HP Deskpro 4000 Technisches Dokument

Compaq Deskpro 4000 and 6000 Series of Personal Computers A-1

appendix A

CONNECTOR PIN ASSIGNMENTS

This appendix contains the pin assignments for all external connectors:

Table A-1

Enhanced Keyboard

Connector and Icon (Orange) Pin Signal

KEY

Data

Unused

Ground

+5 VDC

Clock

Unused

Table A-2

Mouse

Connector and Icon (Green) Pin Signal

KEY

Data

Unused

Ground

+5 VDC

Clock

Unused

A-2 Connector Pin Assignments

Table A-3

Parallel Interface

Connector and Icon Pin Signal

22232425

910111213 8 7 6 5

20 19 1821 17 141516

2341 1

18-25

Strobe

Data Bit 0

Data Bit 1

Data Bit 2

Data Bit 3

Data Bit 4

Data Bit 5

Data Bit 6

Data Bit 7

Acknowledge

Busy

Paper End

Select

Auto Linefeed

Error

Initialize Printer

Select IN

Signal Ground

Table A-4

Serial Interfaces

Connector and Icon Pin Signal

12345

6789

Carrier Detect

Receive Data

Transmit Data

Data Terminal Ready

Signal Ground

Data Set Ready

Request to Send

Clear to Send

Ring Indicator

Compaq Deskpro 4000 and 6000 Series of Personal Computers A-3

Table A-5

Monitor

Connector Pin Signal

KEY

12345

15 14 13 12 11

Red Analog

Green Analog

Blue Analog

Monitor ID Bit2

Ground

Ground Analog

Not Connected

Ground

Monitor ID Bit 0

Bi-directional Data (SDA)*

Horizontal Sync

Vertical Sync

Data Clock (SCL)*

* For DDC support (I2C monitors)

Table A-6

Ethernet RJ-45

Connector and Icon Pin Signal

(+) Transmit Data

(-) Transmit Data

(+) Receive Data

Unused

(-) Receive Data

Unused

A-4 Connector Pin Assignments

Table A-7

Ultra SCSI

Connector and Icon Pin Signal

1-11

15-25

Ground

Reserved

Open

Reserved

Ground

DBO

DB1

DB2

DB3

DB4

DB5

DB6

DB7

DBP

Ground

Reserved

TERMPWR

Reserved

Ground

ATN #

Ground

BSY #

ACK #

RST #

MSG #

SEL #

C/D

REQ #

Input/Output

Compaq Deskpro 4000 and 6000 Series of Personal Computers A-5

Table A-8

Line-Out Audio Connector

Connector and Icon

1/8-inch Miniphone

Table A-9

Line-In Audio Connector

Connector and Icon

1/8-inch Miniphone

Table A-10

Microphone Connector

Connector and Icon (Blue)

Stereo 1/8-inch Miniphone

Table A-11

Headphone Connector

Connector and Icon

Stereo 1/8-inch Miniphone

A-6 Connector Pin Assignments

Table A-12

USB Connector

Connector and Icon Pin Signal

1234

VCC

- Data

+ Data

Ground

Compaq Deskpro 4000 and 6000 Series of Personal Computers A-7

Table A-13

External Infrared Transceiver

Connector and Icon Pin Signal

KEY

Transmit

Receive

Ground

Mode

Not Used

Not used

Table A-14

Ethernet AUI

Connector and Icon Pin Signal

13 12 11 10

5643

15 14

12 1

Ground

(+) Collision Detect

(+) Transmit Data

Ground

(+) Receive Data

Ground

Not Used

Ground

(-) Collision Detect

(-) Transmit Data

Ground

(-) Receive Data

+12V Supply

Ground

Not Used

Compaq Deskpro 4000 and 6000 Series of Personal Computers

B-1

appendix B

POWER CORD SET

REQUIREMENTS

The voltage select switch feature on the computer permits it to operate from any line voltage between

100-120 or 200-240 volts AC.

The power cord set received with the computer meets the requirements for use in the country where

you purchased the equipment.

Power cord sets for use in other countries must meet the requirements of the country where you use

the computer. For more information on power cord set requirements, contact your authorized

Compaq dealer, reseller or service provider.

General Requirements

The requirements listed below are applicable to all countries:

1. The length of the power cord set must be at least 6.00 feet (1.8 m) and a maximum of 9.75 feet

(3.0 m).

2. All power cord sets must be approved by an acceptable accredited agency responsible for

evaluation in the country where the power cord set will be used.

3. The power cord set must have a minimum current capacity of 10A and a nominal voltage rating

of 125 or 250 volts AC, as required by each country’s power system.

4. The appliance coupler must meet the mechanical configuration of an EN 60 320/IEC 320

Standard Sheet C13 connector, for mating with appliance inlet on the Switch Box.

B-2

Power Cord Set Requirements

Country-Specific Requirements

Power Cord Set Requirements–By Country

Country Accrediting Agency Applicable Note Numbers

Australia EANSW 1

Austria OVE 1

Belgium CEBC 1

Canada CSA 2

Denmark DEMKO 1

Finland SETI 1

France UTE 1

Germany VDE 1

Italy IMQ 1

Japan JIS 3

Norway NEMKO 1

Sweden SEMKO 1

Switzerland SEV 1

United Kingdom BSI 1

United States UL 2

NOTES:

1. The flexible cord must be <HAR> Type HO5VV-F, 3-conductor, 1.0 mm2 conductor size. Power

cord set fittings (appliance coupler and wall plug) must bear the certification mark of the agency

responsible for evaluation in the country where it will be used.

