HP 527 Bedienungsanleitung

The HP 527 is a Wi-Fi Alliance authorized Wi-Fi CERTIFIED

802.11a/b/g/n/ac product. The Wi-Fi CERTIFIED Logo is a certification

mark of the Wi-Fi Alliance.

HP 527 Dual Radio 802.11ac Unified Wired-WLAN

Walljack quick start guide

This quick start guide shows you how to install and get started using the HP 527 Dual

Radio 802.11ac Unified Wired-WLAN Walljack (RMN BJNGA-FB0005) JH048A

(AM), JH049A (WW), JH050A (JP), JH051A(IL), JH052A (20 pack AM), JH053A (20

pack WW), hereafter referred to as the HP 527.

Hardware overview

Back view

1: Pass Through port

2: Uplink port

Front view

Bottom views

3: GigabitEthernet LAN ports 1 and 2

4: PoE Out GigabitEthernet LAN port 3

5: Pass Through port

1 2

345

Package contents

The HP 527, mounting bracket, screws, MAC address label, and documentation.

Ports

Three Gigabit Ethernet ports: Auto-sensing 1000Base-T Ethernet ports with RJ-45

connectors.

One Gigabit Ethernet uplink port: Auto-sensing 1000Base-T Ethernet port with RJ-

45 connector.

One pair of pass-through ports: Work with Cat5 cabling as well as an analog

telephone cable.

Radio and antennas

The HP 527 supports IEEE 802.11a/b/g/n/ac. It has two internal antennas

supporting 2x2 MIMO with two spatial streams at a rate of up to 850 Mbps.

Reset button

The reset button is accessible through a hole on the side panel of the HP 527. To reset

the HP 527, insert a paper clip into the reset button hole, and press and quickly

release the button. To reset the HP 527 to factory defaults, press and hold the button

more than 5 seconds until the status LEDs (Power, Radio, and Uplink) flash, then

release.

Status LEDs

Status LEDs power

PoE Out

Uplink

LAN ports 1, 2, and 3

Radio

Power Uplink Radio LAN (1 to 3) PoE Description

Off Off Off Off Off The AP has no power.

Steady orange Off Off Off Off

Power applied. If the

power LED remains orange

after several minutes, the

AP failed to load the

software.

Green, flashing

every 2 seconds

(0.5Hz)

Off Off Off Off The AP is starting up.

Green, flashing

every 2 seconds

(1Hz)

Off Off Off Off

The AP is looking for an IP

address or building the list

of VLANS on which to

perform discovery.

The power, uplink, and radio LEDs are

flashing green in sequence. Off Off

The AP has obtained an IP

address and is attempting

to discover a controller.

Steady green

The uplink and radio

LEDs are flashing

reen alternately.

Off Off

The AP has found a

controller and is attempting

to establish a tunnel with it.

The power and uplink LEDs

are alternately flashing green

(slowly).

Off Off Off

The AP is performing

Ethernet negotiation, and

is waiting for the Ethernet

link to come up.

Steady green Off Any Any Any

The uplink interface is not

connected or there is no

network activity.

Steady green Flashing

green Any Any Any

The uplink interface is

active on a valid

1000Mbps link.

Steady green Flashing

orange Any Any Any

The uplink interface is

active on a valid 100Mbps

link.

Steady green Any Off Any Any

The radio interfaces are

disabled or there is no

network activity.

Steady green Any Flashing

green Any Any

Only the 2.4GHz radio

interface is transmitting or

receivin

data.

Steady green Any Flashing

orange Any Any

Only the 5GHz radio

interface is transmitting or

receivin

data.

Power Uplink Radio LAN (1 to 3) PoE Description

Steady green Any

Flashing

green

and

orange

alternatel

Any Any

Both 2.4GHz and 5GHz

radio interfaces are

transmitting or receiving

data.

Steady green Any Any Off Any

The uplink interface is

disabled or there is no

network activity.

Steady green Any Any Flashing green Any

The LAN interfaces are

active on a valid

1000Mbps link.

Steady green Any Any Flashing

orange Any

The LAN interfaces

are active on a valid

100Mbps link.

Steady green Any Any Any Off

No PoE device is

connected.

Steady

reen Any Any Any On A PoE device is connected.

Powering the HP 527

The HP 527 can be powered by using a local power source, an uninterruptible power

supply (UPS), a user-supplied power generator, or a PoE-enabled switch that provides

10/10 0 Mb p s or 10 / 100/ 10 0 0 Mbps Eth e rn e t ports.

Before you connect power to the AP, verify that the power supply is steady.

The HP 527 supports an 802.3af PoE PSE connection to one device on LAN port 3.

This feature is dependent on the power source of the HP 527, as follows:

Supports 802.3af class 1/2/3 PoE Out when the 803.3at (PoE+) power supply

mode is used.

Do not support PoE Out when the standard 803.3af power supply mode is used.

