HUANUO HNCM7 Bedienungsanleitung

Desk Monitor Arm

INSTRUCTION

MANUAL

Rev00(A)

HNCM7

(US/CA) 1-800-556-0533

(UK) 44-808-196-3874

[email protected]

WWW. www.huanuo.com

02 03 04

05 06 07 08

09 10 11

12 13 14 15

16 17 18 19

20 21 22

17.6 lbs /

8kg

Before getting started,

let's make sure this mount is compatible.

Is the VESA

pattern of your

monitor 75 x 75mm

(3″ x 3″) to 100 x

100mm (3.9″ x 3.9″)?

Does your monitor

(including accessories)

weigh less than 17.6 lbs

(8kg) ?

Tools Needed

(NOT lncluded)

Yes - Perfect!

No - This mount is NOT

compatible.

Yes - Perfect!

No -This mount is NOT

compatible.

7/16 - 7/8″

(11 - 22mm)

Wood Drill Bit

3/8″ (10mm)

Wrench

Electric Drill

Phillips

Screwdriver

Important Safety

Information

· Avoid potential personal injuries and property damage!

· DO NOT use this product on desks made of particle board or other

soft woods.

· DO NOT use this product for any purpose that is NOT explicitly

speciﬁed in this manual. DO NOT exceed weight capacity. We are

NOT liable for damage or injury caused by improper mounting,

incorrect assembly or inappropriate use.

· Before starting assembly, verify all parts are included and

undamaged. DO NOT use damaged or defective parts. lf you require

replacement parts, please contact our technical support line at

1-800-556-0533 (US/CA) / 44-808-196-3874 (UK) or customer

service at [email protected].

· This product contains small parts that may pose a choking hazard.

NOTE

CAUTION

WARNING

· Please carefully read all instructions before attempting installation.

If you DO NOT understand the instructions or have any questions or

concerns, please contact our technical support line at

1-800-556-0533 (US/CA) / 44-808-196-3874 (UK) or customer

service at [email protected].

· Not all hardware included in this package will be used.

02 03 04

05 06 07 08

09 10 11

12 13 14 15

16 17 18 19

20 21 22

Contents

Locking Plate

[a] x 1 Bottom Pad

[b] x 1

Nut

[E2] x 1

Nut

[E3] x 2

3/16″ (5mm)

Large Allen Key

[F1] x 1

1/8″ (3mm）

Small Allen Key

[F2] x 1

M4 x 12mm

Bolt

[A] x 8

M4 x 30mm

Bolt

[B] x 8

L13mm

Spacer

[C] x 8

Washer

[D1] x 8

M8 X 8mm

Bolt

[E1] x 2

x 1

Pole

x 1

C-Clamp

Decorative Cover

[D2] x 1

x 1

Swivel Arm

x 2

VESA Plate

02 03 04

05 06 07 08

09 10 11

12 13 14 15

16 17 18 19

20 21 22

Option A:

For C Clamp Mounting

Step 1 Install the Base

0.4″- 3″

(10mm - 78mm)

02 03 04

05 06 07 08

09 10 11

12 13 14 15

16 17 18 19

20 21 22

Option B:

For Grommet Mounting

02a

NOTE: If there is no grommet hole on your desktop, mark a hole on your desired position

(Be sure to leave 2″ from the edge of the desktop). Drill a hole using a drill bit in the

diameter of 7/16-7/8″ (11-22mm).

≥2″ (50mm)

7/16 - 7/8″

(11 - 22mm)

7/16 - 7/8″

(11 - 22mm)

Remove the pre-assembled washer and bolt on the locking plate [a].

Phillips

Screwdriver

(Not lncluded)

Electric Drill

(Not lncluded)

0.4″- 3″

(10mm - 78mm)

02 03 04

05 06 07 08

09 10 11

12 13 14 15

16 17 18 19

20 21 22

Step 2 Secure the Swivel Arm [03] and Decorative Cover [D2] to

the Pole [01]

WARNING

CASE：If the head

is not straight.

Solution

Height Adjustment

① ② ③

NOTE: The bolt

should be directed

toward the top.

Slide the swivel extension arm [03] downwards to your desired height, and tighten the

nuts [F1] to hold the arm in place.

02 03 04

05 06 07 08

09 10 11

12 13 14 15

16 17 18 19

20 21 22

Select Monitor Bolts

Step 3 Attach the VESA Plates to the Monitors

Hand thread bolts into the threaded inserts on the back of your TV to determine which bolt

(M4 x 12mm or M4 x 30mm) to use. A minimum of 4-5 turns into the threading is required.

