HP Procurve radio port 220 Bedienungsanleitung

Installation and

Getting Started Guide

www.procurve.com

ProCurve Radio Port 220

The information contained herein is subject to change without

notice.

This document contains proprietary information, which is

protected by copyright. No part of this document may be

photocopied, reproduced, or translated into another

language without the prior written consent of Hewlett-

Packard.

Publication Number 5991-3779

Applicable Products

Trademark Credits

Windows NT®, Windows®, and MS Windows® are US

registered trademarks of Microsoft Corporation.

Disclaimer

HEWLETT-PACKARD COMPANY MAKES NO WARRANTY

OF ANY KIND WITH REGARD TO THIS MATERIAL,

INCLUDING, BUT NOT LIMITED TO, THE IMPLIED

WARRANTIES OF MERCHANTABILITY AND FITNESS

FOR A PARTICULAR PURPOSE. Hewlett-Packard shall not

be liable for errors contained herein or for incidental or

consequential damages in connection with the furnishing,

performance, or use of this material.

The only warranties for HP products and services are set

forth in the express warranty statements accompanying

such products and services. Nothing herein should be

construed as constituting an additional warranty. HP shall

not be liable for technical or editorial errors or omissions

contained herein.

Hewlett-Packard assumes no responsibility for the use or

reliability of its software on equipment that is not furnished

by Hewlett-Packard.

Warranty

See the Customer Support/Warranty booklet included with

the product.

A copy of the specific warranty terms applicable to your

Hewlett-Packard products and replacement parts can be

obtained from your HP Sales and Service Office or

authorized dealer.

ProCurve Radio Port 220 (J9005A)

Introduction

The ProCurve Radio Port 220, a component of the ProCurve Wireless LAN

System, links wireless 802.11a/b/g devices to the Ethernet network through a

wireless services-enabled switch. This device is to be used with the ProCurve

Switch 5300xl, with a ProCurve Wireless EDGE Services xl Module, or other

compatible wireless services-enabled switch product. These Radio Ports are

designed to be simple plug-and-play devices that require no individual device

configuration before being installed into a network. All Radio Port configu-

ration, including country-specific settings, radio channel, radio power, SSID

settings, security settings, management information, and Radio Port firmware

is provided through the wireless services-enabled switch.

NOTE Before installing this Radio Port, a wireless services-enabled switch (such as

the ProCurve Switch 5300xl with Wireless EDGE Services xl Module installed)

should be deployed, configured, and operating in a Normal mode. See the

"ProCurve Wireless EDGE Services xl Module Getting Started Guide" for

details.

ProCurve Radio Port 220 Package Contents

ProCurve Radio Port 220 with external antenna connectors (Plenum Rated)

NOTE External Antennae must be purchased separately.

■Two wall mount screws

■Two wall anchors

■Light pipe extender

■Badge for light pipe extender

■Label for badge

■Radio Port Install Guide

■Customer Support/Warranty booklet

Description

The ProCurve Radio Port 220 is a dual-radio IEEE 802.11-compliant device

supporting simultaneous 802.11a and 802.11b/g wireless Ethernet connec-

tions. The unit supports up to four external antennas, including up to two 2.4

GHz diversity antennas and up to two 5 GHz diversity antennas. Supported

Antennas are listed below under the section entitled Supported Antennas.

Introduction

The Radio Port 220 is designed for installation in either office or plenum

environments, using the mounting slots built into the underside of the metal

case. The Radio Port has one RJ-45 connector supporting 10/100 Ethernet and

requires power from any UL-listed, 802.3af-compatible Power over Ethernet

(PoE) switch or power injector.

RSMA Antenna Connectors

2.4 Ghz Primary5 Ghz Primary

2.4 Ghz Secondary5 Ghz Secondary

RSMA Antenna Connectors

LEDs

Top View

Mount Slots

Light Pipe Clip Slots

Bottom View

Introduction

Lock Port

The lock port, compatible with laptop-style security cables, is on the side of

the case.

