Huawei OptiX OSN 8800 T64 Bedienungsanleitung

HUAWEI TECHNOLOGIES CO., LTD.

OptiX OSN 8800 Intelligent Optical Transport

Platform

Quick Installation Guide

Issue: 15

Date: 2017-09-30

Huawei Technologies Co., Ltd.

Address: Huawei Industrial Base

Bantian, Longgang

Shenzhen 518129

People's Republic of China

Website: http://www.huawei.com

Email: [email protected]

No part of this document may be reproduced or transmitted in any form or by any means without prior

written consent of Huawei Technologies Co., Ltd.

Trademarks and Permissions

and other Huawei trademarks are trademarks of Huawei Technologies Co., Ltd.

All other trademarks and trade names mentioned in this document are the property of their respective

holders.

Notice

The purchased products, services and features are stipulated by the contract made between Huawei and

the customer. All or part of the products, services and features described in this document may not be

within the purchase scope or the usage scope. Unless otherwise specified in the contract, all statements,

information, and recommendations in this document are provided "AS IS" without warranties, guarantees

or representations of any kind, either express or implied.

The information in this document is subject to change without notice. Every effort has been made in the

preparation of this document to ensure accuracy of the contents, but all statements, information, and

recommendations in this document do not constitute a warranty of any kind, express or implied.

End

Engineering Labels

Page 135

to 136

Installing and

Routing Fibers (in a

Fiber Management

Frame)

Page 128

to 131

Installing and

Routing Fibers

Page 122

to 127

Installing and

Routing Alarm

Cables to Cabinet

Indicators

Page 107

to 109

Installing/Routing

Power Cables

Page 45 to

Installation Flow

Before

You

Start Installation

Precautions

Page 1

to 2

Start

Introduction to

Installation

Features of the

8800 T64

Page 3

Required Tools

and Equipment

Page 5

Page 22 to

Checking SCC/XCH

Board Battery

Jumper Settings

Installing Subracks

Page 20 to

Page 19 Installing Subrack

Handles

Installation Holes for

the Subrack

Page 10 to

PDF Circuit Breaker

Page 46 to

Selecting Power CablesPage 48

Installing Power Cables

Between the DPD63-8-8

PDU and PDF

Page 50 to

Installing Power Cables

Between the TN16PDU

and PDF

Page 55 to

Subrack Power Cable

Connections

Page 59 to

Routing Ground and

Power Cables

Page 57 to

Installing Boards

Page 25 to

Appearance of the

Subrack

Page 6 to

Installing and

Routing NM

Cables

Page 94 to

100

Installing and

Routing Cables to

the CRPC/ROP

Page 118

to 121

Installing and Routing

External Alarm

Cables

Page 101

to 106

Installing Ground

Cables

Page 40 to

Installing and

Routing Clock

Cables

Page 110

to 117

Installing

Components

Page 10 to

Cable Holes on

Cabinets

Page 49

Reference information

Operation

Requirements and

Precautions for

Operating Boards

Page 4

Page 29 Setting Board

Jumpers

Page 30 Installing

CRPC/ROP Frames

Page 30 to

31 Installing DCM

Frames

Page 34 Installing Optical

Attenuators

Configuring

Master/Slave

Subracks

Page 35 to

Power Redundancy

Page 75 to

Installing and Routing

Subrack Power Cables

Page 79 to

Checking the

Installation

Page 132

to 133

Setting Up Optical

Paths

Page 134

Page 122 Precautions

Open Corrugated

Pipe

Page 122

Page 123 Installing and

Routing External

Fibers

Page 124 Installing and

Routing Fibers to a

DCM Frame

Page 125

to 126 Installing and

Routing Fibers

Between Subracks

Page 126 Installing and

Routing Fibers to a

CRPC Frame

Installing and

Routing Fibers

Between Cabinets

Page 127

Page 32 to

33 Installing the Y-

cable

Page 124 Installing and

Routing Fibers of

the Y-Cable

Installing/Routing

Power Cables-AC

Page 45

CAUTION

ESD Protection

Always wear ESD gloves or an ESD wrist strap prior to contact with the equipment or before handling devices, boards, or IC chips

to prevent damage to sensitive components due to electrostatic discharge from the human body. Ensure that the ESD wrist strap is

properly grounded.

Safety Information

Always wear protective gloves when lifting or transporting a cabinet to prevent hand injuries or damage to the cabinet surface.