Important information to read before installing

Professional installation is required. For indoor installation only. Before installing or

using the AP, consult with a professional installer trained in RF installation and

knowledgeable in local regulations including building and wiring codes, safety,

channel, power, and license requirements for the intended country. The end user is

responsible for ensuring that installation and use comply with local safety and radio

regulations.

To avoid possible bodily injury or equipment damage, read the following safety

recommendations before you install an HP 527. The recommendations do not cover

every possible hazardous condition.

Install with six inches or more of clearance around the walljack.

Keep the chassis clean and dust-free.

Make sure the ground is dry and flat and anti-slip measures are in place.

Do not place the AP in a moist area and avoid liquid surrounding the AP.

Keep the chassis and installation tools away from walkways.

Installation

1. Place the mounting bracket, with the UP arrow pointing up, on the electrical

outlet box, and then use two of the supplied mounting screws to secure the

bracket to the box.

The two long mounting screws are for a US electrical box. The two short

mounting screws are for an EU electrical outlet box.

Long mounting screw Short mounting screw

Figure 1 Securing the mounting bracket to an electrical outlet box (EU)

Figure 2 Securing the mounting bracket to an electrical outlet box (US)

M3.5 × 25

2. Connect the network cable from the box to the RJ-45 Uplink port on the back of

the HP 527. If required, also connect the cable providing support for pass-

through devices to the Pass Through port on the back of the HP 527.

Figure 3 Connecting the network cable

3. Align the installation hole in the rear of the AP with the standout on the mounting

bracket.

Figure 4 Aligning the installation hole

4. Push the HP 527 onto the mounting bracket, and then slide it down until it is fully

engaged. Then secure the AP to the bracket by using the Phillips-head screw or

the security-head security Torx-10 screw.

Do not let go of the HP 527 until you confirm that it is securely in place.

Figure 5 Securing the AP

Provided access services

After the installation is complete, connect equipment to the HP 527 as follows:

Technical support

For worldwide technical support information, see the HP support website at

www.hp.com/networking/support.

Other regulatory information

For important safety, environmental, and regulatory information, see Safety and

Compliance Information for Server, Storage, Power, Networking, and Rack Products,

available at www.hp.com/support/Safety-Compliance-EnterpriseProducts.

FCC Notice

This device must not be co-located with any other transmitters except in accordance

with FCC multi-transmitter product procedures.

Printer Laptop

Phone

IP Phone

PoE Switch

IP TV

Pass Through

Andere Handbücher für 527

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere HP Drahtloser Zugangspunkt Handbücher

HP Vectra 525 Bedienungsanleitung

HP WL520 Bedienungsanleitung

HP Pavilion 501 Bedienungsanleitung

HP Aruba AP-375 Montageanleitung

HP MSM422 Bedienungsanleitung

HP Aruba AP-587 Montageanleitung

HP E-MSM466 Montageanleitung

HP 500R Series Bedienungsanleitung

HP MSM310-R Bedienungsanleitung

HP aruba AP-375ATEX Series Benutzerhandbuch

HP 425 - Notebook PC Bedienungsanleitung

HP 530 - Notebook PC Programmierhandbuch

HP MSM320-R Bedienungsanleitung

HP 560 Series Bedienungsanleitung

HP P 1981 A Bedienungsanleitung

HP Compaq Presario,Presario 650 Bedienungsanleitung

HP ProCurve RSVLC-0501 Bedienungsanleitung

HP 425 802.11n Bedienungsanleitung

HP ProCurve 530 WW Montageanleitung

HP ProCurve 530 NA (J8986A) Bedienungsanleitung

HP ProCurve 420 Bedienungsanleitung

HP MSM310 Anleitung zur Verwendung

HP MSM410 Bedienungsanleitung

HP Aruba AP-577 Montageanleitung

Beliebte Drahtloser Zugangspunkt Handbücher anderer Marken

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Bedienungsanleitung

Ubiquiti

Ubiquiti NanoStation NSM2 Bedienungsanleitung

Cisco

Cisco Aironet 1550 Series Bedienungsanleitung

Aruba

Aruba IAP-335 Bedienungsanleitung

Advantek Networks

Advantek Networks AWN-AP-54MR Bedienungsanleitung

IP-COM

IP-COM AP355 Bedienungsanleitung

Buffalo

Buffalo AirStation WLA-L11G Bedienungsanleitung

EnGenius

EnGenius EnStationACv2 Bedienungsanleitung

D-Link

D-Link DAP-3662 Bedienungsanleitung

Widelink

Widelink ezWave WAP-1100 Series Bedienungsanleitung

Edimax

Edimax CAP1200 Bedienungsanleitung

xG Technology

xG Technology xMax CN1300 Bedienungsanleitung

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Bedienungsanleitung

Aruba

Aruba AP-203R Bedienungsanleitung

LuXout Shades

LuXout Shades LUXSHADE MOTION Bedienungsanleitung

CreatComm

CreatComm TB5F Bedienungsanleitung

SineDigital

SineDigital MW-1500AP(H) Bedienungsanleitung

TP-Link

TP-Link AP9650 V1 Bedienungsanleitung