HP D6000 Disk Enclosure Bedienungsanleitung

HP D6000 Disk Enclosure

Installation Instructions

Part Number: 682252-001

September 2012

Edition: 1

Rack warnings

WARNING: To reduce the risk of personal injury or damage

to the equipment, be sure that:

•The leveling jacks are extended to the floor.

•The full weight of the rack rests on the leveling jacks.

•The stabilizing feet are attached to the rack if it is a

single-rack installation.

•The racks are coupled together in multiple-rack

installations.

•Only one component is extended at a time. A rack may

become unstable if more than one component is extended

for any reason.

WARNING: To reduce the risk of personal injury or

equipment damage when unloading a rack:

•At least two people are needed to safely unload the rack

from the pallet. An empty 42U rack can weigh as much as

115 kg (253 lb), can stand more than 2.1 m (7 ft) tall, and

might become unstable when being moved on its casters.

•

Never stand in front of the rack when it is rolling down the

ramp from the pallet. Always handle the rack from both

sides.

Site requirements

Select an installation site that meets the detailed installation site requirements

described in the user guide on the Documentation CD.

1Installing the enclosure

WARNING: The D6000 with no drives installed weighs

72.58 kg (160.00 lb). With all drives and components

installed, the enclosure can weigh up to 145.15 kg (320 lb).

Before configuring your rack solution, be sure to check the

manufacturer weight limits and specifications. Failure to do so

can result in physical injury or damage to the equipment and

the facility.

CAUTION: Always plan the rack installation so that the

heaviest item is on the bottom of the rack. Install the heaviest

item first, and continue to populate the rack from the bottom to

the top.

CAUTION: HP has not tested or validated the D6000 with

any third-party racks. Before installing the D6000 in a

third-party rack, be sure to properly scope the limitations of

the rack and consider the following:

•You must fully understand the static and dynamic load

carrying capacity of the rack and be sure that it can

accommodate the weight of the D6000.

•You must install a 1U tray beneath the D6000 to ensure

proper support.

•Be sure sufficient clearance exists for cabling, installation

and removal of the enclosure, actuation of the rack doors,

and full articulation of the drive drawers.

IMPORTANT: Some racks other than the HP Rack 10000

Series rack do not allow full access to hard drive bays 29–35

in hard drive drawer 2.

The rack rails are marked for easy identification. The left rack rail is marked "L" and

the right rack rail is marked "R."

To install the rack rails:

1. Begin with the left rack rail. Align the end of the rail with the rear rack column.

2. Slide the rack rail closed until the end of the rail is locked in place, wrapping

behind the rear rack column.

3. Slide the front end of the rail to the rack front column. When fully seated, the

rack rail will lock into place.

4. Repeat the procedure for the right rack rail.

WARNING: The enclosure is very heavy. To reduce the risk

of personal injury or damage to the equipment:

•Observe local occupational health and safety

requirements and guidelines for manual material

handling.

•Remove all installed enclosure components from their

enclosures before installing or moving the enclosures.

•Use caution and get help to lift and stabilize enclosures

during installation or removal, especially when the

enclosure is not fastened to the rack.

WARNING: Always use at least two people to lift an

enclosure into the rack. If the enclosure is being loaded into

the rack above chest level, a third person must assist with

aligning the enclosure with the rails while the other two

people support the weight of the enclosure.

5. Install the enclosure, making sure to tighten the thumbscrews to secure the

enclosure to the rack.

The installation is complete.

2Installing the hard drives

A D6000 supports up to 35 hard drives per storage drawer. For weight-distribution

purposes and best-possible cooling, populate hard drive bays from the rear to the

front, starting with the highest device bay ID number. To properly distribute air flow

and cool the installed drives, make sure that all drive bays are populated with a drive

or a drive blank.

Before installing the drives, confirm that they are supported for use in the enclosure.

For more information, see the QuickSpecs on the HP website

(http://www.hp.com/go/d6000/quickspecs).