The equipment is heavy. To prevent human injuries or equipment damage, always use a lifting device to transport or position the

equipment. Use a pallet truck or heavy-duty bogie wagon to transport the equipment on even ground, and use a cargo lift to transport

the equipment between different floors. If the equipment room does not have a cargo lift, a stair-climbing truck is recommended to

transport the equipment between different floors.

CAUTION

This document provides guidelines for quick hardware installation. It describes procedures for onsite installation, but does

not describe pre-delivery assembly.

NOTE

Installation Precautions

ESD jacks on the T32 subrack

ESD jacks on the T64 subrack

CAUTION

In different subracks, the minimum distance (L) between the board ejector lever and the cabinet door must meet

the following requirements:

•8800 T64/T32/T16 subracks, 8800 Universal platform subrack (DC power supply): L ≥ 50mm.

•8800 Universal platform subrack (AC power supply): L ≥ 75 mm.

CAUTION

Pre-Installation Check

Ensure that the equipment room, cabinets, power supplies, ground cables, optical cables, and associated devices are ready for

installation. Start the installation according to the engineering design documents after confirming that all conditions are met.

Bundling Cables

Binding intervals between cable ties or optical fiber binding straps inside the cabinet cannot exceed 250 mm. (Binding intervals

cannot exceed 200 mm for user cables.)

Binding intervals between cable ties for all cables and corrugated pipes outside the cabinet are determined based on the distance

between the two horizontal beams. If the cable trough does not contain any beams, the binding intervals between cable ties cannot

exceed 250 mm.

CAUTION

Installation Precautions

ESD jacks on the universal platform subrack

ESD jacks on the T16 subrack

Precautions for Installing the OptiX OSN 8800 T64:

1. Transportation

Move an N66B cabinet with a tool but not hands to avoid bodily injuries or damages to equipment. To move an

N66 cabinet on a flat ground, use a fork truck or heavy-duty flat car; to move the cabinet from one floor to

another, use a goods elevator. In a telecommunications room without a goods elevator, use auxiliary devices

such as a transportation vehicle applicable to transportation along stairs to move the cabinet.

2. Cabinet installation

There is no space for you to use a tool to install screws on the feet of a cabinet because the

equipment is highly integrated. Therefore you need to remove the DCM frame before installing the

cabinet.

3. Installation of cables and fibers

If there are subracks delivered separately on site, after you install them in a cabinet, connect power cables to

PIU boards, and ground cables, cascading network cables, and cascading fibers to the subracks.

4. Installation of clock cables

Clock cables must be installed on site according to configuration requirements.

5. Installation of fibers

If there are subracks delivered separately on site, after you install them in a cabinet, connect internal cascading

fibers between subracks and external fibers. When connecting fibers between the front side and rear side of the

OptiX OSN 8800 T64 subrack, route fibers through the bottom of the subrack. In this case, the fibers must be

protected in winding pipes at throughholes.

6. Power supply

The maximum power consumption of a fully-configured N66B cabinet is 9600 W and the cabinet requires 16

power supplies.

For more details, see the following parts of this document.

Introduction to Installation Features of the OptiX OSN 8800 T64

Requirements and Precautions for Operating Boards

Always wear ESD gloves or an ESD wrist strap prior to operating a board to prevent damage to sensitive

components.

Any vacant slot must be covered by a filler panel to prevent foreign objects from entering the subrack or system

ventilation ducts. Foreign objects may cause an NE failure.

Boards are fragile and vulnerable. When transporting or placing a board, exercise caution and ensure that the

board is packed in a dedicated box to protect the board against damage.

Boards must be packed with original packaging materials during transportation. If the original packaging

materials are lost, contact Huawei.

Operating a board without ESD

protection

Wearing ESD gloves Wearing an ESD wrist strap

Hold the front panel of a board with both hands.

CAUTION

Measuring tape

Phillips screwdriver

Flat-head screwdriver

Adjustable wrench Heat gun Segmented blade utility knife

COAX crimping tool

Cable cutter Wire stripper

Power cable crimping tool Network cable

tester

COAX stripper

RJ45 crimping tool Diagonal pliers

Multimeter

Claw hammer Hammer drill

Socket wrench

Marker

Required Tools and Equipment

Board

area

Fiber

cabling

area

Air filter

Fiber

spool

Fan tray

assembly

Mounting

ear

Fan tray

assembly

Appearance of the Subrack

2 OptiX OSN 8800 T64 Subrack

OSN8800T64

A subrack identified by "Enhanced" is an enhanced OptiX OSN 8800 T64 subrack. If the subrack is not identified by

"Enhanced", it is a general OptiX OSN 8800 T64.

