HP Kayak XU Series 03 Bedienungsanleitung

HP Kayak XU 03xx PC Workstation —

Installing Accessories

In Your HP PC Workstation

Explains in detail how to install accessories, such as extra memory,

accessory boards, and additional disk drives.

03xx-i~1.fm Page 1 Tuesday, February 16, 1999 10:15 AM

HP Kayak XU 03xx PC Workstation — Installing Accessories In Your HP PC Workstation

Supported HP Accessories

2English

Supported HP Accessories

Contact your dealer for an up-to-date list of supported devices.

NOTE 256 MB registered ECC SDRAM DIMMs cannot be used with unbuffered

32 MB, 64 MB or 128 MB DIMMs

Up to six accessory boards

can be installed:

- One AGP slot (graphics)

- Three 32-bit PCI slots (one used by SCSI/LAN board, one with RAIDport)

- One combination PCI or ISA slot

- One 16-bit ISA slot

Front Access Drives, for example:

- 3.5-inch 1.44 MB flexible disk drive

(one third height)

- 5.25-inch 1.2 MB flexible disk drive

(half height)

- 5.25-inch tape drive (half height)

Internal Mass

Storage Devices

5 Pairs of Rails for Front

Access Devices:

- 3.5-inch disk drive rails

- 5.25-inch disk drive rails

Main Memory Upgrades

(DIMM slots for ECC SDRAM):

- 32 MB (unbuffered)

- 64 MB (un-buffered)

- 128 MB (un-buffered)

- 256 MB (Registered - see note below)

03xx-i~1.fm Page 2 Tuesday, February 16, 1999 10:15 AM

English 3

HP Kayak XU 03xx PC Workstation — Installing Accessories In Your HP PC Workstation

Removing and Replacing the Cover

WARNING For your safety, never remove the PC Workstation’s cover without first

removing the power cord from the power outlet, and any connection to

a telecommunications network. Always replace the cover on the

PC Workstation before switching it on again.

Removing the Cover

1Switch off the display and computer.

2Disconnect all power cables and any telecommunications cables.

3If necessary, unlock the cover using the key on the back panel.

4Lift the two latches on the front sides of the computer upwards.

5Grasp the cover on the sides at the back of the computer and slide

it forwards and off the computer.

Step 4

Step 5

03xx-i~1.fm Page 3 Tuesday, February 16, 1999 10:15 AM

HP Kayak XU 03xx PC Workstation — Installing Accessories In Your HP PC Workstation

Removing and Replacing the Cover

4English

Replacing the Cover

1Ensure that you have installed all your accessories and that all

internal cables are properly connected and safely routed.

2Ensure that the two latches on the front sides of the cover are lifted

up, and that the lock is unlocked.

3Slide the cover onto the computer, making sure that the two guides

at the bottom of the case slide into the two rails at the base of the

computer. Firmly slide the cover backwards into position.

4Lower the latches on the front sides of the cover.

5If required, lock the cover using the key provided.

6Reconnect all the power cables.

Press here on

both sides of the

PC’s cover.

Step 3

Step 4

Step 5

03xx-i~1.fm Page 4 Tuesday, February 16, 1999 10:15 AM

English 5

HP Kayak XU 03xx PC Workstation — Installing Accessories In Your HP PC Workstation

Removing and Replacing the Cover

Intrusion Monitor Your PC Workstation is equipped with an intrusion monitor, which is

located on the front of the PC Workstation, behind the Hardware

Control Panel. It is designed to detect whether your PC Workstation

has been opened since the last time it was used:

•If your PC Workstation has been opened, it is assumed that the

system configuration has changed and a full start-up check is carried

out.

•If your PC Workstation has not been opened, it is assumed that the

system configuration has not changed and a reduced start-up check

is carried out.

03xx-i~1.fm Page 5 Tuesday, February 16, 1999 10:15 AM

HP Kayak XU 03xx PC Workstation — Installing Accessories In Your HP PC Workstation

Moving the Power Supply

6English

Moving the Power Supply

1Disconnect the computer’s power cord and any telecommunications

cable.

