HP Aruba 570 Series Bedienungsanleitung

Aruba 570 Series Outdoor Access Points

Installation Guide

Rev 03 | May 2023 1

The Aruba 570 Series outdoor wireless access points (AP-574, AP-575 and AP-577) are high-performance, multi-

radio wireless devices that can be deployed in either controller-based (ArubaOS) or controllerless (Aruba Instant)

network environment.

The Aruba 570 Series access points support IEEE 802.11ax standard, delivering high performance with the MU-

MIMO (Multi-User Multiple-Input, Multiple-Output) technology, while also supporting 802.11a/b/g/n/ac wireless

services.

Package Contents

570 Series access point

Cable gland x 2

USB Type-C console cable x 1

Grounding lug and M4x6 screw x 1

Tools Required

Phillips screwdriver (#2 for M4x6 screw)

Flat blade screwdriver (Ethernet cable gland covers)

8mm allen or hex key (USB console cover)

The weatherproof caps for Ethernet and Console interfaces are connected to the access point, not loose in the

package.

Mounting kits for use with the 570 Series access points are sold separately. Contact your Aruba sales

representative for details.

Inform your supplier if there are any incorrect, missing, or damaged parts. If possible, retain the carton,

including the original packing materials. Use these materials to repack and return the unit to the supplier if

needed.

2Aruba 570 Series Outdoor Access Points | Installation Guide

Hardware Overview

Figure 1 AP-574 Front View (with Aesthetic Cover)

Figure 2 AP-574 Rear View (with Aesthetic Cover)

The antenna connectors of AP-574 are covered by an aesthetic cover. The aesthetic cover can be removed

when necessary.

USB Console Port

& Reset Button

System LED

Grounding Point E0

Aruba 570 Series Outdoor Access Points | Installation Guide 3

Figure 3 AP-575 Front View

Figure 4 AP-575 Rear View

USB Console Port

& Reset Button

Grounding Point

System LED

4Aruba 570 Series Outdoor Access Points | Installation Guide

Figure 5 AP-577 Front View

Figure 6 AP-577 Rear View

USB Console Port

& Reset Button

System LED

Grounding Point E0

Aruba 570 Series Outdoor Access Points | Installation Guide 5

External Antenna Connectors

The AP-574 access point is equipped with six external antenna connectors. The connectors are labeled 2G0, 2G1,

5G0, 5G1, 5G2, and 5G3.

Figure 7 AP-574 Bottom View (without Aesthetic Cover)

LED

The 570 Series access point is equipped with one LED that indicates the system status of the access point.

External antennas for this device must be installed by an Aruba Certified Mobility Professional (ACMP) or other

Aruba-certified technician, using manufacturer-approved antennas only.

The Equivalent Isotropically Radiated Power (EIRP) levels for all external antenna devices must not exceed the

regulatory limit set by the host country/domain.

Installers are required to record the antenna gain for this device in the system management software.

Les antennes externes pour cet appareil doivent être installées par un professionnel de la mobilité certifié Aruba

(ACMP) ou un autre technicien certifié Aruba, en utilisant uniquement des antennes approuvées par le fabricant.

Les niveaux équivalents de puissance à rayonnement isotrope (EIRP) pour tous les périphériques d'antenne

externe ne doivent pas dépasser la limite réglementaire définie par le pays hôte / domaine.

Les installateurs doivent enregistrer le gain d'antenne pour cet appareil dans le logiciel de gestion du système.

6Aruba 570 Series Outdoor Access Points | Installation Guide

Table 1 570 Series LED Meanings during Boot Up

Table 2 570 Series LED Meanings during Operation

Ethernet Ports

The 570 Series access points are equipped with two Ethernet ports (E0 and E1):

E0 port: 100/1000/2500Base-T auto-sensing MDI/MDX wired RJ45 network connectivity port

E1 port: 100/1000Base-T auto-sensing MDI/MDX wired RJ45 network connectivity port

Power

Both E0 and E1 ports support PoE-in, allowing the AP to draw power from an 802.3at/802.3bt PoE power source.

When the AP is powered by both E0 and E1 ports simultaneously, the AP can be configured by management

software to source PoE power from either port, or to combine power from both ports.

The 570 Series access points support the Intelligent Power Monitoring (IPM) feature, to report AP power

consumption and enable intelligent management of power-save capabilities.

Table 3 lists operational restrictions when the AP is powered by different power options.

Table 3 Power Options and Operational Restrictions

LED Color/State Meaning

System LED Off No power to AP

Red Initial power-up

Green - Flashing AP booting, not ready

Green - Steady AP ready and Gigabit Ethernet connected. The LED turns off after

1200 seconds

Green - Yellow, 6 seconds

period

AP ready and 10/100Mbps Ethernet link established. The LED

turns off after 1200 seconds

LED Color/State Meaning

System LED Solid Red General fault - Immediate attention required

One blink off every 3

seconds

Radio 0 fault (5 GHz)

Two quick blink off 0.5

seconds apart cycled every

3 seconds

Radio 1 fault (2.4GHz)

Power Source IPM Restrictions

1 x 802.3bt PoE n/a No restrictions, all capabilities available.

