HP ProCurve MSM765zl Bedienungsanleitung

HP MSM765 zl Mobility Controller

Installation Guide

Abstract

This document describes how to install and initially configure the MSM765 zl Premium Mobility Controller (J9370A). This

product is hereafter referred to as controller. See also the MSM Controllers Configuration Guide.

HP Part Number: 5998-7937

Published: June 2015

Edition: 1

The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express

warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall

not be liable for technical or editorial errors or omissions contained herein.

Links to third-party websites take you outside the HP website. HP has no control over and is not responsible for information outside HP.com.

Acknowledgments

Microsoft® and Windows® are trademarks of the Microsoft group of companies.

Mozilla® and Firefox® are trademarks of the Mozilla Foundation.

Warranty

To obtain a copy of the warranty for this product, see the warranty information website:

www.hp.com/support/Networking-Warranties

Contents

1 Preparing for installation.............................................................................4

Identifying controller components................................................................................................4

Switch LEDs.............................................................................................................................5

Serial numbers.........................................................................................................................5

Installation precautions..............................................................................................................7

Environmental specifications.......................................................................................................7

Other documentation................................................................................................................7

2 Installing...................................................................................................8

Installation procedure................................................................................................................8

Verifying the controller is installed correctly..................................................................................9

3 Initially connecting and configuring............................................................10

Connect to the switch..............................................................................................................10

Activate the controller..............................................................................................................11

Install the product license key...................................................................................................12

Configure the switch for the controller........................................................................................12

Initial controller configuration...................................................................................................15

Restarting and resetting the controller........................................................................................18

4 Support and other resources......................................................................20

Online documentation.............................................................................................................20

Contacting HP........................................................................................................................20

HP websites...........................................................................................................................20

Typographic conventions.........................................................................................................20

A Replacing hardware components................................................................21

Replacing or removing a controller............................................................................................21

Replacing the disk drive...........................................................................................................21

Replacing the flash card..........................................................................................................22

B Uninstalling a License................................................................................24

Uninstalling a License..............................................................................................................24

Contents 3

1 Preparing for installation

The MSM765 zl Mobility Controller is a Services zl Module-based WLAN controller which plugs

into switches such as the 5400 zl and 8212 zl. New switches must be prepared according to their

documentation.

Identifying controller components

Front panel port and LEDs

Figure 1 Controller front panel

2 53 41

4. HDD Activity and Network Activity LEDs1. Module Status LED

5. USB port2. Module Locator LED

3. HDD Status and Compact Flash Status LEDs

•USB Port: This port is used to attach a USB device, such as a flash drive.

•The following table describes the LEDs on the front panel.

MeaningStateLED

Initialization was successful. Stays in this state when the

controller is booted to Service OS.

Flashing greenModule Status

(green/orange)

Controller is operational.On green

Error conditionFlashing/on orange

This LED is off by default.

Flashing cycle (green or orange) is 400ms on – 400ms off.

At boot, the Module Status, HDD Status, and CF Status LEDs

are green for ~2s, then orange for ~2s, then back to green

for ~1s, and finally all are turned off.

On during boot only when the controller is inserted into a

chassis, soft reboots do not enable this LED. Used to locate

Flashing/onModule Locator

(blue)

a specific module in an area full of chassis. Enabled by

using the following switch CLI command:

services <slot ID> locate <blink [duration]

| off | on [duration]>

This LED is off by default.

CF/HDD has initialized.On greenCF (Compact Flash)/HDD

Status (green/orange) CF/HDD is not detected.On orange

This LED is off by default.

4 Preparing for installation

MeaningStateLED

At boot, the Module Status, HDD Status, and CF Status LEDs

are green for ~2s, then orange for ~2s, then back to green

for ~1s, and finally all are turned off.

The drive is active.FlashingHDD Activity (green)

The drive is not active.Off

There is network activity on one or both internal ports.

If either ports fails, the controller status LED is set to flashing

orange.

FlashingNetwork Activity (green)

There is no network activity on either port.Off

Switch LEDs

The following figures show the Test, Fault, and Module Status LEDs on the switches in which the

controller can be installed.