2Remove the computer’s cover (refer to page 3).

3Press the retaining buttons on each side of the HP UltraFlow airflow

guide and lift it partly out of the PC Workstation’s case.

4Remove the fan connection to the system board and lift the airflow

guide completely out of PC Workstation’s case.

5Unscrew the four self-retaining screws at the back of the power

supply.

HP UltraFlow

Airflow Guide

Retaining button

Fan connection to

system board

Unscrew the

self-retaining screws

03xx-i~1.fm Page 6 Tuesday, February 16, 1999 10:15 AM

English 7

HP Kayak XU 03xx PC Workstation — Installing Accessories In Your HP PC Workstation

Moving the Power Supply

WARNING To avoid electrical shock, do not open the power supply.

6Slide the power supply out of the computer until it stops—the

power supply unit remains connected to the computer.

Replacing the Power

Supply after Installing

Accessories

1Check that all internal cables are safely routed.

2Slide the power supply back into the computer.

3Tighten the four self-retaining screws.

4Replace the HP UltraFlow airflow guide.

5Reconnect the fan to the system board.

Slide the power

supply unit clear of

the computer

Power Supply

03xx-i~1.fm Page 7 Tuesday, February 16, 1999 10:15 AM

HP Kayak XU 03xx PC Workstation — Installing Accessories In Your HP PC Workstation

Installing Memory

8English

Installing Memory

Main Memory Modules

If you need more main memory to run your application software, you

can install up to 1GB of memory in four DIMM slots.

Main memory upgrades are available in single 32 MB, 64 MB and

128 MB Unbuffered ECC SDRAM or 256 MB Registered ECC SDRAM

memory modules. You should note that Registered ECC SDRAM

cannot be used with Unbuffered memory modules. Do not attempt to

combine these two types of memory.

CAUTION Static electricity can damage electronic components. Turn off all

equipment. Do not let your clothes touch the accessory.

To equalize the static electricity, rest the accessory bag on top of the

power supply while you are removing the accessory from the bag.

Handle the accessory as little as possible and with care.

To install a main memory module:

1Disconnect the computer’s power cord and any LAN or

telecommunications cable.

2Remove the computer’s cover (refer to page 3).

3Press the retaining buttons on each side of the HP UltraFlow airflow

guide and lift it partly out of the PC Workstation’s case.

4Remove the fan connection to the system board and lift the airflow

guide completely out of PC Workstation’s case.

NOTE Refer to the illustration on page 6 for steps 3 and 4.

5Remove the Ultra wide 16-bit SCSI cable from the system board.

6Remove the power supply and the transparent airflow guide

covering the processor sockets (if needed).

7Remove the floppy disk drive data cable from the system board.

03xx-i~1.fm Page 8 Tuesday, February 16, 1999 10:15 AM

English 9

HP Kayak XU 03xx PC Workstation — Installing Accessories In Your HP PC Workstation

Installing Memory

8The location of the memory module slots is shown here.

9Slide the memory module into the slot at 90° to the system board

(with the cutouts furthest away from the processor).

10 Firmly press the memory module completely into the connector

until the retaining clips click into position. Repeat this procedure for

each additional memory module you want to install.

11 Install any other accessories if necessary, then replace all units and

reconnect all cables and power cords. Replace the cover (refer to

page 4).

12 Check the HP Summary Screen to verify the new configuration.

Slide the memory module into the

slot at 90oto the system board

Push the module until the

retaining clips click into position

Memory module

cutouts

03xx-i~1.fm Page 9 Tuesday, February 16, 1999 10:15 AM

HP Kayak XU 03xx PC Workstation — Installing Accessories In Your HP PC Workstation

Installing Memory

10 English

Installing More Memory on the Video Adapter

Your PC Workstation is equipped with a video adapter that supports

2D and 3D graphics. If you need to have more video memory to display

more colors, higher resolutions, or for increased speed, you can install

more video memory on the video adapter.

To find out about available video memory upgrades, refer to the HP

World Wide Web Site at

http://www.hp.com/go/kayaksupport/

CAUTION Static electricity can damage electronic components. Turn off all

equipment. Do not let your clothes touch the accessory.

