Horizon Hobby E-flite Carbon-Z Cub SS Bedienungsanleitung

Instruction Manual

Bedienungsanleitung

Manuel d’utilisation

Manuale di Istruzioni

Carbon-Z®Cub SS

SAFE®Select Technology, Optional Flight Envelope Protection

Carbon-Z Cub SS

Safety Precautions and Warnings

NOTICE

All instructions, warranties and other collateral documents are subject to change at the sole discretion of Horizon Hobby, LLC. For up-to-date product literature, visit

horizonhobby.com or towerhobbies.com and click on the support or resources tab for this product.

14+ AGE RECOMMENDATION: Not for children under 14 years. This is not a toy.

MEANING OF SPECIAL LANGUAGE:

The following terms are used throughout the product literature to indicate various levels of potential harm when operating this product:

WARNING: Procedures, which if not properly followed, create the probability of property damage, collateral damage, and serious injury OR create a high probability of

supercial injury.

CAUTION: Procedures, which if not properly followed, create the probability of physical property damage AND a possibility of serious injury.

NOTICE: Procedures, which if not properly followed, create a possibility of physical property damage AND little or no possibility of injury.

WARNING: Read the ENTIRE instruction manual to become familiar with the features of the product before operating. Failure to operate the product correctly can

result in damage to the product, personal property and cause serious injury.

This is a sophisticated hobby product. It must be operated with caution and common sense and requires some basic mechanical ability. Failure to operate this Product

in a safe and responsible manner could result in injury or damage to the product or other property. This product is not intended for use by children without direct adult

supervision. Do not use with incompatible components or alter this product in any way outside of the instructions provided by Horizon Hobby, LLC. This manual contains

instructions for safety, operation and maintenance. It is essential to read and follow all the instructions and warnings in the manual, prior to assembly, setup or use, in

order to operate correctly and avoid damage or serious injury.

As the user of this product, you are solely responsible for operating in a manner that does not endanger yourself and others or result in damage to the product or the property of others.

• Always keep a safe distance in all directions around your model to avoid

collisions or injury. This model is controlled by a radio signal subject to

interference from many sources outside your control. Interference can cause

momentary loss of control.

• Always operate your model in open spaces away from full-size vehicles, trafc

and people.

• Always carefully follow the directions and warnings for this and any optional

support equipment (chargers, rechargeable battery packs, etc.).

• Always keep all chemicals, small parts and anything electrical out of the reach

of children.

• Always avoid water exposure to all equipment not specically designed and

protected for this purpose. Moisture causes damage to electronics.

• Never place any portion of the model in your mouth as it could cause serious

injury or even death.

• Never operate your model with low transmitter batteries.

• Always keep aircraft in sight and under control.

• Always use fully charged batteries.

• Always keep transmitter powered on while aircraft is powered.

• Always remove batteries before disassembly.

• Always keep moving parts clean.

• Always keep parts dry.

• Always let parts cool after use before touching.

• Always remove batteries after use.

• Always ensure failsafe is properly set before ying.

• Never operate aircraft with damaged wiring.

• Never touch moving parts.

WARNING AGAINST COUNTERFEIT PRODUCTS: If you ever need to replace your Spektrum receiver found in a Horizon Hobby product, always purchase from

Horizon Hobby, LLC or a Horizon Hobby authorized dealer to ensure authentic high-quality Spektrum product. Horizon Hobby, LLC disclaims all support and

warranty with regards, but not limited to, compatibility and performance of counterfeit products or products claiming compatibility with DSM or Spektrum technology.

Box Contents

Table of Contents

Specications

56.3 in (1430mm)

84.6 in (2100mm)

8.15-9.48 lb

(3.69-4.30 kg)

If you own this product, you may be required to register with the FAA. For up-to-date information on how to register with the FAA, please visit

https://registermyuas.faa.gov/. For additional assistance on regulations and guidance on UAS usage, visit knowbeforeyouy.org/.