Figure 2 Test, Fault, and Module Status LEDs on a Series 5400 zl switch

1 2 3

1. Fault LED

2. Test LED

3. Module Status LEDs

Figure 3 Test, Fault, and Module Status LEDs on a Series 8212 zl switch

1 2 3

1. Fault LED

2. Test LED

3. Module Status LEDs

Serial numbers

Serial numbers are required when contacting HP or a reseller for warranty assistance or for coverage

under a service agreement. For future reference, record the serial and product numbers in the

warranty booklet.

Switch LEDs 5

The controller ships as a bundle. From a warranty perspective, a bundle consists of two separate

hardware components:

•Controller

•Disk drive

See the provided warranty information for coverage details for each hardware component.

The disk drive serial number is found on its bottom.

Figure 4 Locating the disk drive serial number

1. Disk drive serial and product numbers (SN: SGxxxxxxxx)

The serial number for the controller is located on the back left corner of the controller. The serial

number of the controller can also be found in the management tool or through the CLI.

Figure 5 Locating the controller serial number

1. Controller serial number (SN: SGxxxxxxxx)

6 Preparing for installation

Installation precautions

•Static electricity can severely damage the electronic components on the controller. When

handling and installing the controller, follow these procedures to avoid damage from static

electricity:

•Handle the controller by its bulkhead or edges and avoid touching the components and

the circuitry on the board.

•When installing the controller, equalize any static charge difference between your body

and the switch by wearing a grounding wrist strap and attaching it to the switch's metal

body, or by frequently touching the switch's metal body.

•The controller has low-force, high-performance connectors. High insertion forces are not

necessary to install the controller, and should not be used.

•Ensure the controller is fully inserted. Press the controller into the slot until the bulkhead on the

controller contacts or is very close to contacting the front face of the switch chassis.

•When the controller is fully inserted, screw in the two retaining screws to secure the controller

in place.

•For safe operation, proper switch cooling, and reduction of electromagnetic emissions, ensure

that a slot cover is installed on any unused controller slot. For safety, no more than one slot

should be uncovered at a time when the switch is powered on.

•Respect the temperature specifications for the controller.

When installing the controller into a switch, the switch can be powered on or off. The installation

procedure in this guide assumes the switch is powered on.

Environmental specifications

Non-Operating

-10°C to 65°C (14°F to 149°F)

Operating

0°C to 40°C (32°F to 104°F)1,2

Temperature

15% to 90% at 65°C (149°F)15% to 90% at 40°C (104°F)Relative humidity (non-condensing)

4.6 km (15,000 ft)3.0 km (10,000 ft)Maximum altitude

1The maximum operating temperature specification of the chassis is affected by the number and location of the controllers

installed in the chassis. For the 5400 zl chassis, if all four (the maximum number of controllers allowed in a switch)

controllers are installed in the left hand side of the chassis, the maximum operating temperature specification is set to

50°C for the chassis. If any controllers are installed on the right hand side of the chassis, then the temperature specification

for the chassis is 40°C. A 5406 zl chassis has only three slots on the left. To stay within the 50°C temperature specification,

only three controllers are supported in this chassis.

2For the 8212 zl chassis, the maximum operating temperature specification is 40°C.

Other documentation

For full information on configuring and managing the controller, see the MSM Controllers

Configuration Guide.

Installation precautions 7

2 Installing

WARNING! This is a general procedure. It is the installer’s responsibility to perform the installation

in accordance with local electrical code and regulations.

A maximum of four controllers can be installed in the same chassis. Under certain conditions, a

maximum of three controllers are supported in the 5406 zl chassis. See “Environmental

specifications” (page 7).

Installation procedure

1. Use a Torx T-10 or flat-bladed screwdriver to unscrew the screws in the cover plate over the

slot where the controller is to be installed. Remove the cover and store the cover plate for

possible future use.

2. Hold the controller by its bulkhead, taking care not to touch the metal connectors or components

on the board.

3. Open the extractor handles (1 in figure below).

4. Aligning with the guides in the slot, insert the controller and slide it into the slot until it is fully

inserted (2 in figure below).

