HP MSM310 Anleitung zur Verwendung

5998-0557 5.3.5

MSM3xx / MSM4xx Access Points

5.3.5 Release Notes

Release Notes for the HP ProCurve MSM3xx / MSM4xx Access Points

Introduction

This document applies to these HP ProCurve MSM products:

(“USA” identifies USA versions, “WW” identifies worldwide versions for the rest of the world.)

Release 5.3.5 - - - - - - - - - - - - - - - - - - - - - - - - 2

Release 5.3.4 - - - - - - - - - - - - - - - - - - - - - - - - 8

Release 5.3.3 - - - - - - - - - - - - - - - - - - - - - - - - 9

Release 5.3.2 - - - - - - - - - - - - - - - - - - - - - - - 10

Release 5.3.1 - - - - - - - - - - - - - - - - - - - - - - - 11

Release 5.3.0 - - - - - - - - - - - - - - - - - - - - - - - 12

Model USA Japan WW

MSM310 Access Point J9374A/B J9524A/B J9379A/B

MSM310-R Access Point J9380A/B J9383A/B

MSM317 Access Device J9422A J9423A J9423A

MSM320 Access Point J9360A/B J9527A/B J9364A/B

MSM320-R Access Point J9365A/B J9528A/B J9368A/B

MSM325 Access Point with Sensor J9369A/B J9373A/B

MSM335 Access Point with Sensor J9356A/B J9357A/B

MSM410 Access Point J9426A/B J9529A/B J9427A/B

MSM422 Access Point J9358A/B J9530A/B J9359A/B

MSM3xx / MSM4xx Access Points 5.3.5 Release Notes 2HP ProCurve Networking

Release 5.3.5

Contents

General information - - - - - - - - - - - - - - - - - - - - - - - - - - - 2

Fixes - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3

Known issues - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 5

General information

Terminology

The following terminology is used in these Release Notes and other 5.3.x documentation as follows: .

Documentation

You can download documentation from the HP ProCurve Networking manuals Web page at:

www.hp.com/go/procurve/manuals.

Updating software

Customers with support contracts can obtain the latest software updates via Software Upgrade

Managers (SUM)

. For more information on this process, visit the HP Software Releases & Media

website at:

www.hp.com/softwarereleases/releases-media2/SUM/How_to_be_a_SUM_customer.htm.

Customers without support contracts who wish to obtain the latest software updates can purchase

a software Care Pack service by contacting their local HP sales representative or authorized HP

reseller.

(Not applicable to MSM317.)

For autonomous APs, update the software as described in the

Firmware updates

section of the

MSM3xx / MSM4xx Management and Configuration Guide

For controlled APs including the MSM317, update the service controller software as described in

the Firmware updates section of the MSM7xx Controllers Management and Configuration Guide.

Once the service controller is updated, it automatically updates all of its controlled devices to the

same software version.

Term Description

AP The term “access point” is generally abbreviated as AP.

Service controller Refers to the HP ProCurve MSM7xx Controllers.

MSM3xx / MSM4xx Access Points 5.3.5 Release Notes 3HP ProCurve Networking

Regulatory update

See also the regulatory information in the updated v5.3.5 Quickstarts available as described under

Documentation above.

REGULATORY NOTICE for European Union

As of July 1st 2010, all wireless devices sold in EU countries and any countries that participate in

the EU free market must meet stringent Dynamic Frequency Selection (DFS) requirements for

radar detection and avoidance (EN 301.893 v1.5.1). The MSM APs and the MSM7xx Controllers

used to control and configure them are compliant.

Other regulatory information

In the USA and Canada, no DFS channels are available on Radio 1 of the MSM422 even when

operating in legacy modes.

Sensors and RF Manager

Sensors (MSM320, MSM325, MSM335) at version 5.3.5 are ONLY compatible with RF Manager

version 5.9.203. If you choose not to upgrade to RF Manager 5.9.203, do not upgrade a Sensor

(directly, or via an MSM Controller) that will be used with RF Manager to version 5.3.5. See also

the MSM7xx Controllers Management and Configuration Guide.

Fixes

The following issue has been fixed since the previous release:

ID Description

42387 802.1X users may sometimes be unable to log in.

43076 (Applies to autonomous APs.) It is not possible to disable IGMP using the management

tool. The AP management tools displays a "page cannot be found" message and logs

the user out. As a work around, the following CLI command can be used to deactivate

IGMP:

no dot11 igmp snooping-helper

44396 The MSM710, MSM422, MSM335, and MSM410 may unexpectedly restart.

44894 L3 roaming may fail for wireless clients roaming between APs on different subnets and

VLANs.