Do not turn past the bottom of the hole.

Option A (For Flat Back TVs)

M4 x 12mm

M4 x 30mm

02 03 04

05 06 07 08

09 10 11

12 13 14 15

16 17 18 19

20 21 22

Option B (For Curved TVs)

Step 4 Hang the Monitors on the Swivel Arm

3/8″ (10mm)

Wrench

(Not lncluded)

Hang the monitor on te head of the swivel arm using the hanging tab and nut [E3].

Tighten the nut [E3]. Make sure the nut is secured before you rotate the monitor.

02 03 04

05 06 07 08

09 10 11

12 13 14 15

16 17 18 19

20 21 22

Step 5 Alignment of Two Monitors

Remove the nut [E3] with wrench, then turn the bolt with small Allen key [F2] to raise

or lower the monitor. Then retighten the nut [E3] after adjustment. Individual monitor

height adjustment helps to perfectly align the monitors.

3/8″ (10mm)

Wrench

(Not lncluded)

NOTE: Ignore this step

if monitors are level.

Loosen Tighten

02 03 04

05 06 07 08

09 10 11

12 13 14 15

16 17 18 19

20 21 22

TiltTilt

The monitor should adjust easily when moved, then stay in place. Adjust the tilt tension

bolt [T] if your monitor naturally tilts up or down.

Step 6 Tilt Adjustment

Loosen

Tighten

02 03 04

05 06 07 08

09 10 11

12 13 14 15

16 17 18 19

20 21 22

Andere Handbücher für HNCM7

Inhaltsverzeichnis

Andere HUANUO Rack & Stand Handbücher

HUANUO

HUANUO HNFR3 Bedienungsanleitung

HUANUO

HUANUO HNSSK4 Programmierhandbuch

HUANUO

HUANUO HNCM18 Bedienungsanleitung

HUANUO

HUANUO HNDSK4 Bedienungsanleitung

HUANUO

HUANUO HNPS01 Bedienungsanleitung

HUANUO

HUANUO HNCM7 Bedienungsanleitung

HUANUO

HUANUO HNCM20 Bedienungsanleitung

HUANUO

HUANUO HACM1 Bedienungsanleitung

HUANUO

HUANUO HNDS8 Bedienungsanleitung

HUANUO

HUANUO HNDA1 Bedienungsanleitung

HUANUO

HUANUO HNDS11 Bedienungsanleitung

HUANUO

HUANUO HNCM16 Bedienungsanleitung

HUANUO

HUANUO HNCM12 Bedienungsanleitung

HUANUO

HUANUO HNCM9 Bedienungsanleitung

HUANUO

HUANUO HNHM4 Bedienungsanleitung

HUANUO

HUANUO HNSS7 Bedienungsanleitung

HUANUO

HUANUO HNCM3 Bedienungsanleitung

HUANUO

HUANUO HNLL3 Bedienungsanleitung

HUANUO

HUANUO HNCM1 Bedienungsanleitung

HUANUO

HUANUO HNTS3S Bedienungsanleitung

HUANUO

HUANUO HNCM7 Bedienungsanleitung

HUANUO

HUANUO HNLL11 Bedienungsanleitung

HUANUO

HUANUO HNMS03 Bedienungsanleitung

HUANUO

HUANUO HNWDS1 Bedienungsanleitung

Beliebte Rack & Stand Handbücher anderer Marken

Salamander

Salamander Acadia AC/W/L400/WH Bedienungsanleitung

Fohhn

Fohhn VAT-09 Benutzerhandbuch

ricoo

ricoo FS0522 Bedienungsanleitung

AMSOIL

AMSOIL BMK-22 Kurzanleitung

Kargo Master

Kargo Master 48220 Bedienungsanleitung

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Bedienungsanleitung

ricoo

ricoo S1222 Bedienungsanleitung

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Bedienungsanleitung

VidaBox

VidaBox VB MNT FFS2 Bedienungsanleitung

Welch Allyn

Welch Allyn 48960 Bedienungsanleitung

Arkon

Arkon CM035-ST-2 Bedienungsanleitung

PROEL

PROEL PLWIN60C Bedienungsanleitung

Agilent Technologies

Agilent Technologies E2609B Bedienungsanleitung

Mustang

Mustang MV-ARM4 Bedienungsanleitung

Mounting Solutions

Mounting Solutions WRM-320 Bedienungsanleitung

Pyle

Pyle PMKSPAD1 Bedienungsanleitung

ShelterIt

ShelterIt 21208 Bedienungsanleitung

SPL

SPL RackPack?4 1040 Bedienungsanleitung