HP VS160 - StorageWorks DLT Tape Drive Betriebsanleitung

External drives - contents

Pre-Installation

Before you start page 3

Backup software and drivers page 5

Usage models page 7

Using the CD-ROM page 9

Installing the tape drive

Step 1: Check the SCSI connection page 11

Step 2: Check the drive’s SCSI ID page 13

Step 3: Attach SCSI cable page 15

Step 4: Attach power cable page 17

Step 5: Verify installation page 19

Using the tape drive

Your HP StorageWorks VS160 tape drive page 21

Use the correct media page 23

Diagnostic tools page 26

Optimizing performance page 27

Troubleshooting page 29

Understanding the LEDs page 34

Problems with cartridges page 38

Other sources of information page 39

dltvs160_master.fm Page 1 Monday, November 22, 2004 10:33 AM

December 2004

Part Number: A7570-96001

Hewlett-Packard Company makes no warranty of any kind with regard to this material,

including, but not limited to, the implied warranties of merchantability and fitness for a

particular purpose. Hewlett-Packard shall not be liable for errors contained herein or for

incidental or consequential damages in connection with the furnishing, performance, or use

of this material.

This document contains proprietary information, which is protected by copyright. No part of

this document may be photocopied, reproduced, or translated to another language without

the prior written consent of Hewlett-Packard. The information contained in this document is

subject to change without notice.

Microsoft®, MS-DOS®, MS Windows®, Windows®and Windows NT®are U.S.

registered trademarks of Microsoft Corporation.

DLTtape, the DLTtape logo, Super DLTtape and the Super DLTtape logo are trademarks of

Quantum Corporation registered in the U.S.A. and other countries.

Hewlett-Packard Company shall not be liable for technical or editorial errors or omissions

contained herein. The information is provided ”as is” without warranty of any kind and is

subject to change without notice. The warranties for Hewlett-Packard Company products are

set forth in the express limited warranty statements for such products. Nothing herein should

be construed as constituting an additional warranty.

Printed in the U.K.

Product Details

Write your tape drive details here so you can find them easily if you need them. The model name is on the

front of the drive and the product and serial numbers are on a label on the bottom of the drive.

Model (type of drive):

Model (number):

Serial (number):

Date purchased/installed:

SCSI ID:

dltvs160_master.fm Page 2 Monday, November 22, 2004 10:33 AM

Before you start

The HP StorageWorks VS160 tape drive is a high-capacity, high-performance streaming tape

drive. Before starting to install your tape drive, you should consider the following.

Which operating systems are supported?

HP StorageWorks VS160 drives can be connected to servers running under Windows®.

Refer to the “HP StorageWorks Tape Software Compatibility” topic on our World Wide Web

site (www.hp.com/go/connect) for more information about the operating system versions

that are supported.

How do I use the tape drive with my system?

Check the usage models on page 7. This shows how the HP StorageWorks VS160 tape drive

can be used in different system configurations; direct attach and network attach.

How do I connect the drive to my server?

Your tape drive is supplied with a 68-pin, wide, VHDCI-to-HD SCSI cable to attach to the host

server. You will need a properly installed and configured SCSI host bus adapter (HBA) or a

built-in SCSI controller on your server with a spare LVDS SCSI port with a 68-pin, very high

density (VHDCI), wide SCSI connector.

For optimum performance your tape drive should only be connected to an Ultra 160 or Ultra

320 host bus adapter or SCSI controller and it should be the only device on the SCSI bus. Do

not connect more than two tape drives per SCSI controller. Do not attach the drive to the same

SCSI bus as your disk drive or RAID controller, unless it is a ProLiant server with a Smart Array

6i RAID controller.

See also Table 1, “supported SCSI bus types,” on page 11.

Why is the SCSI bus type important?

The SCSI bus type determines the speed at which data can be transferred between devices on

the bus and the maximum length of cable that can be used. HP StorageWorks VS160 tape

drives are high performance Ultra 160 SCSI devices with a maximum burst transfer speed of

160 MB/second. To benefit from this level of performance, it is important to ensure that the

drives are connected to a SCSI bus of a similar or higher specification. This means that you

need:

•An Ultra 160 or Ultra 320 SCSI bus. Ultra 160 SCSI supports the maximum bus speed of

160 MB per second; Ultra 320 SCSI exceeds this.

•LVD-rated SCSI cabling and terminators. The LVD interface and cable enables the data to

be transferred at the drive's maximum rate and provides a maximum cable length of 12

meters.