Preight....................................................................................................4

Model Assembly .......................................................................................5

PNP Receiver Selection and Installation ..................................................11

Battery Installation and ESC Arming........................................................12

SAFE®Select Switch Designation ...........................................................14

Smart Technology™ Telemetry...............................................................14

Control Surface Centering and Adjusting a Ball Link................................15

Control Direction Test..............................................................................15

Center of Gravity (CG) .............................................................................16

Control Horn and Servo Arm Settings......................................................16

In Flight Trimming...................................................................................16

Flying Tips and Repairs...........................................................................17

Post Flight ..............................................................................................18

Optional Tow Release Installation............................................................18

Troubleshooting Guide AS3X ...................................................................20

Troubleshooting Guide ............................................................................20

Replacement Parts..................................................................................21

Recommended Parts...............................................................................21

Optional Parts.........................................................................................21

AMA National Model Aircraft Safety Code................................................22

Limited Warranty ....................................................................................22

Warranty and Service Contact Information ..............................................23

FCC Information......................................................................................23

IC Information.........................................................................................23

Compliance Information for the European Union......................................23

Tools Required

• 1.5mm Hex wrench

• 2mm Hex wrench

• 2.5mm Hex wrench

• 4mm Wrench /Socket

• Needle nose pliers

• Adjustable wrench

Quick Start Information

Transmitter Setup

1. Blank (Acro) Model

2. Wing Type: 1 Aileron, 1 Flap

3. Servo Reversing: Gear Reversed, All Others Normal

4. Travel Adjust (All Surfaces): 100%

Dual Rates*

High Rate Low Rate

Aileron p= 50mm

q= 45mm

p= 35mm

q= 30mm

Elevator p= 42mm

q= 42mm

p= 30mm

q= 30mm

Rudder = 65mm

= 65mm

= 50mm

= 50mm

Flap Travel Take-off q= 20mm Landing q= 35mm

EXPO

(Soft center)

High Rate Low Rate

Aileron 10% 5%

Elevator 10% 5%

Rudder 10% 5%

Center of Gravity (CG) 105-120mm back from the leading edge, measured

at the wing root

Flight Timer Setting 4 minutes

Motor:

BL50-525Kv

(EFLM7450)

Included Included

ESC: Avian 60-Amp Smart ESC (SPMXAE1060B) Installed Installed

Servos: (4) 26g Digital MG Mini Servo (EFLR7145)

(2) 13g Digital MG Micro Servo (EFLR7155) Installed Installed

Receiver: Spektrum™ AR637TA 6-Channel AS3X/SAFE

Telemetry Receiver (SPMAR637T) Installed Required to

Complete

Recommended Battery: 4000mAh 22.2V 6S 50C Li-Po

(SPMX40006S50) Required to

Complete

Required to

Complete

Recommended Battery Charger:

6-cell Li-Po battery balancing charger

Required to

Complete

Required to

Complete

Recommended Transmitter:

Full-Range 2.4GHz with Spektrum™DSM2®/DSMX®

technology with programmable mixing and adjustable

dual rates

Required to

Complete

Required to

Complete

* The dual rates values given are intended for rst time pilots through intermediate

level pilots. For advanced settings options, see the Dual Rates and Control Throws

section of the manual.

Carbon-Z Cub SS

Preight

1 Remove and inspect contents.

2 Read this instruction manual thoroughly.

3 Charge the ight battery.

4 Fully assemble the aircraft.

5 Install the ight battery in the aircraft (once it has been fully charged).

6 Check the Center of Gravity (CG).

7 Bind the aircraft to your transmitter.

8 Make sure all linkages move freely.

9 Perform the control direction test with the transmitter.

10 Adjust the ight controls and transmitter as needed.

11 Perform a radio system range test.

12 Find a safe open area to y.

13 Plan ight for ying eld conditions.

Transmitter Setup (BNF)

IMPORTANT: After you set up your model, always rebind the transmitter and

receiver to set the desired failsafe positions.

If your transmitter allows it, enable the throttle cut feature. Always engage throttle

cut before approaching the aircraft.

Dual Rates

Low rate is recommended for the initial ights.

NOTICE: To ensure AS3X®technology functions properly, do not lower rate

values below 50%. If lower rates are desired, manually adjust the position of the

pushrods on the servo arm.

NOTICE: If oscillation occurs at high speed, refer to the Troubleshooting Guide for

more information.

Expo

After rst ights, you may adjust expo in your transmitter.

Computerized Transmitter Setup

(DX6i, DX6e‡, DX6‡, DX7, DX7S, DX8, DX9, DX10t, DX18, DX20, iX12. iX20,

NX6, NX8 and NX10)

Start all transmitter programming with a blank ACRO model (do a model reset),

then name the model.

