Huawei HG531s V1 Bedienungsanleitung

HG531s V1 300Mbps Wireless ADSL2+ Router

Quick Start

1 Connecting Cables

If you have subscribed to digital subscriber line (DSL) broadband, you can connect

the HG531s V1 to a telephone port for Internet access.

Follow the steps in the following figure to connect devices properly.

When configuring the HG531s V1 for the first time, use an Ethernet cable to

connect the HG531s V1 to a computer.

1 Telephone wall jack 2 Splitter 3 Telephone

4 Power adapter 5 Desktop computer 6 Set-top Box

7 Laptop computer 8 Smart Phone 9 Pad

a LINE port b MODEM port c PHONE port

MODEM

PHONE

LINE

2 Powering On

To power on the HG531s V1, press its power button.

After the HG531s V1 is powered on, the HG531s V1 indicator turns on. The following

table lists how the indicators behave when the HG531s V1 is operating correctly. If

the indicators do not behave as expected, ensure that everything is plugged in

correctly.

Indicator Expected State Description

Power Steady green The HG531s V1 is powered on.

ADSL

Blinking green A DSL connection is being activated.

Steady green A digital subscriber line (DSL) connection has been

set up and activated.

Internet

Blinking green The HG531s V1 is connected to the Internet in

router mode, and data is being transmitted.

Steady green The HG531s V1 is connected to the Internet in

router mode, but no data is being transmitted.

Off

The HG531s V1 is in router mode, but not

connected to the Internet.

The HG531s V1 is in bridge mode.

WLAN

Blinking green The HG531s V1 has WLAN enabled, and data is

being transmitted.

Steady green The HG531s V1 has WLAN enabled, but is not

transmitting data.

WPS

Blinking green

The HG531s V1 is attempting to connect to a

wireless client over the WLAN using the WPS

function.

The WPS indicator blinks for 120 seconds or less.

Steady green

The HG531s V1 is connected to a wireless client,

such as a computer with a wireless network

adapter, over the WLAN using the Wi-Fi Protected

Setup (WPS) function.

The WPS indicator is steady on for 300 seconds.

3 Setting Dial-Up Connection Parameters

Configuring a Dial-Up Connection to Access the Internet

The HG531s V1 works in bridge mode by default. You need to install and configure a

dial-up connection on your computer, and perform it each startup.

Before setting dial-up connection parameters, verify that the HG531s V1 is correctly

connected to your computer and you have the dial-up connection account name and

password provided by your Internet service provider (ISP). This section

demonstrates how to set up a Point-to-Point Protocol over Ethernet (PPPoE)

connection on Windows.

On Windows 7

1. Choose Start > Control Panel > Network and Internet > Network and

Sharing Center.

2. Under Change your networking settings, click Set up a new connection or

network.

3. In the Set Up a Connection or Network window, select Connect to the

Internet and click Next.

4. Click Broadband (PPPoE).

5. In User name and Password, enter the dial-up connection account name and

password provided by your ISP. In Connection name, name the dial-up

connection. Select or deselect Allow other people to use this connection.

Then click Connect.

LAN1 ～

LAN4

Blinking green The LAN port is connected to an Ethernet device

with a network cable, and data is being transmitted.

Steady green

The LAN port is connected to an Ethernet device

(such as a computer) with a network cable, but no

data is being transmitted.

USB

Blinking green The HG531s V1 is connected to a USB device, and

data is being transmitted.

Steady green The HG531s V1 is connected to a USB device, but

no data is being transmitted.

Indicator Expected State Description

6. Return to the Network and Sharing Center page. Click Change adapter

settings. Right-click the icon for the dial-up connection you just set up and

choose Create Shortcut from the shortcut menu. In the displayed dialog box,

click Yes.

On Windows XP

1. Choose Start > Control Panel > Network and Internet Connections >

Network Connections.

2. Under Network Tasks, click Create a New Connection.

3. In the Network Connection Wizard dialog box, click Next.

4. Select Connect to the Internet and click Next.

5. Select Set up my connection manually and click Next.

6. Select Connect using a broadband connection that requires a user name

and password and click Next.

7. In ISP Name, name the dial-up connection. Click Next.

8. Select Anyone's use or My use only and click Next.

9. Enter the dial-up connection account name and password provided by your

ISP and click Next.

10. Select Add a shortcut to this connection to my desktop and click Finish.

After you successfully set up a PPPoE connection, a dial-up connection icon is

displayed on your computer desktop.

To connect to the Internet, double-click the dial-up connection icon. In the displayed

dialog box, click Connect.

Configuring a Wireless Account

Before you log in to the HG531s V1 web management page, ensure that the

computer used for the login is connected to the HG531s V1 and has been configured

to automatically obtain an IP address or assigned with a static IP address.