2 x 802.3at PoE n/a No restrictions, all capabilities available.

1 x 802.3at PoE enabled AP starts up in unrestricted mode, but may dynamically

apply restrictions depending on the PoE budget and actual

power.

1 x 802.3at PoE disabled Second (other) Ethernet port disabled.

1 x 802.3af PoE n/a AP does not start up, red system LED.

Aruba 570 Series Outdoor Access Points | Installation Guide 7

Grounding Point

Always remember to protect the access point by installing grounding lines. The ground connection must be

complete before connecting power to the access point enclosure.

USB Type-C Console Port

Use the included USB Type-C console cable to connect the access point to a laptop or a serial terminal for direct

management.

Reset Button

The reset button can be used to reset the access point to factory default settings or turn off/on the LED display.

There are two ways to reset the access point to factory default settings:

Reset the AP during normal operation

Press and hold down the reset button using a small, narrow object such as a paper clip for more than 10 seconds

during normal operation.

Reset the AP while powering up

1. Press and hold down the reset button using a small, narrow object such as a paper clip while the access point

is not powered on via PoE.

2. Connect the power supply (PoE) to the access point while the reset button is being held down.

3. Release the reset button on the access point after 15 seconds.

To turn off/on the LED display, press and release the reset button using a small, narrow object, such as a

paperclip for less than 10 seconds during normal operation of the access point.

Before You Begin

Refer to the sections below before beginning the installation process.

Pre-Installation Checklist

Before installing your 570 Series access point, be sure that you have the following:

Cat5E or better UTP cable with network access

A compatible PoE injector with power cord

One of the following network services:

Aruba Discovery Protocol (ADP)

DNS server with an “A” record

DHCP Server with vendor specific options

You need a proper 8mm allen or hex key to open the cover of the USB Console port.

FCC Statement: Improper termination of access points installed in the United States configured to non-US

model controllers will be in violation of the FCC grant of equipment authorization. Any such willful or

intentional violation may result in a requirement by the FCC for immediate termination of operation and may

be subject to forfeiture (47 CFR 1.80).

Aruba, in compliance with governmental requirements, has designed the 570 Series access points so that only

authorized network administrators can change configuration settings. For more information about AP

configuration, refer to the AP Software Quick Start Guide.

8Aruba 570 Series Outdoor Access Points | Installation Guide

Outdoor Planning and Deployment Considerations

Prior to deploying an outdoor wireless network, the environment must be evaluated to plan for a successful

WLAN deployment. Successfully evaluating the environment enables the proper selection of routers and

antennas and assists in the determination of their placement for optimal RF coverage. This process is considered

WLAN or RF planning and Aruba’s system engineers can assist in the outdoor planning process.

Identifying Specific Installation Locations

Use the access point placement map generated by Aruba RF Plan software application to determine the proper

installation location(s). Each location should be as close as possible to the center of the intended coverage area

and should be free from obstructions or obvious sources of interference. These RF absorbers/reflectors/

interference sources will impact RF propagation and should be accounted for during the planning phase and

adjusted for in RF plan.

Identifying Known RF Absorbers/Reflectors/Interference Sources

Identifying known RF absorbers, reflectors, and interference sources while in the field during the installation

phase is critical. Make sure that these sources are taken into consideration when you attach an access point to its

fixed location.

RF absorbers include:

Cement/concrete—Old concrete has high levels of water dissipation, which dries out the concrete, allowing

for potential RF propagation. New concrete has high levels of water concentration in the concrete, blocking

RF signals.

Natural Items—Fish tanks, water fountains, ponds, and trees

Brick

RF reflectors include:

Metal Objects—Metal pans between floors, rebar, fire doors, air conditioning/heating ducts, mesh windows,

blinds, chain link fences (depending on aperture size), refrigerators, racks, shelves, and filing cabinets.

Do not place an access point between two air conditioning/heating ducts. Make sure that access points are

placed below ducts to avoid RF disturbances.

RF interference sources include:

Microwave ovens and other 2.4 or 5 GHz objects (such as cordless phones)

Cordless headset such as those used in call centers or lunch rooms

Access Point Installation

Access points are radio transmission devices and as such are subject to governmental regulation. Network

administrators responsible for the configuration and operation of access points must comply with local

broadcast regulations. Specifically, access points must use channel assignments appropriate to the location in

which the access point will be used.

The rules for the 5600-5650 MHz band vary by region.

Use of this equipment adjacent to or stacked with other equipment should be avoided because it could result in

improper operation. If such use is necessary, this equipment and the other equipment should be observed to

verify that they are operating normally.

Service to all Aruba products should be performed by trained service personnel only.

Aruba 570 Series Outdoor Access Points | Installation Guide 9

Using Mount Kits

The 570 Series access point can be installed on a wall or attached to a pole by using mount kits:

Grounding the Access Point

The grounding must be completed before powering up the access point. The grounding wire should be #8 AWG.

1. Peel the cover of one end of the grounding wire and place the bare grounding wire into the grounding lug

(included in the package), and press firmly with the crimping pliers.