If you attach the drive to a lower specification SCSI bus, it may still work, but data will not be

transferred as quickly. For example, on a single-ended (SE) Ultra 2 SCSI bus the maximum

burst transfer speed of the drive is 40 MB/second and the maximum cable length is restricted

to 3 meters. See also Table 1, “supported SCSI bus types,” on page 11.

Note The drives are not compatible with high voltage differential (HVD) SCSI devices.

dltvs160_master.fm Page 3 Monday, November 22, 2004 10:33 AM

How can I check the SCSI bus type?

We strongly recommend that you use HP Library & Tape Tools to check your server’s current

SCSI configuration. This will provide information about the SCSI bus and the SCSI IDs in use.

HP Library & Tape Tools is the recommended diagnostic and support tool for your HP tape

storage product. It is available as a free download from the HP web site and is supported on

nearly all major operating systems.

See www.hp.com/support/tapetools for compatibility information, updates and the

latest version of the tool.

Do I need additional items for installation?

• If you do not have a VHDCI, wide SCSI connector on your server, you will need to purchase

and install a VHDCI-to-HD adapter or use an HD-to-HD cable instead of the supplied cable.

• If the tape drive is not the only or last device on the SCSI bus, you must terminate the bus

with a multimode terminator. If the tape drive is the only or last device on the bus, then the

tape drive enclosure provides active termination and you do not need to purchase a

separate terminator.

• If you do not have a spare, suitably rated SCSI connector on your server, a new HBA (also

known as a SCSI card) will be required. The SCSI bus rating should match or be higher than

the SCSI rating of your tape drive. See Table 1, “supported SCSI bus types,” on page 11

for recommended HBAs. For specific details relevant to your server model please refer to

www.hp.com/go/connect. You will need to purchase and install the new HBA into an

unused, 64-bit PCI expansion slot within your server before installing your tape drive. (The

kit can also be installed in a 32-bit PCI expansion slot, but performance may be degraded.)

Refer to our World Wide Web site for recommended products, configurations and ordering

information: www.hp.com/go/connect or www.hp.com/support/dlt.

dltvs160_master.fm Page 4 Monday, November 22, 2004 10:33 AM

Backup software and drivers

Backup software

For optimum performance it is important to use a backup application that is appropriate for

your system’s configuration. In a direct attach environment, where the tape drive is attached to

a standalone server, you can use backup software that is designed for a single server

environment. In network configurations you will need backup software that supports enterprise

environments. HP, Veritas, Legato, Yosemite and Computer Associates all provide suitable

products. Further details about these and other products that may be appropriate can be

found on our connectivity web site.

1Go to our connectivity web site: www.hp.com/go/connect and select tape backup.

2Select software compatibility.

3Select your combination of operating system and tape drive model in the table. A list of

supported backup applications is displayed.

4Make sure you have a backup application that supports HP StorageWorks VS160 tape drives

and download any upgrades or patches, if required.

Drivers

Windows users

After you connect the tape drive, download the HP driver from our web site: www.hp.com/

support, see “Step 5: Verify installation” on page 19.

Refer to the accompanying README file for specific installation instructions for Windows

2000, Windows XP and Windows Server 2003 drivers.

Note: We recommend that you install drivers from the web rather than the Windows

Hardware Installation Wizard, because the HP drivers fully support the performance of your

tape drive.

dltvs160_master.fm Page 5 Monday, November 22, 2004 10:33 AM

Figure 1: usage models

tape

drive (B)

Direct attach - SCSI Network attach - SCSI

storage server (A)

RAID disk subsystem

recommended, see

page 7

dltvs160_master.fm Page 6 Monday, November 22, 2004 10:33 AM

Usage models

The tape drive (B) can be used in a standalone or network environment. In a network

environment, anything less than Gigabit Ethernet may limit performance. The tape drive

should always be directly attached to a VHDCI SCSI connector on the storage server (A), as

shown in Figure 1.

A RAID disk subsystem is recommended. A single disk, particularly a fast disk such as a 15K

RPM drive, will also be sufficient, but be aware of other factors that can affect performance—

such as, compressibility of data, disk fragmentation and the number of files. You can use our

free performance assessment tools, which are available standalone or integrated into HP

Library & Tape Tools, to check tape performance and test whether your disk subsystem can

supply data at the optimum transfer rate. You can also use these tools to calibrate your restore

performance and maximal tape performance with more compressible data. See also

“Optimizing performance” on page 27.