The HG531s V1 provides an intuitive web management page where you can view or

set the HG531s V1 parameters. After you log in to the web management page, you

will see a configuration wizard page used to configure the wireless account.

The default SSID and WLAN Key printed on the HG531s V1's rear panel

are unique and secure. If you do not want to change them, click Next.

For security reasons or to make the password easy to remember, you can change

the wireless network name and password as follows:

1. Open a browser. In the address box, enter 192.168.1.1. Press Enter.

2. Enter the login user name (user by default) and password (@User1234 by

default). Click Login.

3. On the Quick Configure Router: Wireless Network page, enter your desired

WLAN name and password in WLAN SSID and Key, and click Next.

4 Wireless Connection Setup

The wireless configuration software provided by Windows is used as an example to

describe how to set up a wireless connection.

Before setting wireless connection, find the SSID and WLAN Key printed on the label

on the HG531s V1's rear panel.

On Windows 7

1. Click in the lower right corner of your desktop.

2. From the wireless network list, select the WLAN provided by the HG531s V1.

Click Connect.

3. In the displayed dialog box, enter the WLAN password and click OK.

4. In the wireless network list, check the WLAN connection status. If the status is

Connected, the computer is wirelessly connected to the HG531s V1.

On Windows XP

1. Click in the lower right corner of your desktop.

2. From the wireless network list, select the WLAN provided by the HG531s V1.

Click Connect.

3. In the displayed dialog box, enter the WLAN password and click Connect.

4. In the wireless network list, check the WLAN connection status. If the status is

Connected, the computer is wirelessly connected to the HG531s V1.

5 Security Maintenance Guide

Changing the Web Management Page User Name and

Password

The correct user name and password are required to log in to the web management

page. Regular changes to the web management page user name and password can

effectively prevent unauthorized users from logging in and modifying important

parameters.

1. Log in to the web management page.

2. In the navigation tree, choose Maintenance > Account.

3. In New user name, enter your desired user name.

4. In Current password, enter the currently used password.

5. In New password, enter the new password you specified. In Confirm

password enter the new password again.

6. Click Submit.

When modify password successfully, this page will jump to the login

page, enter the new user name and password to log in.

If you forget the password , you can press and hold the Reset button for 6

seconds or more, then the user name and password of the Web

management page will back to factory value. This operation will make your

own configuration data lost, please perform this operation with caution.

Changing Your WLAN Name and Password

WLAN access requires the WLAN name and password. To improve your WLAN

security, regularly change your WLAN name and password.

1. Log in to the web management page.

2. In the navigation tree, choose Basic > WLAN.

3. On the displayed page, enable your WLAN.

4. On the Wireless Settings area, enter your desired WLAN name and

password in SSID and WPA pre-shared key, and click Submit.

96722586_01

6 Safety information

This section contains important information about the operation of your device. It also contains

information about how to use the device safely. Read this information carefully before using your

device.

Electronic device

Do not use your device if using the device is prohibited. Do not use the device if doing so causes

danger or interference with other electronic devices.

Interference with medical equipment

> Follow rules and regulations set forth by hospitals and health care facilities. Do not use your

device where prohibited.

> Some wireless devices may affect the performance of hearing aids or pacemakers. Consult

your service provider for more information.

> Pacemaker manufacturers recommend that a minimum distance of 15 cm be maintained

between a device and a pacemaker to prevent potential interference with the pacemaker. If

using a pacemaker, hold the device on the side opposite the pacemaker and do not carry the

device in your front pocket.

Areas with flammables and explosives

> Do not use the device where flammables or explosives are stored (in a gas station, oil depot,

or chemical plant, for example). Using your device in these environments increases the risk of

explosion or fire. In addition, follow the instructions indicated in text or symbols.

> Do not store or transport the device in containers with flammable liquids, gases, or explosives.

Operating environment

> Avoid dusty, damp, or dirty environments. Avoid magnetic fields. Using the device in these

environments may result in circuit malfunctions.

> Before connecting and disconnecting cables, stop using the device and disconnect it from the

power supply. Ensure that your hands are dry during operation.

> Place the device on a stable surface.

> Keep the device away from electronic appliances that generate strong magnetic or electric

fields, such as a microwave oven or refrigerator.

> During thunderstorms, power off your device and remove all cables connected to it to protect

against lightning strikes.

> Do not use your device during thunderstorms to protect your device against any danger

caused by lightning.

> Ideal operating temperatures are 0 °C to 40 °C. Extreme heat or cold may damage your

device or accessories.

> Keep the device and accessories in a well-ventilated and cool area away from direct sunlight.

Do not enclose or cover your device with towels or other objects. Do not place the device in a

container with poor heat dissipation, such as a box or bag.