Front View

Rear View RJ-45

Lock Port

Introduction

Technical Specifications

Dimensions & Weight

Features

■High-performance 802.11-compliant radios

■Two Reverse SMA (RSMA) connectors for 2.4-2.5Ghz antennas and two

Reverse SMA (RSMA) connectors for 4.9-5.825Ghz antenna connection

■Supports a single antenna or dual antennas in diversity mode for both

802.11b/g (2.4 GHz) and 802.11a (5GHz) bands

■Integrated 10/100 Base-TX Ethernet RJ-45 port

■Two redundant sets of LED indicators, top and bottom of Radio Port

■Lightpipe Extender for making LED indicators visible when Radio Port is

installed above a ceiling tile

■Safety wire tie point (post)

■Laptop-style lock port

■Slots for wall mounting

Operating Voltage 48VDC (from 802.3af-compliant

power source)

Operating Current 148mA (typical)

Power 7W (typical)

Operating Temperature -4 to 122° F (-20 to 50° C)

Non-Operating/Storage

Temperature -40°F to 158°F (-40 to 70°C )

Operating Humidity 5 to 95% (non-condensing)

Non-Operating/Storage

Humidity 5 to 95% (non-condensing)

Operating Altitude (max) 10,000 ft (3,048 m)

Non-Operating/Storage

Altitude 15,000ft.(4,572 m)

Plenum Rated UL 2043 - suitable for use in air

handling spaces

Length 237.2mm (9.34in.)

Width 139.6mm (5.50in.)

Height 25.4mm (1.0in.)

Weight 0.73kg (1.6lbs)

Introduction

Radio Characteristics

The ProCurve Radio Port 220 contains two IEEE 802.11-compliant radios: (1)

an 802.11b/g radio operating in the 2.4 to 2.5 GHz band and (2) an 802.11a radio

operating in the 4.9 to 5.875Ghz band. The Radio Port accepts a broad range

of 2.4-2.5GHz and 4.9-5.875GHz external antennas that can be connected to

the Radio Port's two pairs of R-SMA antenna connectors. The following table

lists the 802.11-compliant operating modes for each radio. The three sup-

ported 802.11g operating modes are simultaneous CCK and OFDM, CCK only,

or OFDM only.

Integrated RJ-45 Port

The ProCurve Radio Port 220 has one RJ-45 connector supporting a full-duplex

10/100Base-TX Ethernet port and requires IEEE 802.3af-compliant Power-

over-Ethernet (PoE) from an external source such as a Power-over-Ethernet

(PoE) switch or power injector. Installers can use of a single CAT-5 cable to

supply both Ethernet connectivity and power to the Radio Port, allowing these

Radio Ports to be installed up to 100 m (300 ft.) from a PoE-compliant 10/100

Ethernet port. There is no additional power supply required.

LED Indicators

The Radio Port 220 has LED indicators on the front of the case that visually

display the status of the device. When the Radio Port is mounted above a

suspended ceiling, an additional set of LED indicators on the back of the unit

can be extended through the ceiling tile using a provided lightpipe extender,

making the Radio Port location and status visible from below the ceiling.

Device Mbps Data Rate Support Utilizing

Diversity GHz

802.11a 6, 9, 12, 18, 24, 36, 48, 54

OFDM Transmit and

receive 4.9 to 5.875

range

802.11b/g 1, 2, 5.5, 11 CCK

6, 9, 12, 18, 24, 36, 48, 54

OFDM

Transmit and

receive 2.4 to 2.5 ISM

range

Introduction

Wall Mount.

Above Ceiling Mount.

The LED indicators display connection status and error conditions, as well as

network activity for each of the two radios. Operation is as follows:

Start-up:

Radio Port Startup occurs immediately following the application of PoE

power, or following a power or software reset.

1. Both GREEN and AMBER LEDs light steadily for several seconds while

the Radio Port performs an internal self-test.

2. The AMBER LED then flashes 3 times per second, while the GREEN LED

is off. This indicates that the Radio Port is attempting to communicate to

a compatible wireless services-enabled switch.

3. Both LEDs then go off for a moment, followed by both LEDs lighting

steadily for a few seconds.

RSMA Antenna Connectors

2.4 Ghz Primary5 Ghz Primary

2.4 Ghz Secondary5 Ghz Secondary

RSMA Antenna Connectors

LEDs

Top View

Installation Instructions

4. After this sequence, assuming no error conditions have occurred, the

Radio Port will enter Normal operation mode. This means that the Radio

Port has successfully communicated with and been adopted by a wireless

services-enabled switch. If this startup sequence repeats itself, then it is

likely that the Radio Port is unable to contact a compatible wireless

services -enabled switch, and the installer should review the Trouble-

shooting section below.

Normal Operation:

Once the Radio Port has established a connection to a compatible wireless

services-enabled switch the Radio Port will begin normal operation. During

normal operation, the GREEN LED indicates status of the 802.11 b/g radio,

and the AMBER LED indicates status of the 802.11a radio.

■Without Wireless Traffic: Each LED will briefly flash once every 5 seconds,

to indicate that power is on, and the Radio Port is communicating nor-

mally to its wireless services-enabled switch. The flashing may not be

synchronous between the two LED indicators.