NOTE

1 Product Access

Product Initial Supportive Product Version

OptiX OSN 8800 T64 subrack V100R002C00

OptiX OSN 8800 T32 subrack V100R002C00

OptiX OSN 8800 T16 subrack V100R006C00

OptiX OSN 8800 Universal Platform Subrack V100R008C00

Item Specification

Dimensions 498 mm (W) x 580 mm (D) x 900 mm (H) (19.6 in. (W)x 22.8 in. (D) x 35.4 in. (H))

Weight (empty subracka) 65 kg (143 lb.)

a: An empty subrack means no boards are installed in the board area, and no fan tray assembly or air filter is installed.

This end is secured to

the subrack.

Mounting ear

for the left side

of the subrack

Mounting ear for

the right side of

the subrack

3 OptiX OSN 8800 T32 Subrack

OSN8800T32

A subrack identified by "Enhanced" is an enhanced OptiX OSN 8800 T32 subrack. If the subrack is not

identified by "Enhanced", it is a general OptiX OSN 8800 T32.

NOTE

Board area

Fiber cabling area

Air filter

Fiber spool

Fan tray assembly

Mounting ear

Fan tray assembly

Item Specification

Dimensions 498 mm (W) x 295 mm (D) x 900 mm (H) (19.6 in. (W)x 11.6 in. (D) x 35.4 in. (H))

Weight (empty subracka) 35 kg (77.1 lb.)

a: An empty subrack means no boards are installed in the board area, and no fan tray assembly or air filter is installed.

This end is secured to the subrack.

Mounting ear

for the left side

of the subrack

Mounting ear for

the right side of

the subrack

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Huawei Netzwerk-Hardware Handbücher

Huawei

Huawei TP48200A-HT19C4-1 Bedienungsanleitung

Huawei

Huawei CR52-10GE Bedienungsanleitung

Huawei

Huawei EchoLife HS8245W Bedienungsanleitung

Huawei

Huawei OptiX OSN 3500 Gebrauchsanweisung

Huawei

Huawei PDU8000 Series Bedienungsanleitung

Huawei

Huawei CR-P4CF Bedienungsanleitung

Huawei

Huawei VP9650 Technische Daten

Huawei

Huawei CR52-MPUA Bedienungsanleitung

Huawei

Huawei SSC2132T Technische Daten

Huawei

Huawei IdeaShare Key Bedienungsanleitung

Huawei

Huawei HG8145V5 Bedienungsanleitung

Huawei

Huawei OptiX RTN 950A Bedienungsanleitung

Huawei

Huawei OptiXstar S890H Bedienungsanleitung

Huawei

Huawei iSitePower-M Bedienungsanleitung

Huawei

Huawei MTS9300A Bedienungsanleitung

Huawei

Huawei RTN XMC ODU V200 Bedienungsanleitung

Huawei

Huawei Telecom Power TP48120A-HD15A1 Bedienungsanleitung

Huawei

Huawei LSBM1FP20B0 Bedienungsanleitung

Huawei

Huawei XMC-1 ODU Bedienungsanleitung

Huawei

Huawei EN83CTLC Bedienungsanleitung

Huawei

Huawei 21501043-003 Bedienungsanleitung

Huawei

Huawei PDU8000 Series Bedienungsanleitung

Huawei

Huawei CR52-4xPOS/STM4-SFP Bedienungsanleitung

Huawei

Huawei PDU8000 Series Bedienungsanleitung

Beliebte Netzwerk-Hardware Handbücher anderer Marken

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Bedienungsanleitung

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Bedienungsanleitung

Yudor

Yudor YDS-16 Bedienungsanleitung

D-Link

D-Link ShareCenter DNS-320L Bedienungsanleitung

Samsung

Samsung ES1642dc Gebrauchsanweisung

Honeywell Home

Honeywell Home LTEM-PV Montageanleitung

evertz

evertz 7700 Series Bedienungsanleitung

D-Link

D-Link ShareCenter DNS-343 Bedienungsanleitung

Asante

Asante AsanteBridge 1012 Bedienungsanleitung

FireBrick

FireBrick FB2700 Bedienungsanleitung

Audiovox Electronics

Audiovox Electronics ARWH2T Bedienungsanleitung

ADC

ADC DSX-1 Handbuch

NetComm

NetComm NF2 Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 5620 Bedienungsanleitung

Dell EMC

Dell EMC XC6420 Series Bedienungsanleitung

Lanner

Lanner NCA-1020A Bedienungsanleitung

Allied Telesis

Allied Telesis AT-TN121-A Bedienungsanleitung

Arista

Arista CCA-ETM-Q12 Bedienungsanleitung