> To protect your device or accessories from fire or electrical shock hazards, avoid rain and

moisture.

> Keep the device away from sources of heat and fire, such as a heater, microwave oven,

stove, water heater, radiator, or candle.

> Do not place any object, such as a candle or a water container, on the device. If any foreign

object or liquid enters the device, immediately stop using it, power it off, and remove all cables

connected to it. Then, contact an authorized service center.

> Observe local laws and regulations, and respect the privacy and legal rights of others.

> Do not block device openings. Reserve a minimum of 10 cm around the device to dissipate

heat.

> Stop using your device or applications for a while if the device is overheated. If skin is

exposed to an overheated device for an extended period, low temperature burn symptoms,

such as red spots and darker pigmentation, may occur.

> Do not touch the device's antenna. Otherwise, communication quality may be reduced.

> Do not allow children or pets to bite or suck the device or accessories. Doing so may result in

damage or explosion.

> The device should be installed and operated with a minimum distance of 20 cm between the

radiator and your body.

> Keep the device in a place with good reception. The distance between the device and other

metal materials (such as metal brackets or metal doors and windows) should be greater than

25 cm and the distance between the device should be greater than 30 cm.

> If you connect a USB device to the HG531s V1, verify that the input voltage and current of the

USB device does not exceed 5V/0.65A. Otherwise, the HG531s V1 may malfunction.

Child's safety

> Comply with all precautions with regard to child's safety. Letting children play with the device

or its accessories may be dangerous. The device includes detachable parts that may present

a choking hazard. Keep away from children.

Accessories

> Using an unapproved or incompatible power adapter, charger or battery may cause fire,

explosion or other hazards.

> Choose only accessories approved for use with this model by the device manufacturer. The

use of any other types of accessories may void the warranty, may violate local regulations

and laws, and may be dangerous. Please contact your retailer for information about the

availability of approved accessories in your area.

Power adapter safety

> The power plug is intended to serve as a disconnect device.

> For pluggable devices, the socket-outlet shall be installed near the devices and shall be easily

accessible.

> Unplug the power adapter from electrical outlets and the device when not in use.

> Do not drop or cause an impact to the power adapter. If it is damaged, take it to an authorized

service center for inspection.

> If the power cable is damaged (for example, the cord is exposed or broken), or the plug

loosens, stop using it at once. Continued use may lead to electric shocks, short circuits, or

fire.

> Do not touch the power cord with wet hands or pull the power cord to disconnect the power

adapter.

> Do not touch the device or the power adapter with wet hands. Doing so may lead to short

circuits, malfunctions, or electric shocks.

> If your power adapter has been exposed to water, other liquids, or excessive moisture, take it

to an authorized service center for inspection.

> Ensure that the power adapter meets the requirements of Clause 2.5 in IEC60950-1/

EN60950-1 and has been tested and approved according to national or local standards.

Cleaning and maintenance

> During storage, transportation, and operation of the device, keep it dry and protect it from

collision.

> Keep the device and accessories dry. Do not attempt to dry it with an external heat source,

such as a microwave oven or hair dryer.

> Do not expose your device or accessories to extreme heat or cold. These environments may

interfere with proper function and may lead to fire or explosion.

> Avoid collision, which may lead to device malfunctions, overheating, fire, or explosion.

> If the device is not going to be used for an extended period of time, power it off, and remove all

cables connected to it.

> If anything unusual occurs (for example, if the device emits smoke or any unusual sound or

smell), immediately stop using it, power it off, remove all cables connected to it, and contact

an authorized service center.

> Do not trample, pull, or excessively bend any cable. Doing so may damage the cable, causing

the device to malfunction.

> Before you clean or maintain the device, stop using it, stop all applications, and disconnect all

cables connected to it.

> Do not use any chemical detergent, powder, or other chemical agents (such as alcohol and

benzene) to clean the device or accessories. These substances may cause damage to parts

or present a fire hazard. Use a clean, soft, and dry cloth to clean the device and accessories.

> Do not place magnetic stripe cards, such as credit cards and phone cards, near the device for

extended periods of time. Otherwise the magnetic stripe cards may be damaged.

> Do not dismantle or remanufacture the device and its accessories. This voids the warranty

and releases the manufacturer from liability for damage. In case of damage, contact an

authorized service center for assistance or repair.

Disposal and recycling information

This symbol (with or without a solid bar) on the device, batteries (if included), and/or

the packaging, indicates that the device and its electrical accessories (for example, a headset,

adapter, or cable) and batteries should not be disposed of as household garbage. These items

should not be disposed of as unsorted municipal waste and should be taken to a certified collection

point for recycling or proper disposal.