When adding hard drives to the hard drive drawer, observe the following general

guidelines:

•Verify that the drives are fully seated before closing the drawer.

•The drawer is fully closed when the fans slow down to their normal speed.

•The drawer should be closed with the handle in the released position.

•Hard drives are sensitive to excess vibration. Use care when opening and

closing the drawer.

•A RAID 1 mirror requires an even number of hard drives.

•Drives that will be configured within an array should be the same capacity to

provide the greatest storage space efficiency.

NOTE: ACU does not support mixing SAS and SATA drives

in the same logical volume.

To install the drives:

1. Be sure all I/O bays contain either an I/O module or an I/O blank. The hard

drive drawer does not open if I/O bays are empty.

2. Be sure the I/O modules or I/O blanks are fully seated and their handles are in

the locked position. The hard drive drawer does not open if I/O modules or I/O

blanks are not fully seated with their handles in the locked position.

WARNING: TIP HAZARD! To reduce the risk of personal

injury or damage to the equipment, do not extend the hard

drive drawers beyond the supporting surface when the unit is

not installed in a rack.

WARNING: To reduce the risk of personal injury or damage

to the equipment, ensure that only one hard drive drawer is

extended at a time.

3. Extend the hard drive drawer.

WARNING: Pinch hazard—Keep hands out of front and rear

of chassis when closing hard drive drawers.

CAUTION: To prevent improper cooling and thermal

damage, do not operate the D6000 for an extended period of

time with the drawer open.

CAUTION: To prevent improper cooling and thermal

damage, do not operate the D6000 unless all bays are

populated with either a component or a blank.

4. Remove the hard drive blank.

5. Prepare the hard drive.

6. Install the hard drive.

WARNING: Pinch hazard—Keep hands out of front and rear

of chassis when closing hard drive drawers.

7. When all drives have been installed, close the hard drive drawer.

3Installing optional I/O modules

The D6000 ships with two I/O modules, one for each storage drawer. Installing

additional I/O modules expands support from single-domain to dual-domain.

CAUTION: If the I/O module is installed in an enclosure for

which it was not designed, the module will not function

properly. Read the labels on the I/O module and the

enclosure to confirm compatibility. For example, an I/O

module with a "6G IO module" label is supported for use only

in the 6G, D6000 disk enclosure; an I/O module with no

label is supported for use only in a 3G disk enclosure such as

the MDS600.

To install an I/O module:

1. Be sure the hard drive drawer is closed completely.

2. To remove the I/O blank, release the I/O blank handle, pull the I/O blank

handle down until it ejects the I/O blank, and then remove the I/O blank from

the enclosure.

3. To install the I/O module, insert the I/O module into the enclosure and push the

I/O module handle up. Be sure the I/O module is seated fully, and the I/O

module handle is in the locked position.

The installation installation is complete.

To install the second I/O module in the other enclosure drawer, repeat the

procedure.

CAUTION: For best cooling practices, do not operate the

enclosure for extended periods with more than one

component or blank removed. When removing an active

component, replace it with a blank.

4Cabling the D6000

After installing the D6000 in a rack, connect the I/O cables and power cords to the

rear panel.

IMPORTANT: To achieve 6G performance, all components

in a system (hard drives, disk enclosures, switches, and

controllers) must be 6G capable.

Mini-SAS I/O cables

The D6000 does not ship with any I/O cables, but supports the use of 2.00 m (6.56

ft) mini-SAS cables.

For information about the supported cables, see the QuickSpecs on the HP website

(http://www.hp.com/go/d6000/quickspecs).

Observe the following guidelines:

•Only use supported 2.00 m (6.56 ft) external mini-SAS cables.

•Always be sure that the servers attached to the D6000 are powered down

before connecting SAS cables.

The D6000 can be deployed in the following environments:

•Direct-connect: Connected directly to a rack-mounted or stand-alone server with

a supported Smart Array controller installed.