2. The flexible cord must be Type SJT or equivalent, No. 18 AWG, 3-conductor. The wall plug

must be a two-pole grounding type with a NEMA 5-15P (15A, 125V) or NEMA 6-15P (15A

250V) configuration.

3. The appliance coupler, flexible cord, and wall plug must bear a "T" mark and registration number

in accordance with the Japanese Dentori Law. The flexible cord must be Type VCT or VCTF,

3-conductor, 0.75 mm2 conductor size. The wall plug must be a two-pole grounding type with a

Japanese Industrial Standard C8303 (15A, 125V) configuration.

Compaq Deskpro 4000 and 6000 Series of Personal Computers C-1

appendix C

HARD DRIVES

Compaq Computer Corporation uses IDE hard disk drives that conform to two different

primary/secondary implementations. These are Conner mode and ATA-compatible mode. These two

modes are incompatible with one another.

If installing a second Ultra ATA hard drive on the primary controller, you must use an 80-conductor

ATA cable for optimal performance.

Device 0/Device 1 Relationship

A device 0/device 1 relationship exists when there are two hard drives connected to a single port. In

this situation, one drive must be designated as the device 0, or primary drive and the other as the

device 1, or secondary drive. This designation is necessary because both drives cannot work

simultaneously.

Cable Select

The Compaq Deskpro 4000 Series of Personal Computers use cable-select technology for identifying

Device 0 (primary) and Device 1 (secondary) IDE hard drives. Check that the jumpers on the IDE

hard drives are set properly for cable-select installation. Always check the label on the drives or

check Chapter 7 of this manual when a new drive is added to verify that the jumper settings are set

correctly.

 Cable select may not function properly if drives other than those supported by Compaq are

installed.

 The second drive on a cable-select cable can be a CD-ROM drive. However, the CD-ROM drive

must be installed in the device 1 position if a hard drive is installed on the same cable. Ensure

that both drives are set for cable-select configuration. See Chapter 7 for more information.

 If two drives are already connected to the primary IDE controller and an additional drive is to be

installed, the secondary IDE controller must be enabled. The secondary IDE controller can be

enabled by checking this option after opening the Advanced box in the Mass Storage group of

F10 Computer Setup. See Chapter 8 for more information.

 When more than two drives are installed, drive performances are best when the two faster drives

are connected to the primary IDE controller and the slower drive is connected to the secondary

IDE controller.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere HP Desktop Handbücher

HP Kayak XU800 Series Bedienungsanleitung

HP Deskjet 3000 Bedienungsanleitung

HP Omni 305-5300 Bedienungsanleitung

HP Pavilion t442k Bedienungsanleitung

HP Spectre One 23-e000 Bedienungsanleitung

HP Compaq Presario Handbuch

HP 743 Series Gebrauchs- und Pflegehandbuch

HP Pavilion a600 - Desktop PC Bedienungsanleitung

HP 9835A Betriebsanleitung

HP Pavilion t400 - Desktop PC Bedienungsanleitung

HP Pavilion t700 - Desktop PC Montageanleitung

HP Compaq dx2710 Microtower Einrichtungshandbuch

HP Spectre x360 Convertible Handbuch

HP Desktop PC 390 Montageanleitung

HP EliteDesk 800 G1 series Bedienungsanleitung

HP 8000 - Elite Convertible Minitower PC Einrichtungshandbuch

HP Compaq Presario Montageanleitung

HP dx6120 - Microtower PC Gebrauchsanweisung

HP X Class 500/550MHz Bedienungsanleitung

HP Media Center m1100 - Desktop PC Technisches Datenblatt

HP EX470 - MediaSmart Server - 512 MB RAM Anleitung zur Verwendung

HP Pavilion v500 - Desktop PC Gebrauchsanweisung

HP Workstation xw8000 Stücklistenhandbuch

HP DV3 Handbuch

Beliebte Desktop Handbücher anderer Marken

Asus

Asus E210 Series Bedienungsanleitung

Dell

Dell Inspiron 600m Bedienungsanleitung

Dell

Dell Inspiron 3662 Bedienungsanleitung

TotalFlow

TotalFlow uFLO Bedienungsanleitung

Logitech

Logitech MK320 Bedienungsanleitung

Dell

Dell XPS 730 H2C Bedienungsanleitung

Sony

Sony Vaio Series Bedienungsanleitung

Sony

Sony VGC-LT32E - Vaio All-in-one Desktop Computer Bedienungsanleitung

Alto

Alto MD 250 Bedienungsanleitung

Arbor Technology

Arbor Technology FPC-7800 Series Bedienungsanleitung

Sony

Sony VAIO VGX-TP1 Series Bedienungsanleitung

Asus

Asus Eee Box B204 Bedienungsanleitung

Dell

Dell Optiplex 9010 All In One Bedienungsanleitung

Everex

Everex eXplora Bedienungsanleitung

Lenovo

Lenovo ThinkCentre M75e Bedienungsanleitung

Dell

Dell Alienware Area-51 R4 Bedienungsanleitung

Compaq

Compaq iPAQ Internet Device Bedienungsanleitung

Parker

Parker PA Series Bedienungsanleitung