2. Fasten the grounding lug to the grounding hole on the access point with the screw (included in the package).

Connecting the Ethernet Cable

To connect the Ethernet cable to the access point, perform the following steps using the Ethernet cable glands

that ships with your access point.

Table 4 Applicable Mount Kits for 570 Series Access Point

Part Number Description

JW052A AP-270-MNT-V1 long mount kit for wall and vertical pole mounting, 300 mm from

vertical mounting asset.

JW053A AP-270-MNT-V2 short mount kit for wall and vertical pole mounting, 75 mm from

vertical mounting asset.

JW054A AP-270-MNT-H1 mount kit for hanging from inclined or horizontal structure.

JW055A AP-270-MNT-H2 flush mount kit for wall and ceiling mounting.

The 570 Series access point does not ship with any mount kits. These mount kits are available as accessories

and must be ordered separately.

For installation instructions on AP-270-MNT-V1, AP-270-MNT-V2, AP-270-MNT-H1 and AP-270-MNT-H2 mount

kit, please refer to the AP-270-MNT-V1 Installation Guide, AP-270-MNT-V2 Installation Guide, AP-270-MNT-H1

Installation Guide and AP-270-MNT-H2 Installation Guide respectively.

Mounting instructions for the antennas for the AP-574 access points are provided with the antennas. The

mounting must be consistent with the instructions provided to ensure compliance with US and Canadian

regulatory requirements when used outdoors.

This 570 Series access point is intended for installation in a RESTRICTED ACCESS LOCATION attached to a pole

or installed on a wall. Installers should disconnect power before working with or near the access point.

Failure to use the included Ethernet cable glands can lead to connectivity and POE issues.

The cable is not included and must be purchased separately. Purchase a suitable UV-resistant, outdoor rated,

CAT 5E or better RJ45 cable for use with the access point.

10 Aruba 570 Series Outdoor Access Points | Installation Guide

Figure 8 Installing the Ethernet Cable Gland

1. Remove the dust cap from the Ethernet port

2. Slide the sealing nut, clip, split grommet and gland body over the cable.

3. Insert the RJ45 connector to the Ethernet port.

4. Screw the gland body onto the Ethernet port.

5. Combine the two split parts of the grommet over the cable, and move it towards the gland body until it

locates at the recess of the gland body.

6. Move the clip towards the gland body, passing over the grommet, until the wavy end of the clip properly fits

into the wavy end of the gland body.

7. Screw the sealing nut onto the gland body.

Software

For instructions on choosing operating modes and initial software configuration, refer to the AP Software Quick

Start Guide.

Verifying Post-Installation Connectivity

The integrated LEDs on the access point can be used to verify that the access point is receiving power and

initializing successfully (see Table 1 and Table 2). Refer to the AP Software Quick Start Guide for further details

on verifying post-installation network connectivity.

Electrical and Environmental Specifications

Electrical

Ethernet

E0: 100/1000/2500Base-T auto-sensing Ethernet RJ-45 Interfaces

E1: 100/1000Base-T auto-sensing Ethernet RJ-45 Interfaces

Power over Ethernet (IEEE 802.3at and 802.3bt compliant)

Environmental

Operating

Sealing Nut

Clip

Gland Body

Split Grommet

Two grommets are provided in the package for use with the Ethernet cables. One is applicable for cables with

4-6 mm diameter, and another is applicable for cables with 6-10 mm diameter.

Aruba access points are classified as radio transmission devices, and are subject to government regulations of

the host country. The network administrator(s) is/are responsible for ensuring that configuration and operation

of this equipment is in compliance with their country’s regulations. For a complete list of approved channels in

your country, refer to the Aruba Downloadable Regulatory Table at https://www.arubanetworks.com/techdocs/DRT/

Default.htm

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere HP Drahtloser Zugangspunkt Handbücher

Beliebte Drahtloser Zugangspunkt Handbücher anderer Marken

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Bedienungsanleitung

Ubiquiti

Ubiquiti NanoStation NSM2 Bedienungsanleitung

Cisco

Cisco Aironet 1550 Series Bedienungsanleitung

Aruba

Aruba IAP-335 Bedienungsanleitung

Advantek Networks

Advantek Networks AWN-AP-54MR Bedienungsanleitung

IP-COM

IP-COM AP355 Bedienungsanleitung

Buffalo

Buffalo AirStation WLA-L11G Bedienungsanleitung

EnGenius

EnGenius EnStationACv2 Bedienungsanleitung

D-Link

D-Link DAP-3662 Bedienungsanleitung

Widelink

Widelink ezWave WAP-1100 Series Bedienungsanleitung

Edimax

Edimax CAP1200 Bedienungsanleitung

xG Technology

xG Technology xMax CN1300 Bedienungsanleitung

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Bedienungsanleitung

Aruba

Aruba AP-203R Bedienungsanleitung

LuXout Shades

LuXout Shades LUXSHADE MOTION Bedienungsanleitung

CreatComm

CreatComm TB5F Bedienungsanleitung

SineDigital

SineDigital MW-1500AP(H) Bedienungsanleitung

TP-Link

TP-Link AP9650 V1 Bedienungsanleitung