5. Once the contacts have engaged, use the extractor handles to seat the controller completely.

6. Tighten the screws.

Figure 6 Controller being installed

1. Extractor handles

2. Controller being inserted

8 Installing

Verifying the controller is installed correctly

When the controller is installed properly, it undergoes a self test that takes a few seconds. This

happens both when the switch is powered-on after installing the controller and when the controller

is installed while the switch already has power. The LEDs help determine if the controller has passed

the self test, as described in the following table.

Display for a properly installed controllerLocation of LEDLED

On briefly while the controller is undergoing self test, then off.

Note: If the controller was installed with the switch powered off,

and then the switch was powered on, the Test LED will stay on for

the duration of the switch self test.

SwitchTest

Figure 2 (page 5) and Figure 3 (page 5) show the location of

the Test, Fault, and controller Status LEDs on a 5400 zl or 8212

zl series switch, respectively.

OffSwitchFault

The LED goes on as soon as the controller is installed and the

switch is powered on, and stays on.

SwitchModule Status

The LED blinks green during initialization. On green means that

controller is operational.

“Controller front panel” (page 4) shows the location of all

controller LEDs.

ControllerModule Status

The LED goes on when HDD/CF initialization was successful. It is

off by default.

ControllerHDD and CF Status

Error conditions

Error conditions indicated by the controller LEDs are described in “Front panel port and LEDs”

(page 4)

NOTE: Allow sufficient time for the controller to start up, or you will receive an error message.

Verifying the controller is installed correctly 9

3 Initially connecting and configuring

This chapter describes how to connect to the switch, activate a controller, configure the switch for

the controller, and then perform initial controller configuration. Finally, information on restarting

and resetting the controller is provided.

Connect to the switch

Although full information on the switch command line interface (CLI) is provided in the switch

documentation, the basic switch CLI commands needed to work with the controller are provided

in this document.

NOTE: Although not described in this document, it is also possible to perform switch configuration

via a telnet session with an Ethernet connection to the switch.

1. Using a null-modem (crossover) serial cable, connect a computer to the serial port of the switch

Management Module.

2. On the computer, configure a serial terminal program in VT100 mode, with baud rate 9600,

8 data bits, no parity, 1 stop bit, and no flow control.

3. Open a terminal session with the switch and press Enter several times until the welcome screen

appears. (A different screen may appear if another session was already open.)

4. Press any key to continue. The switch CLI prompt appears. It looks similar to this:

HP Switch 5406zl#

5. If instead, the switch menu is shown, return to the top-level menu and then exit to the CLI by

selecting Command Line (CLI) on the Main Menu.

The switch CLI prompt appears, similar to this.

HP Switch 5406zl#

10 Initially connecting and configuring

Andere Handbücher für ProCurve MSM765zl

Inhaltsverzeichnis

Andere HP Controller Handbücher

HP ProCurve MSM765zl Bedienungsanleitung

HP 9000 Series 300 Anleitung zur Verwendung

HP MSM7XX Bedienungsanleitung

HP Aruba 7010 Series Bedienungsanleitung

HP HPE MR Gen11 Bedienungsanleitung

HP E-MSM720 Bedienungsanleitung

HP netRAID-1M Bedienungsanleitung

HP VXI 75000 C Series Betriebsanleitung

HP StorageWorks P2000 Bedienungsanleitung

HP HSG80 - StorageWorks RAID Array Controller Bedienungsanleitung

HP 3100ES - Smart Array RAID Controller Bedienungsanleitung

HP P Class 450/500/550/600/650/700/750 Bedienungsanleitung

HP Smart Array P712m Gebrauchsanweisung

HP HSG80 - StorageWorks RAID Array Controller Handbuch

HP ProCurve MSM760 Bedienungsanleitung

HP VXI Pentium 75000 Series Bedienungsanleitung

HP 30242 Handbuch

HP 3X-DEGXA-XX PCI-X Bedienungsanleitung

HP 8169A Bedienungsanleitung

HP Surestore Disk Array 12h - And FC60 Bedienungsanleitung

HP Compaq Presario,Presario 4400 Leitfaden

HP 9000 Series 300 Bedienungsanleitung

HP MR Gen10 Plus Bedienungsanleitung

HP 615418-B21 Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung

3M MicroTouch EX113 Bedienungsanleitung

KUHN

KUHN TKS Bedienungsanleitung

S&C

S&C PMH Bedienungs- und Wartungshandbuch