■With Wireless Traffic: Each LED will briefly flash more frequently than

once every 5 seconds, and in an irregular fashion, to represent traffic on

that radio.

Radio Error Mode:

■The GREEN LED flashes on and off steadily once per second if an error

prevents the 802.11b/g radio from operating normally.

■The AMBER LED flashes on and off steadily once per second if an error

prevents the 802.11a radio from operating normally.

Installation Instructions

The ProCurve Radio Port 220 can be mounted either on a wall or other

mounting point, or above a suspended ceiling. This Radio Port is not designed

for mounting on a desk.

To prepare for installation, perform the following steps:

1. Review site survey and network analysis reports to determine the location

and mounting position for the ProCurve Radio Port 220. Verify the

recommended external antenna type and antenna mounting configura-

tion.

2. Match the Radio Port model number on the purchase order with the model

numbers in the packing list and on the case of the device shipped.

Installation Instructions

3. Verify that the contents of the box include the intended ProCurve Radio

Port 220 and mounting hardware:

4. Verify that you have the recommended external antenna model and type

for the desired installation. External antennas must be purchased sepa-

rately. For a list of Supported Antennas for this Radio Port, see 'Supported

Antennas' below.

5. Connect a CAT-5 cable to a compatible 802.3af power source and run the

cable to the installation site. Ensure that there is sufficient slack on the

cable to perform the installation steps.

Radio Port Item Notes

220 J9005A 802.11a & 802.11b/g radios with external connectors.

This radio port is configurated with two pairs of

RSMA connectors

Andere Handbücher für procurve radio port 220

Inhaltsverzeichnis

Andere HP Netzwerk-Hardware Handbücher

HP c-Class Installationsanleitung

HP X1600 - StorageWorks Network Storage System 5.4TB SAS Model NAS... Bedienungsanleitung

HP BladeSystem C-Class Interconnect Component Gebrauchsanweisung

HP X1600 - StorageWorks Network Storage System 5.4TB SAS Model NAS... Anleitung zur Verwendung

HP JG602A Bedienungsanleitung

HP X1600 - StorageWorks Network Storage System 5.4TB SAS Model NAS... Bedienungsanleitung

HP UPS Network Module Bedienungsanleitung

HP ProCurve Networking J8451A Bedienungsanleitung

HP Edgeline EL1000 Bedienungsanleitung

HP ProLiant DL980 G7 Kurzanleitung

HP X1800sb G2 Gebrauchsanweisung

HP IBRIX X9000 Bedienungsanleitung

HP FF 12910 Montageanleitung

HP ProCurve Secure Router 7203dl J8753A J8753A Bedienungsanleitung

HP AJ878A - StorageWorks 320 GB Hard Drive Bedienungsanleitung

HP StorageWorks AB466A Bedienungsanleitung

HP FF 12904E Montageanleitung

HP 4265B Service-Handbuch

HP MSR954 Series Montageanleitung

HP AJ878A - StorageWorks 320 GB Hard Drive Bedienungsanleitung

HP ProCurve Radio Port 210 Montageanleitung

HP Aruba 640 Montageanleitung

HP StorageWorks HA-Fabric Manager Bedienungsanleitung

HP A3550A - High Availability Disk Arrays Model 20 Storage... Bedienungsanleitung

Beliebte Netzwerk-Hardware Handbücher anderer Marken

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Bedienungsanleitung

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Bedienungsanleitung

Yudor

Yudor YDS-16 Bedienungsanleitung

D-Link

D-Link ShareCenter DNS-320L Bedienungsanleitung

Samsung

Samsung ES1642dc Gebrauchsanweisung

Honeywell Home

Honeywell Home LTEM-PV Montageanleitung

evertz

evertz 7700 Series Bedienungsanleitung

D-Link

D-Link ShareCenter DNS-343 Bedienungsanleitung

Asante

Asante AsanteBridge 1012 Bedienungsanleitung

FireBrick

FireBrick FB2700 Bedienungsanleitung

Audiovox Electronics

Audiovox Electronics ARWH2T Bedienungsanleitung

ADC

ADC DSX-1 Handbuch

NetComm

NetComm NF2 Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 5620 Bedienungsanleitung

Dell EMC

Dell EMC XC6420 Series Bedienungsanleitung

Lanner

Lanner NCA-1020A Bedienungsanleitung

Allied Telesis

Allied Telesis AT-TN121-A Bedienungsanleitung

Lanner

Lanner NCA-1525 Bedienungsanleitung

HP procurve radio port 220 Bedienungsanleitung

Beliebte Netzwerk-Hardware Handbücher anderer Marken