44905 The CLI shows incorrect values for 802.11n multicast rate.

45142 The automatic channel selection feature may cause excessive channel switching in

environments where many APs are on the same channel.

45239 802.1X client stations are not deauthenticated if the user does not enter login

credentials within a few minutes of receiving the login prompt. This can cause client

stations to be unable to login via 802.1X.

45542 Wireless protection for a VSC should be set to WPA2 or WPA+WPA2 to ensure the best

compatibility and performance with 802.11n clients.

45806 The MSM310 and MSM320 show too many wireless FCS RX errors on Radio 1.

MSM3xx / MSM4xx Access Points 5.3.5 Release Notes 4HP ProCurve Networking

46012 The CLI command show dot11 statistics client-traffic does not display the correct

information for 802.11 rates.

46019 An internal problem is causing messages similar to the following to appear in the log:

assert: retry.c IsTimeToRetry 52 (aRetryInfo->mRetryType ==

RETRY_TYPE_CONSTANT && aRetryInfo->mRetry.mInterval

46293 The ETSI DFS channels for EU countries are not permitted and have been removed for

all revision B products with CM9 radio. See also the MSM Access Point Quickstarts.

46383 (MSM317 only.) In some cases the MSM317 may frequently lose connectivity with the

controller and fail to report statistics properly.

46512 The SNMP object “coDot11PktsRate54” shows only receive rates. Transmit rates are

missing.

46554 In some cases, 802.1X authentication may not work properly.

47634 (MSM410 only.) The MSM410 may stop advertising SSIDs with the following message

added to the system log:

ar5416GetPendingInterrupts: received PCI FATAL interrupt

47773 (MSM317 only.) The MSM317 restarts when trying to retrieve debugging information on

the Controlled APs > [AP] >> Tools > Debugging tools page.

47831 The antenna icons (which indicate the mode of operation for an AP) on the Controlled

APs >> Overview > Discovered APs page may intermittently disappear when the AP

is handling a large amount of wireless traffic.

47916 Under certain conditions, performance may be dramatically reduced for long periods of

time when clients use 802.11 power save mode.

47980 (MSM317 only.) If a switch port is configured with a VLAN, after a few days the VLAN is

lost and traffic gets sent untagged.

48057 (MSM317 only.) When the MSM317 is configured to support six or more VSCs, wireless

clients may be unable to connect to some of the VSCs.

48594 When fragmentation was required on a tunnel interface due to the MTU size limitation of

a tunnel, a “UDP loop detected” error was incorrectly being sent to the syslog.

48666 If you define a custom wireless security filter using the %g placeholder, it will not work

because the %g placeholder is not interpreted correctly by the AP.

50105 (MSM317 only.) If an MSM317 switch port has MAC authentication enabled, or is bound

to a VSC with MAC authentication enabled, after a few days, client stations are unable

to authenticate through the port.

50485 When handling a large amount of wireless traffic, an AP may lose its IP address and be

unable to get a new one from a DHCP server.

50806 Changing the time zone to GMT +8 on a controller results in APs not being able to

synchronize.

51473 (MSM317 only.) If the MSM317 Uplink port is connected to a network with a high traffic

load, the MSM317 may lose synchronization with the controller.

51940 Broadcast packets to or from a roaming client are sometimes dropped.

ID Description

MSM3xx / MSM4xx Access Points 5.3.5 Release Notes 5HP ProCurve Networking

Known issues

The following known issues are present in this release:

52009 (MSM422 only.) The MSM422 Ethernet port cannot be manually set to 1000 Mbps, even

though the product supports this rate. If you set the port to Auto however, it will operate

at 1000 Mbps when connected to another device operating at the that speed.

ID Description

33604 (Only MSM335 and MSM320/325.) The Wireless status light for a radio configured in

Sensor mode does not turn on. This is true even when the sensor is enabled and

operational.

34173 (Only MSM422.) When radio 1 is set to 802.11n (5GHz) and radio 2 is set to 802.11a,

and both are configured for local mesh, if one radio is set to a specific channel and the

other is configured for auto- channel, both radios can end up to be on the same channel.

Therefore, configure each radios for a specific (and different) channel or configure both

radios for auto-channel.

