovery

tanklatchesanddistributor.

To remove distributor.

1. Push outward on distributor stem while pulling out

and down on 'T' boss. Distributor will snap out of

housing. (Fig. 22)

N. Handle release, switch lever and switch

Lower the handle to lowest position.

1. Remove trunnions - two screws in each.

(Fig. 23)

2. Unclip cord from cord clip in rear of handle.

MOUNTING

SCREWS

TRUNNION

1 I

Fig. 23

3. Lift lower handle out of position.

Handle release lever

The RH trunnion traps the handle release lever. Slide

lever inward then up to remove. (Fig. 24)

\ ',

Fig. 24

Switch /switch pedal

1. The LH trunnion houses the on/off switch and

traps the switch lever. (Fig. 25)

TRUNNION

ON/OFF

SWITCH

LEVER

Fig. 25

2. Disconnect leads and snap switch out of trunnion.

3. The switch pedal can be removed once

the trunnion is lifted.

0. Cord

With motor cover removed cord can be accessed

1. Disconnectleadsatswitch,insulatedterminaland

groundscrew.

2. Disconnectcordfromcordclipinbackof handle.

3. Snapstrainreliefoutofhousing.

Note: Uponreassembly,routecordasshownin Fig.

26. Alsoit isvery important toreconnectground

lead.

GROUND

RELIEF

Fig. 26

P. Lower handle

1. Replaceable parts of the lower handle

include the handle cover, lower rod, reservoir

assembly and lower handle. (Fig. 27)

LOWER HANDLE_

LOWER

ROD

RESERVOIR

ASSEMBLY

Fig. 27

HANDLE

COVER

0. Handle cover

1. Release four snaps and lift cover off. (Fig.

28 A & B)

Fig. 28A

Fig. 28B

R. Lower rod

1. Trapped in place by handle cover. Lift out

to remove. (Fig. 29)

Fig. 29 :7,

S. Reservoir assembly

1. Release two clips and remove from cradle

in lower handle. (Fig. 30)

The reservoir is replaced as an assembly which does

not include tubing.

The reservoir assembly can be inspected by removing

the diaphragm valve and checking the chamber and

valve. (Fig. 31)

Pull here

with

to remove

Fig. 31

Tubing routing is illustrated in Fig. 32.

Note: 900 coupler in pump tubing protects tubing

from kinking. Tubing is available in a service kit that

includes the tubing and 900 coupler. Pump tubing is

3/8' ID. All other is 1/4" 1 D.

Fig. 32

T. Motor

With motor cover removed disconnect leads and lift

motor out of main body.

The motor is replaced as an assembly only.

Andere Handbücher für SteamVac F5835-900

Dieses Handbuch passt für folgende Modelle

Andere Hoover Staubsauger Handbücher

Hoover

Hoover WindTunnel WindTunnel vacuum cleaner Bedienungsanleitung

Hoover

Hoover ZOOM Bedienungsanleitung

Hoover

Hoover Presto 2-in-1 Bedienungsanleitung

Hoover

Hoover UH70085 - Pet Cyclonic Bagless Upright... Bedienungsanleitung

Hoover

Hoover S3590 - Duros Power Nozzle Canister Vacuum... Bedienungsanleitung

Hoover

Hoover Power Swift Bedienungsanleitung

Hoover

Hoover U6630900 - Self Propelled WindTunnel Bagless Upright... Bedienungsanleitung

Hoover

Hoover U5473 Bedienungsanleitung

Hoover

Hoover U5467900 Bedienungsanleitung

Hoover

Hoover H-ENERGY 700 Bedienungsanleitung

Hoover

Hoover CHORUS Bedienungsanleitung

Hoover

Hoover POWER PATH PRO Bedienungsanleitung

Hoover

Hoover WHIRLWIND EVO Bedienungsanleitung

Hoover

Hoover UH40145B Bedienungsanleitung

Hoover

Hoover Power Capsule Bedienungsanleitung

Hoover

Hoover SmartWash+ FH53000PC Betriebsanleitung

Hoover

Hoover 9011PH Regal Bedienungsanleitung

Hoover

Hoover Space Explorer series Bedienungsanleitung

Hoover

Hoover Elite Supreme S1211 Bedienungsanleitung

Hoover

Hoover RA22AFG Bedienungsanleitung

Hoover

Hoover FH50 Bedienungsanleitung

Hoover

Hoover Breeze BR40PET Bedienungsanleitung

Hoover

Hoover BH70600 Series Bedienungsanleitung

Hoover

Hoover Soft Guard C1404 Bedienungsanleitung

Beliebte Staubsauger Handbücher anderer Marken

Bissell

Bissell LittleGreen Proheat 1425 Series Bedienungsanleitung

Panasonic

Panasonic MC-YL637S147-AE Bedienungsanleitung

LG A9 Series Bedienungsanleitung

Oreck

Oreck Cordless Captura BK51700 Series Bedienungsanleitung

Kogan

Kogan KAVACROBVWA Bedienungsanleitung

Kränzle

Kränzle VENTOS 50 ID Benutzerhandbuch

NEFF

NEFF N17XH10 0 Series Bedienungsanleitung

EVVO

EVVO Ai35 Bedienungsanleitung

DeWalt

DeWalt DWH200D Bedienungsanleitung

Pontec

Pontec Pondomatic Vacuum Cleaner Bedienungsanleitung

Cleanmaxx

Cleanmaxx PC-P007E Bedienungsanleitung

RIDGID

RIDGID WD1685AU0 Bedienungsanleitung

Ezviz

Ezviz RE4P Bedienungsanleitung

STG global

STG global TANVAC HDV3000 Bedienungsanleitung

Shark

Shark ROTATOR PRO COMPLETE NV550 Series Bedienungsanleitung

Factory

Factory M3340 Bedienungsanleitung

Shop-Vac

Shop-Vac VN92 SERIES Bedienungsanleitung

Nobles

Nobles 608669 Produkthandbuch