Set Aileron, Eleva-

tor and Rudder Dual

Rates to:

HIGH 100%

LOW 70%

Set Servo Travel to: 100%

Set Throttle Cut to -130%

DX6i

1. Go to the SETUP LIST MENU

2. Set MODEL TYPE: ACRO

3. Go to ADJUST LIST MENU

4. Set FLAPS: Norm £100 Flap Elev 0

LAND 100 Flap Elev 15

DX7S

DX8

1. Go to the SYSTEM SETUP

2. Set MODEL TYPE: AIRPLANE

3. Set WING TYPE: 1 AIL 1 FLAP

4. Go to the FUNCTION LIST

5. Set FLAP SYSTEM: Choose Flap

NORM: 0% FLAP*

MID: 50% FLAP* 6% Elevator

LAND: 100% FLAP* 15% Elevator

SPEED 2.0S: SWITCH = FLAP

DX6e‡

DX6

(Gen2)‡

DX7

(Gen2)

DX8

(Gen2)

DX9

DX10t

DX18

DX20

iX12†

iX20†

NX6

NX8

NX10

1. Go to the SYSTEM SETUP (Model Utilities)†

2. Set MODEL TYPE: AIRPLANE

3. Set AIRCRAFT TYPE (Model Setup, Aircraft Type)†:

WING: 1 AIL 1 FLAP

4. Go to the FUNCTION LIST (Model Adjust)†

5. Set FLAP SYSTEM:

SELECT SWITCH D:

POS 0: 0% FLAP*

POS 1: 40% FLAP* 6% Elevator

POS 2: 100% FLAP* 15% Elevator

SPEED 2.0

†Some of the terminology and function locations used in the iX12, iX20

programming may be slightly different than other Spektrum AirWare™ radios.

The names given in parenthesis correspond to the iX12, iX20 programming

terminology. Consult your transmitter manual for specic information about

programming your transmitter.

* Flap programming values may vary slightly. For your initial ights use the

recommended ap travel settings provided in the Flaps section and adjust

the ap travel to your preference on subsequent ights.

Model Assembly

Landing Gear Installation

1. Install a tundra tire (A) on the strut (B) using 2 wheel collars (C) as shown.

Ensure the set screws (D) are aligned with the at spots on the strut. Apply

threadlock and tighten. Repeat tire installation for the opposite strut.

2. Insert the legs of the strut assembly into the landing gear brackets (E) located

on the bottom of the fuselage.

3. Align the holes of the strut legs with the holes of the landing gear bracket.

Secure the landing gear into place using 2 screws (F) and 2 nuts (G). Repeat

installation for opposite strut.

4. Connect both hooks (H) to the holes located on the strut behind the tire.

5. Align the bottom of the landing gear suspension spring (I) to the second hole

of the front landing bracket. Secure it into place with the screw (F) and nut (G).

Repeat installation for opposite strut.

Required Adhesives:

Thread Lock

(D) 2 x 3mm

Set Screw

Bag K

(F) 2 x 16mm

Button head hex machine

Bag B

(G) 2mm

Lock Nut

Bag C

(F) 2 x 16mm

Button head hex machine

Bag B

(G) 2mm

Lock Nut

Bag C

Bag K

Carbon-Z Cub SS

Model Assembly (Continued)

Rudder Installation

1. Slide the rudder’s CA hinges (A) into the hinge slots (B) of the vertical n.

2. Install the screw (C) in the rudder mount. Do not over tighten, the rudder should

move smoothly.

3. Rest the aircraft on its nose, holding the tail up so the thin CA (cyanoacrylate

adhesive) will ow into the slots.

4. Bend the hinges by turning the rudder left, then carefully apply thin CA to each

hinge in the right side of each slot. Repeat this process for the left side of the

rudder. Apply 4-5 drops on each hinge on each side.

5. Connect the ball link (D) to the rudder control horn’s middle hole (E) using a

screw (F) and nut (G). Ensure the rudder servo arm is in the correct position,

then adjust the ball link on the linkage to center the rudder.

Required Adhesives:

Thin CA

Button head hex self tapping

Bag D

(F) 1.5x10mm

Hex head machine

Bag E

(G) 2mm

Lock Nut

Bag C

Model Assembly (Continued)

Horizontal Tail Installation

1. Slide the horizontal stabilizer rod (A) into the hole in the rear of the fuselage.

2. Install the 2 piece (left and right) horizontal stabilizer as shown. Ensure the

control horn faces down.