•Switch-connect: Connected to a SAS BL Switch installed in a BladeSystem

c-Class enclosure (and server blades with a supported Smart Array controller

installed.

In direct-connect and switch-connect environments, when one I/O module is installed

in each storage drawer, single domain is supported. When additional, optional I/O

modules are installed, dual-domain is supported.

Because each D6000 storage drawer is managed as a separate enclosure, the

drawers can be connected to different servers or switches.

To connect the mini-SAS I/O cables:

1. Connect a mini-SAS cable to port 1 on the primary (top) I/O module on the

designated storage drawer.

2. Connect the other end of the mini-SAS cable to a port on the switch or server

HBA.

3. If optional, additional I/O modules were installed, install an additional cable to

port 1 of the secondary (bottom) I/O module and to the redundant switch or

server HBA port.

4. Repeat these cabling steps to connect the other D6000 drawer.

The following illustration shows one example of cabling the D6000. For more

information and examples, see the following documents, available on the HP website

(http://www.hp.com/go/d6000/manuals):

•HP D6000 Disk Enclosure Direct Connect Cabling Guide

Andere Handbücher für D6000 Disk Enclosure

Inhaltsverzeichnis

Andere HP Gehäuse Handbücher

HP BladeSystem c7000 Handbuch

HP A3765A Bedienungsanleitung

HP Clemco 60 Leitfaden

HP D3600 Handbuch

HP StoreEver 1U Bedienungsanleitung

HP 418800-B21 - StorageWorks Modular Smart Array 70 Storage... Handbuch

HP D2000 Bedienungsanleitung

HP StorageWorks P2000 Bedienungsanleitung

HP MSA 1050 Bedienungsanleitung

HP BladeSystem c-Class Infrastructure Gebrauchsanweisung

HP 418800-B21 - StorageWorks Modular Smart Array 70 Storage... Anleitung zur Verwendung

HP TeemTalk Terminal Emulator 7.0 Leitfaden

HP BladeSystem c7000 Bedienungs- und Sicherheitshinweise

HP 418800-B21 - StorageWorks Modular Smart Array 70 Storage... Bedienungsanleitung

HP 6602 Bedienungsanleitung

HP 3PAR StoreServ 8 Series Montageanleitung

HP A5134A Bedienungsanleitung

HP 418800-B21 - StorageWorks Modular Smart Array 70 Storage... Bedienungsanleitung

HP D6000 Disk Enclosure Gebrauchsanweisung

HP J2000 Bedienungsanleitung

HP StorageWorks 2000sa Bedienungsanleitung

HP Visualize c3000 Gebrauchsanweisung

HP StorageWorks 50 Gebrauchsanweisung

Beliebte Gehäuse Handbücher anderer Marken

SilentiumPC

SilentiumPC Armis AR5 Handbuch

Pulsar

Pulsar 17/TRP80/DSPR Bedienungsanleitung

Thermaltake

Thermaltake V150 TG Bedienungsanleitung

MSI

MSI MPG SEKIRA 500X Bedienungsanleitung

Antec

Antec Dark fleet DF-10 Bedienungsanleitung

Nexans

Nexans WTC05 Bedienungsanleitung

Peavey

Peavey DS 1502 Bedienungsanleitung

D-Link

D-Link ShareCenter Pro DNS-1550-04 Bedienungsanleitung

Rosewill

Rosewill RX82-U(JBOD) Bedienungsanleitung

QNAP

QNAP SAS JBOD CLI 1.0 Bedienungsanleitung

GAMDIAS

GAMDIAS Talos P1 Bedienungsanleitung

Auvs

Auvs KR615 Bedienungsanleitung

Digitus

Digitus DA-71114 Bedienungsanleitung

CommScope

CommScope FDH 3000 Bedienungsanleitung

FS FHD-FWME4 Bedienungsanleitung

JBL

JBL CS1215T Bedienungsanleitung

Pulsar

Pulsar ARAD-S4 Bedienungsanleitung

Pulsar

Pulsar AWO454 Bedienungsanleitung