To equalize the static electricity, rest the accessory bag on top of the

power supply while you are removing the accessory from the bag.

Handle the accessory as little as possible and with care.

To install a video memory module:

1Switch off the display and computer, and disconnect the power

supply cables and any telecommunications cables. Remove the

computer’s cover (refer to page 3) and carefully place the

PC Workstation on its side.

2Carefully remove the board from the accessory slot, holding the

board at each end by its top edge. Do not bend the board. With its

components facing up, place the board on a clean, flat, solid,

static-free surface. Handle the board by its edges.

3Attach the memory module to the connectors on the video adapter.

4Replace the video adapter in the computer. Carefully slide the board

back into its accessory slot. Firmly press the board into the socket.

Make sure that the board slides into the socket completely and does

not touch components on other boards. Secure the video adapter.

5Install any other accessories before replacing the cover (refer to

page 4). Reconnect all cables and power cords.

03xx-i~1.fm Page 10 Tuesday, February 16, 1999 10:15 AM

Andere Handbücher für Kayak XU Series 03

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere HP Desktop Handbücher

HP 512n - Pavilion - 128 MB RAM Bedienungsanleitung

HP Pavilion d4600 - Desktop PC Technisches Datenblatt

HP Vectra VE 5/xx Series Bedienungsanleitung

HP ProDesk 680 G6 PCI Montageanleitung

HP Pavilion t340 Bedienungsanleitung

HP Z200 - Small Form Factor Workstation Bedienungsanleitung

HP Brio 8172 Bedienungsanleitung

HP ZX2000 Bedienungsanleitung

HP Vectra 486M - MI Bedienungsanleitung

HP Pavilion a1000 - Desktop PC Bedienungsanleitung

HP Compaq 4000 Pro series Einrichtungshandbuch

HP Evo D500 - Convertible Minitower Bedienungsanleitung

HP Media Center m500 - Desktop PC Bedienungsanleitung

HP Media Center m7200 - Desktop PC Technisches Datenblatt

HP Visualize j6000 Referenzhandbuch

HP Pavilion k300 - Desktop PC Montageanleitung

HP 8000f - Elite Ultra-slim Desktop PC Bedienungs- und Wartungshandbuch

HP ENVY 23-c000 Bedienungsanleitung

HP d325 Series Gebrauchsanweisung

HP TouchSmart 9300 Elite Gebrauchsanweisung

HP b2600 Gebrauchs- und Pflegehandbuch

HP -380467-003 - COMPAQ PRESARIO C300 C500 C700 F500 F700 LAPTOP... Betriebsanleitung

HP Pavilion t142 Bedienungsanleitung

HP Xw4400 - Workstation - 2 GB RAM Kurzanleitung

Beliebte Desktop Handbücher anderer Marken

Asus

Asus E210 Series Bedienungsanleitung

Dell

Dell Inspiron 600m Bedienungsanleitung

Dell

Dell Inspiron 3662 Bedienungsanleitung

TotalFlow

TotalFlow uFLO Bedienungsanleitung

Logitech

Logitech MK320 Bedienungsanleitung

Dell

Dell XPS 730 H2C Bedienungsanleitung

Sony

Sony Vaio Series Bedienungsanleitung

Sony

Sony VGC-LT32E - Vaio All-in-one Desktop Computer Bedienungsanleitung

Alto

Alto MD 250 Bedienungsanleitung

Arbor Technology

Arbor Technology FPC-7800 Series Bedienungsanleitung

Sony

Sony VAIO VGX-TP1 Series Bedienungsanleitung

Asus

Asus Eee Box B204 Bedienungsanleitung

Dell

Dell Optiplex 9010 All In One Bedienungsanleitung

Everex

Everex eXplora Bedienungsanleitung

Lenovo

Lenovo ThinkCentre M75e Bedienungsanleitung

Dell

Dell Alienware Area-51 R4 Bedienungsanleitung

Compaq

Compaq iPAQ Internet Device Bedienungsanleitung

Parker

Parker PA Series Bedienungsanleitung