3. Install 4 screws (B) in the front and rear holes in the bottom of the

horizontal tail.

4. Attach the ball link (C) to the elevator control horn’s middle hole using the

included nut (D) and screw (E).

5. Ensure the elevator servo arm is in the correct position, then adjust the linkage

to center the elevator.

When needed, disassemble in reverse order.

TIP: Use needle-nose pliers or ball link pliers (RVO1005) to remove or install a

link on a control horn.

(B) 3x12mm

Button head hex machine

Bag F

(D) 2mm

Lock Nut

Bag C

(E) 2x10mm

Hex head machine

Bag E

Carbon-Z Cub SS

Model Assembly (Continued)

Motor and Propeller Installation

1. Correctly align and connect the motor wire colors with the ESC wires.

2. Install the motor (A) with pre-installed X-mount (B) on the fuselage using 4

screws (C) and 4 lockwashers (D). Align the motor wires to face down and

position them in the pocket below the motor location. Ensure that the wires are

out of the way of the spinning motor.

3. Install the collet (E), and back plate (F) on the motor shaft (G).

4. Install the cowling (H) on the fuselage using 2 screws (I).

5. Install the spinner back plate (J), propeller (K) and nut (L) on the collet. Use a

tool to tighten the nut.

IMPORTANT: The propeller size numbers (15 x 7) must face out from the motor

for correct propeller operation. Ensure the nut holds the propeller tightly without

damaging the propeller.

6. Install the spinner (M) on the collet using the screw (N).

Disassemble in reverse order. Not all wiring shown.

NOTICE: If the propeller is not balanced, the aircraft may vibrate, causing the

stabilization system to not operate correctly and/or decrease the life

of the servos.

Horizon Hobby does not warrant replacement if the servos are used under

extreme vibration or the stabilization system is used with an unbalanced propeller.

For more information, view the propeller balancing video at

www.horizonhobby.com.

TIP: We recommend removal of the propeller before any radio system setup or

transport of your aircraft.

E G

(D) 3mm

Lock washer

Bag G

(N) 2.5x8mm

Pan head hex machine

Bag H

Hex head self tapping

Bag G

(I) 2.5x10mm

Button head hex self tapping

Bag D

Model Assembly (Continued)

Wing Installation

Before each ight, ensure all wing connectors and fasteners are secure.

Assemble both wings using the following steps. (Only the right wing shown)

1. Install 6 vortex generators (A) in the wing channels (B) by using the installed

double-sided tape.

2. Install the jury strut (D) on the wing mounts using 2 screws (E) and

2 lock nuts (F).

TIP: DO NOT overtighten lock nuts on the screws. Ensure the vertical brackets

can pivot freely on the wing mounts.

3. Install the wide front strut (G) on the front strut mounts using a screw (H) and

lock nut (F).

4. Install the narrow rear strut (J) on the rear strut mount using a screw (H) and

lock nut (F).

TIP: DO NOT overtighten lock nuts on the screws. Ensure the struts can pivot

freely in the strut mounts.

5. Attach the vertical bracket to the struts using 2 pins (I) and 2 R-clips (K). (E) 3 x 12mm

Button head hex machine

Bag F

(F) 3 mm

Lock Nut

Bag I

(H) 3 x 18mm

Button head hex machine

Bag J

(F) 3 mm

Lock Nut

Bag I

Bag L

(K)

Bag L

(I)

Carbon-Z Cub SS

AILE

FLAP

AILE

FLAP

Model Assembly (Continued)

Wing Installation (Continued)

1. Slide the wing tube (A) into the fuselage.

2. Install the left and right wing (Band C) onto the wing tube.

3. Connect the servo connectors (D) to the respective connectors on the fuselage

(connectors are marked AIL or FLAP) and slide the wing into the slot of the

fuselage.

NOTICE: Always put excess servo connector wire into the pocket of the wing to

prevent pinching of wires or other damage.

4. Secure the wings on the fuselage using 4 thumb screws (E) in the holes on the

top of the wings.

5. Install the 2 antenna (F) on top of the two rear thumb screws by pressing them

onto the thumb screw.

6. Connect the left and right wing struts to the fuselage mounts (G) using 4 pins

(H) and 4 R-clips (I).

Removal

We recommend removing the wings from the fuselage for storage or transport of

the aircraft.