For more detailed information about device or battery recycling, contact your local city office,

household waste disposal service, or retail store.

Disposal of the device and batteries (if included) is subject to WEEE Directive Recast (Directive

2012/19/EU) and Battery Directive (Directive 2006/66/EC). The purpose of separating WEEE and

batteries from other waste is to minimize the potential environmental impacts and human health

risk of any hazardous substances that may be present.

Reduction of hazardous substances

This device is compliant with the REACH Regulation [Regulation (EC) No 1907/2006] and RoHS

Directive Recast (Directive 2011/65/EU). Batteries (if included) are compliant with the Battery

Directive (Directive 2006/66/EC). For up-to-date information about REACH and RoHS compliance,

please visit the web site www.huaweidevice.com/certification.

EU regulatory conformance

Statement

Hereby, Huawei Technologies Co., Ltd. declares that this device is in compliance with the essential

requirements and other relevant provisions of Directive 1999/5/EC.

For the declaration of conformity, visit the web site www.huaweidevice.com/certification.

The following marking is included in the product:

This device may be operated in all member states of the EU.

Observe national and local regulations where the device is used.

This device may be restricted for use, depending on the local network.

Restrictions in the 2.4 GHz band:

Norway: This subsection does not apply for the geographical area within a radius of 20 km from the

centre of Ny-Ålesund.

FCC Regulatory Compliance

FCC statement

This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equipment generates, uses and can

radiate radio frequency energy and, if not installed and used in accordance with the instructions,

may cause harmful interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the interference by one or more of the following

measures:

--Reorient or relocate the receiving antenna.

--Increase the separation between the equipment and receiver.

0979

Inhaltsverzeichnis

Andere Huawei Netzwerk-Router Handbücher

Huawei

Huawei AR150 series Bedienungsanleitung

Huawei

Huawei V100R006C00 Bedienungsanleitung

Huawei

Huawei H112 Bedienungsanleitung

Huawei

Huawei Quidway S3526 Bedienungsanleitung

Huawei

Huawei EchoLife EG8041V5 Bedienungsanleitung

Huawei

Huawei EchoLife HG8245 Bedienungsanleitung

Huawei

Huawei Quidway AR 46 Series Bedienungsanleitung

Huawei

Huawei Quidway S1700-24-AC Bedienungsanleitung

Huawei

Huawei NE20E-S Series Leitfaden

Huawei

Huawei Quidway NetEngine80E Bedienungsanleitung

Huawei

Huawei B311s-220 Bedienungsanleitung

Huawei

Huawei EchoLife BM625 WiMAX CPE Bedienungsanleitung

Huawei

Huawei Aolynk VDR824 Bedienungsanleitung

Huawei

Huawei WS880 Bedienungsanleitung

Huawei

Huawei AR530 Series Bedienungsanleitung

Huawei

Huawei E5180 Bedienungsanleitung

Huawei

Huawei AR1200 Series Bedienungsanleitung

Huawei

Huawei EchoLife HG8245A Technische Daten

Huawei

Huawei B315S-607 Bedienungsanleitung

Huawei

Huawei WiFi Mesh 3 Bedienungsanleitung

Huawei

Huawei NT3BB-4PVWN-147 Bedienungsanleitung

Huawei

Huawei E5180s-22 Technische Daten

Huawei

Huawei WA8021V5 Bedienungsanleitung

Huawei

Huawei Quidway S9300 Bedienungsanleitung

Beliebte Netzwerk-Router Handbücher anderer Marken

Allnet

Allnet ALL0333AU Bedienungsanleitung

HomeSeer

HomeSeer HT-SEL Bedienungsanleitung

Sercomm

Sercomm Genesis OC3505D Bedienungsanleitung

Billion

Billion BIPAC 5102 Series Bedienungsanleitung

TP-Link

TP-Link TD-8817 Bedienungsanleitung

Motorola

Motorola MR1900 Bedienungsanleitung

Digi

Digi IX14 Bedienungsanleitung

Cisco

Cisco NCS 540 Handbuch

XAVi

XAVi X8821e Bedienungsanleitung

BEC

BEC 6200WZL Bedienungsanleitung

MikroTik

MikroTik hAP ac3 Series Bedienungsanleitung

Korenix

Korenix JetNet 5428G Series Bedienungsanleitung

NETGEAR

NETGEAR FS526T - Switch Bedienungsanleitung

Korenix

Korenix JetNet 5710G Series Bedienungsanleitung

Automated Logic

Automated Logic ZN551 Betriebsanleitung

Cisco

Cisco ASR 1000 Series Bedienerhandbuch

EnGenius

EnGenius ESR-9710 Bedienungsanleitung

Cisco

Cisco 805 Series Bedienungs- und Sicherheitshinweise