HP E3491A Montage- und Wartungsanleitung

Inhaltsverzeichnis

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

Keysight

Keysight M8290A Bedienungsanleitung

Acterna

Acterna MS1400 Bedienungsanleitung

R&S

R&S ZPH Bedienungsanleitung

Datacolor

Datacolor ColorReader DC10-2 Bedienungsanleitung

Installation and Service

Guide

Publication number E3491-97001

Second edition, August 1995

For Safety information, Warranties, and Regulatory information, see the

pages behind the index.

© Copyright Hewlett-Packard Company 1994, 1995

All Rights Reserved

HP E3491A Pentium Probe

HP E3491A Pentium Probe—At a Glance

The HP E3491A Pentium Probeprovides

a low-cost way to debug embedded

softwareforIntel Pentium

microprocessors. It can also be used

with theHP E2457A Preprocessor

Interface for microprocessor code

disassembly.

Thetargetconnection

The HP E3491APentium Probe connects

to your target microprocessor via a

special connector onthetargetsystem,

or through the HP E2457A Preprocessor

Interface.

The HP 16505A connection

The HP E3491APentium Probe connects

to theHP 16505A Prototype Analyzer via

an Ethernet LAN forremote operation,

or directly forpoint-to-point operation.

The logic analyzer connects to the

HP 16505A through a SCSI connector.

The configuration switches

Usethe switches to configure

communication to the HP 16505A. There

is a guide to these switches on the

bottom of the HP E3491A Pentium Probe.

The status LEDs

LEDs show the statusof the power

supply, the target system, and the

connection to the HP 16505A.

Additonal equipmentrequired

The HP E3491A Pentium Proberequires

the HP 16505APrototype Analzer.

Compatibility with other products

The HP E3491APentium Probe and

HP 16505A Prototype Analyzercan also

be used withthe HP E2457A

PreprocessorInterface.

ii

HP E3491A

Pentium Probe

Figure 1

iii

iv

Contents

Part 1 Installation

1 Connecting to the HP 16505A Prototype Analyzer

Equipment supplied 4

Installing the software in the HP 16505A Prototype Analyzer 5

Connecting the HP E3491A Pentium Probe to a Power Source 6

To choose a power cord 6

To connect the power cord and turn on the HP E3491A Pentium Probe 7

Connecting the Probe to the Prototype Analyzer 8

Connecting for a point-to-point configuration 9

Connecting to a LAN 10

To set the 10BASE-T configuration switches 12

Setting Up LAN Communication 13

To verify LAN communications 14

Setting Up a Serial Connection 15

To set the serial configuration switches 16

To connect a serial cable 16

To verify serial communications 17

To configure LAN parameters using the built-in terminal interface 18

2 Connecting to the Target System

Connectors provided 22

To test the HP E3491A Pentium Probe 23

To connect to a target system via the Intel defined debug port 23

To connect to a target system via the HP E2457A Pentium Preprocessor 24

v

Part 2 Reference

3 Designing a Target System

Designing a target system for use with the HP E2457A Preprocessor Inter-

face 30

Designing a target system for use with the Intel-defined debug port 31

4 Specifications and Characteristics

Processor Compatibility 34

Electrical Specifications 34

Environmental Specifications 36

Pinout for 30-pin HP E3491-66503 Adapter Board 37

5 Solving Problems

Status Lights 42

Problems with the LAN Interface 43

If you cannot verify LAN communication 43

If you have LAN connection problems 44

If the "POL" LED is lit 44

If it takes a long time to connect to the network 45

Problems with the Serial Interface 46

If you cannot verify RS-232 communication 46

If you have RS-232 connection problems with the MS Windows Terminal pro-

gram 46

Problems with the HP E3491A Pentium Probe Itself 48

To run the power up self test 48

To execute the built-in performance verification test 50

Contents

vi

Returning the HP E3491A Pentium Probe to Hewlett-Packard for Serv-

ice 56

To return the HP E3491A Pentium Probe to Hewlett-Packard 56

To obtain replacement cables 57

Figures

HP E3491A Pentium Probe iii

Powering up the Pentium Probe 7

Point-to-point Connection 9

LAN Connection 11

Switch Positions for LAN (left) and 10BASE-T LAN (right) Configurations,

S6 Open for Initialization 11

Connecting through the HP E2457A Preprocessor Interface 25

Status Lights 41

Contents

vii

Contents

viii

Part 1

Installation

2