38305 (Only MSM317.) Making any configuration change on an MSM317 results in all wired

802.1X users erroneously having their connections terminated during the

synchronization process.

38621 (Only MSM317.)

Applies only when at least one non-access-controlled VSC is configured with

Ethernet Switch as the VSC ingress mapping, and one access controlled VSC is

configured with a VLAN as the VSC ingress mapping.)

This message may appear in the system log:

err confighandl Failed to read ingress VLAN information for Virtual Service

This message should be ignored.

38750 (Only MSM317.) The MSM317 may generate a CFG_SYNC_FAILURE in the log when

it synchronizes after a number of configuration changes have been made on the

controller. The MSM317 will then restart, apply all changes, and operate normally.

38984 When a third-party DHCP server is used to send alternate IP addresses for service

controller discovery using DHCP Option 43, discovery will fail if third-party options

appear in the list above the service controller IP addresses.

To avoid this problem, ensure that the service controller IP addresses option is the first

option in the list.

39804 When configuring the Allowed wireless rates option under Virtual AP in a VSC, the

user can disable support for all 802.11n data rates. If the VSC is only operating on

802.11n, then one non-MSC rate must remain operational or the VSC will not function

correctly.

39994 The Axis2 SOAP client toolkit has issues dealing with some SOAP responses.

MSM3xx / MSM4xx Access Points 5.3.5 Release Notes 6HP ProCurve Networking

45094 If the radio is set to operate in 802.11n/g mode, it continues to provide support for

802.11b mode. You can fix this behavior by removing support for the 802.11b modes in

each VSC (under Virtual AP > Allowed wireless rates).

48316 If there are more than 80 APs shown on the Neighbor page, the following message may

be logged: "Radio 1's node table is full. Too many nodes in the surroundings (max is

256)."

49182 Under a very heavy wireless load, wireless client traffic can become very slow after

several large file transfers. Terminating and reassociating client stations does not

resolve the issue. The only solution is to restart the AP.

52305 The online help for the CLI command "rcapture" is incorrect. The correct information is

as follows:

Syntax:

rcapture -u URI [-c count] -i interface

Description:

Capture data on a port and send it to a file on an FTP server.

Parameters:

URI: Address of the FTP site and file where the trace will be saved, for example:

ftp://user:[email protected]/trace.pcap

count: Number of packets to capture.

interface: Interface to trace, where:

eth0 = Internet port

eth1 = LAN port

wvlan0 = wireless port

52840 If you downgrade an AP from 5.3.5 to 5.3.1 and the AP is operating in controlled mode

with both radios set to 802.11a on a specific DFS channel, the AP will not be able to

synchronize with the controller. To enable the AP to synchronize, go to the radio page

and select auto channel or pick a non-DFS channel.

52846 When set to auto channel, and the radio picks a DFS channel, the unit will not scan a

different channel unless the auto channel interval is set.

52848 (MSM317 only.) If wired devices with static IP addresses are connected to the switch

ports, the devices are able to communicate with each other regardless of the type of

authentication that is enabled on the VSCs bound to the ports, as long as the ports have

the same VLAN or no VLAN (untagged).

53553 If you plan to connect APs (as slaves) to a controller via local mesh, the APs must first

be upgraded to the same software version that is running on the controller. For example,

APs running version 5.3.3 cannot connect to a controller as local mesh slaves when the

controller is running 5.3.5.

54095 If you define custom wireless security filters for a non-access-controlled VSC, they may

not be applied after the AP is restarted.

ID Description

MSM3xx / MSM4xx Access Points 5.3.5 Release Notes 7HP ProCurve Networking

54193 Revision B APs (J number ends with “B”) do not support 802.11a Turbo mode. Setting a

controlled AP to 802.11a Turbo mode and selecting DFS channel will cause the

configuration to be reset.

ID Description

MSM3xx / MSM4xx Access Points 5.3.5 Release Notes 8HP ProCurve Networking

Release 5.3.4

Fixes

The following issue has been fixed since the previous release:

ID Description

42885 (Applies when Auto Channel is being used.) APs attempt to re-allocate channels at the

same time. This has been corrected by introducing a more random behavior. The first

channel re-allocation will be done at a random time within plus or minus 50 percent of

the configured interval. For example, if the configured interval is 24 hours, the first re-

allocation will occur anytime within 12 to 36 hours, and subsequent allocations will be

done every 24 hours.