Other models

The tape drive may work with other usage models, such as network attach storage (NAS) and

storage area networks (SAN), but HP does not currently provide technical support for

installing and using standalone DLT VS160 tape drives with these architectures. Similarly,

connection to fibre channel may be possible, if you purchase and install a fibre channel/SCSI

bridge, but it is not currently a supported option.

Please check www.hp.com/go/connect for the latest supported configurations.

dltvs160_master.fm Page 7 Monday, November 22, 2004 10:33 AM

install your

product

buy media

online

troubleshoot

with L&TT

learn about your

product

Figure 2: the

HP StorageWorks Tape

CD-ROM

dltvs160_master.fm Page 8 Monday, November 22, 2004 10:33 AM

Using the CD-ROM

The HP StorageWorks Tape CD-ROM is a central source of information about your tape drive

with utilities for getting the best performance from your tape drive.

Use the HP StorageWorks Tape CD-ROM to check installation, as described in this guide, and

to verify and troubleshoot performance after installation. It helps you to:

• Install your product, which includes access to drivers, an installation check, and

performance information and tools

• Learn about your product

• Register your product

•Buymediaonline

• Troubleshoot with HP Library & Tape Tools.

dltvs160_master.fm Page 9 Monday, November 22, 2004 10:33 AM

Figure 3: checking the VHDCI SCSI connection

connecting to an HBA

card in the server

dltvs160_master.fm Page 10 Monday, November 22, 2004 10:33 AM

Andere Handbücher für VS160 - StorageWorks DLT Tape Drive

Inhaltsverzeichnis

Andere HP Lagerung Handbücher

HP Brio 71xx Bedienungsanleitung

HP StorageWorks 2000fc Bedienungsanleitung

HP Colorado 5GB Bedienungsanleitung

HP StorageWorks 7110 - Virtual Array Bedienungsanleitung

HP C2488A Produkthandbuch

HP P9000 Bedienungsanleitung

HP NetStorage 6000 Bedienungsanleitung

HP EVA P6000 Kurzanleitung

HP 3000 - 37XE System Bedienungsanleitung

HP MSA 2050 Bedienungsanleitung

HP LTO-4 Ultrium 1760 Produkthandbuch

HP SimpleSave Bedienungsanleitung

HP SCSI Ultra320 Installationsanleitung

HP A5585A - SureStore DLT E Tape Library 4/40 Handbuch

HP StorageWorks 8B - FC Entry Switch Bedienungsanleitung

HP StorageWorks 4400 Bedienungsanleitung

HP 3PAR StoreServ 7200 2-node Bedienungsanleitung

HP StorageWorks 1000 - Modular Smart Array Gebrauchs- und Pflegehandbuch

HP STOREEVER LTO 4 Bedienungsanleitung

HP AU183AA - 2TB Personal Media Drive Gebrauchs- und Wartungshandbuch

HP Surestore 64 - Director Switch Bedienungsanleitung

HP StorageWorks MSA 2/8 - SAN Switch Bedienungsanleitung

HP 3PAR StoreServ 7200 2-node Gebrauchs- und Pflegehandbuch

HP P2000 G3 Bedienungsanleitung

Beliebte Lagerung Handbücher anderer Marken

QNAP

QNAP TS 32PXU Series Bedienungsanleitung

LaCie

LaCie RUGGED RAID Bedienungsanleitung

Freecom

Freecom CLS DOCK Bedienungsanleitung

PNY

PNY Attache P-FD64MBATT3 Bedienungsanleitung

OLT

OLT 6x6 Maximizer Bedienungsanleitung

Transcend

Transcend JetFlash 160 Bedienungsanleitung

LaCie

LaCie RUGGED MINI Bedienungsanleitung

Thunderbolt

Thunderbolt 600 Bedienungsanleitung

Panasonic

Panasonic LB-DH8 series Handbuch

Intel

Intel RAID High Availability Bedienungsanleitung

LaCie

LaCie 12big Thunderbolt 3 Bedienungsanleitung

Spectra Logic

Spectra Logic T-Series Spectra T50e Bedienungsanleitung

Panasonic

Panasonic LKM-F931-1 Bedienungsanleitung

Tabernus

Tabernus Enterprise Erase E2400 Bedienungsanleitung

Rocstor

Rocstor COMMANDER 3F series Bedienungsanleitung

Western Digital

Western Digital Ultrastar Data60 Bedienungsanleitung

Dell

Dell PowerVault MD3600f Series Bedienungsanleitung

CFI

CFI TERA STOR SATA RAID IV Bedienungsanleitung