TIP: Remove the jury strut pins and clips from the struts to pivot the brackets

and struts down to the wings. Wing struts do not need to be disassembled to be

removed.

NOTICE: Always secure loose parts after removal. DO NOT FLY if parts are

missing or damage may result.

(E) 3 x 25mm

Thumb Screw

Bag K

(F) Antenna Cap

Bag L

(H)

Bag L

(I)

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Horizon Hobby Spielzeug Handbücher

Horizon Hobby

Horizon Hobby Blade 120 S Bedienungsanleitung

Horizon Hobby

Horizon Hobby Blade SR UH-1 HUEY GUNSHIP Bedienungsanleitung

Horizon Hobby

Horizon Hobby E-flite AT-6 Bedienungsanleitung

Horizon Hobby

Horizon Hobby Beechcraft D18 1.5m Bedienungsanleitung

Horizon Hobby

Horizon Hobby Ultra-Micro P-51D Mustang BNF Bedienungsanleitung

Horizon Hobby

Horizon Hobby Blade CX4 Bedienungsanleitung

Horizon Hobby

Horizon Hobby Tower Hobbies Beaver 1.5m Bedienungsanleitung

Horizon Hobby

Horizon Hobby E-flite T-28 Trojan 1.2m EFL18350 Bedienungsanleitung

Horizon Hobby

Horizon Hobby E-FLITE Carbon-Z T-28 Bedienungsanleitung

Horizon Hobby

Horizon Hobby Alpha Patrol Boat Bedienungsanleitung

Horizon Hobby

Horizon Hobby Blade 70 S RTF Bedienungsanleitung

Horizon Hobby

Horizon Hobby UMX FPV RADIAN Bedienungsanleitung

Horizon Hobby

Horizon Hobby E-flite UMX Turbo Timber Evolution Bedienungsanleitung

Horizon Hobby

Horizon Hobby BLADE 150S Smart Bedienungsanleitung

Horizon Hobby

Horizon Hobby UMX B-25 Mitchell Bedienungsanleitung

Horizon Hobby

Horizon Hobby E-flite P-51D Mustang 1.5m Bedienungsanleitung

Horizon Hobby

Horizon Hobby EFL78500 Bedienungsanleitung

Horizon Hobby

Horizon Hobby ECX Temper ECX01015T1 Bedienungsanleitung

Horizon Hobby

Horizon Hobby Focke-Wulf 190A Bedienungsanleitung

Horizon Hobby

Horizon Hobby Ultra Micro F4U Corsair RTF/BNF Bedienungsanleitung

Horizon Hobby

Horizon Hobby Pawnee Brave Night Flyer AS3X Bedienungsanleitung

Horizon Hobby

Horizon Hobby F-18 Blue Angel Bedienungsanleitung

Horizon Hobby

Horizon Hobby UMX YAK 54 3D Bedienungsanleitung

Horizon Hobby

Horizon Hobby Hangar 9 Spitfire 60 ARF Bedienungsanleitung

Beliebte Spielzeug Handbücher anderer Marken

marklin

marklin 37321 Bedienungsanleitung

Canon

Canon PAPER CRAFT Bedienungsanleitung

GREAT PLANES

GREAT PLANES Pitts M-12S Bedienungsanleitung

NOCH

NOCH 14261 Bedienungsanleitung

Hausler

Hausler 450 SE V2 Bedienungsanleitung

Dynaflite

Dynaflite Daydream Bedienungsanleitung

Kenner

Kenner Batman 63651 Bedienungsanleitung

LEGO

LEGO 8527 Bedienungsanleitung

Multiplex

Multiplex EasyStar II Bedienungsanleitung

iKarus

iKarus ECO 8 Bedienungsanleitung

Walkera

Walkera 38 Bedienungsanleitung

Hasbro

Hasbro TRANSFORMERS BUMBLEBEE Bedienungsanleitung

MD MXION SWD Bedienungsanleitung

Mattel

Mattel Disney Pixar Cars Cozy Cone Spiral Rampway Bedienungsanleitung

marklin

marklin 39671 Bedienungsanleitung

LEGO

LEGO TECHNIC 8735 Bedienungsanleitung

Mattel

Mattel HOTWHEELS DWL04 Bedienungsanleitung

REVELL

REVELL Bristol Beaufighter TF.X Bedienungsanleitung