MSM3xx / MSM4xx Access Points 5.3.5 Release Notes 9HP ProCurve Networking

Release 5.3.3

Fixes

The following issues have been fixed since the previous release:

ID Description

43252 MAC Authentication does not support RADIUS assigned VLANs for wireless clients that

are not access controlled.

43594 (Only MSM422.) Radio 2 is has difficulty dealing with noise in the 2.4GHz range.

43726 (Only MSM410 and MSM422.) When the 802.11n radio Wireless mode is set to

802.11g (not 802.11n/g or 802.11n/b/g), and Automatic power control is enabled, the

radio stops transmitting.

43900 (Only MSM317.) The MSM317 reboots or does not operate correctly when seeing a

large number of stations on its Uplink port.

43949 (Only MSM410 and MSM422 with v5.3.2 software.) Legacy clients connected to an

802.11n radio will experience poor performance.

MSM3xx / MSM4xx Access Points 5.3.5 Release Notes 10 HP ProCurve Networking

Release 5.3.2

Fixes

The following issues have been fixed since the previous release:

ID Description

39248 802.1X WPA2 clients that do not have a valid value for the Descriptor Type field are not

able to connect.

39292 (Only MSM410 and MSM422 (MAP-625).) In environments with substantial wireless

interference, some client stations may experience low throughput when connected via

802.11n.

40332 Spanning Tree Protocol is not supported on the MSM317 switch ports.

40434 (Only MSM317.) Wireless throughput on higher channels may be reduced when the

transmission power is set to maximum.

41519 An AP with a valid sensor license will not report it to the controller, causing the controller

to wrongly flag the AP as having a "License violation."

42595 When both L3 mobility and WPA2 opportunistic key caching are enabled on a VSC, and

client stations frequently roam between several APs, the APs may unexpectedly restart.

Andere Handbücher für MSM310

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere HP Drahtloser Zugangspunkt Handbücher

HP MSM310 Bedienungsanleitung

HP 650 Series Bedienungsanleitung

HP aruba AP-375ATEX Series Benutzerhandbuch

HP ProCurve 420 Bedienungsanleitung

HP ProCurve Wireless Access Point 530 Bedienungsanleitung

HP MSM323-R Bedienungsanleitung

HP ProCurve 420 Bedienungsanleitung

HP 600R Series Bedienungsanleitung

HP J9650A Bedienungsanleitung

HP MSM320 Bedienungsanleitung

HP MSM335 Bedienungsanleitung

HP Aruba AP-587 Montageanleitung

HP HP417 Montageanleitung

HP ProCurve 420 Bedienungsanleitung

HP Pavilion 501 Bedienungsanleitung

HP Aruba AP-375 Montageanleitung

HP MSM422 802.11n Bedienungsanleitung

HP V-M200 Betriebsanleitung

HP MSM325 Bedienungsanleitung

HP J9845A Gebrauchsanweisung

HP 425 - Notebook PC Bedienungsanleitung

HP A-WA2610E-AGN Montageanleitung

HP MSM430 Bedienungsanleitung

HP WL520 Bedienungsanleitung

Beliebte Drahtloser Zugangspunkt Handbücher anderer Marken

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Bedienungsanleitung

Ubiquiti

Ubiquiti NanoStation NSM2 Bedienungsanleitung

Cisco

Cisco Aironet 1550 Series Bedienungsanleitung

Aruba

Aruba IAP-335 Bedienungsanleitung

Advantek Networks

Advantek Networks AWN-AP-54MR Bedienungsanleitung

IP-COM

IP-COM AP355 Bedienungsanleitung

Buffalo

Buffalo AirStation WLA-L11G Bedienungsanleitung

EnGenius

EnGenius EnStationACv2 Bedienungsanleitung

D-Link

D-Link DAP-3662 Bedienungsanleitung

xG Technology

xG Technology xMax CN1300 Bedienungsanleitung

Widelink

Widelink ezWave WAP-1100 Series Bedienungsanleitung

Edimax

Edimax CAP1200 Bedienungsanleitung

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Bedienungsanleitung

Aruba

Aruba AP-203R Bedienungsanleitung

LuXout Shades

LuXout Shades LUXSHADE MOTION Bedienungsanleitung

CreatComm

CreatComm TB5F Bedienungsanleitung

SineDigital

SineDigital MW-1500AP(H) Bedienungsanleitung

TP-Link

TP-Link AP9650 V1 Bedienungsanleitung